iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1452-4:1999

(Main)

Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves and ancillary equipment

Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves and ancillary equipment

This Part of prEn 1452 specifies the characteristics of valves and ancillary equipment made from unplasticized poly(vinyl chloride) (PVC-U) for piping systems in the field of water supply. It also specifies the test parameters for the test methods referred to in this standard.

Kunststoff-Rohrleitungssysteme für die Wasserversorgung - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 4: Armaturen und Zubehör

Dieser Teil der prEN 1452 legt Anforderungen an Armaturen und Zubehörteile aus weichmacherfreiem Polyvinylchlorid (PVC-U) fest, die in Rohrleitungssystemen für die Wasserversorgung eingesetzt werden. In diesem Teil sind auch die Prüfparameter für die Prüfverfahren festgelegt, auf die in dieser Norm verwiesen wird.

Systèmes de canalisations en plastique pour alimentation en eau - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 4: Robinets et équipements auxiliaires

La présente partie du prEN 1452 spécifie les caractéristiques des robinets et des équipements auxiliaires fabriqués à partir de poly(chlorure de vinyle) non plastifié (PVC-U) pour les sytèmes de canalisations dans le domaine de l'alimentation en eau. Elle spécifie aussi les paramètres d'essai pour les méthodes d'essai auxquelles il est fait référence dans la présente norme.

Cevni sistemi iz polimernih materialov za oskrbo z vodo - Nemehčan polivinilklorid (PVC-U) - 4. del: Ventili in pomožna oprema

General Information

Status
Withdrawn
Publication Date
22-Jun-1999
Withdrawal Date
30-Nov-2009
ICS
23.060.01 - Valves in general
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 8 - Systems for water supply and pressure drainage and sewerage - PVC-U (solid wall)
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Dec-2009
Completion Date
01-Dec-2009
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
Mandate
M/BC/CEN/88/15 - Standardization request to CEN/CENELEC in the field of Water supply, drainage and sewerage
Ref Project
SIST EN 1452-4:2000 - Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves and ancillary equipment

Relations

Replaced By
EN ISO 1452-4:2009 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves (ISO 1452-4:2009)
Effective Date
08-Jun-2022

Buy Standard

EN 1452-4:2000EN 1452-4:2000
PreviousNext
Standard
EN 1452-4:2000
English language
30 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoff-Rohrleitungssysteme für die Wasserversorgung - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 4: Armaturen und ZubehörSystemes de canalisations en plastique pour alimentation en eau - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 4: Robinets et équipements auxiliairesPlastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves and ancillary equipment91.140.60Sistemi za oskrbo z vodoWater supply systems23.060.01Ventili na splošnoValves in generalICS:Ta slovenski standard je istoveten z:EN 1452-4:1999SIST EN 1452-4:2000en01-junij-2000SIST EN 1452-4:2000SLOVENSKI
STANDARD



S
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 17778:2015(Main)
Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships (ISO 17778:2015)
SIST EN ISO 17778:2015

ISO 17778:2015 specifies a method for determining the flow rate/pressure drop relationship of components for plastics piping systems when tested using air at 25 mbar.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12201-4:2012(Main)
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves
SIST EN 12201-4:2012

This Part of EN 12201 specifies the characteristics of valves or valve bodies made from polyethylene (PE 100 and PE 80) for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes.
NOTE 1   For valves or valve bodies intended for drainage and sewerage under pressure, additional specifications/tests may be necessary according to the requirements of the purchaser, especially for the chemical resistance of the components in contact with the fluids and functioning characteristics.
NOTE 2   For PE components intended for the conveyance of water for human consumption and raw water prior to treatment attention is drawn to 5.4. Components manufactured for water for other purposes may not be suitable for water supply for human consumption.
It also specifies the test parameters for the test methods referred to in this European Standard.
NOTE 3   Valves made from material other than polyethylene (PE) designed for the supply of water intended for human consumption to a relevant standard(s) can be used in PE piping systems conforming to EN 12201 when they have relevant PE connection for butt fusion or electrofusion ends (see EN 12201-3:2011).
In conjunction with Parts 1, 2, 3 and 5 of EN 12201 it is applicable to PE valves, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar  )
b)   an operating temperature of 20 °C as a reference temperature;
c)   buried in the ground;
d)   sea outfalls;
e)   laid in water;
f)   above ground, including pipes suspended below bridges.
NOTE 4   For applications operating at constant temperature greater than 20 °C and up to 40 °C, see EN 12201 1:2011, Annex A.
EN 12201 covers a range of allowable operating pressures and gives requirements concerning colours and additives.
NOTE 5   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
This Part of EN 12201 covers valves for pipes with a nominal outside diameter dn ≤ 315 mm.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1452-4:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves (ISO 1452-4:2009)
SIST EN ISO 1452-4:2010

ISO 1452-4:2009 specifies the characteristics of valves made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1, ISO 1452-2, ISO 1452-3 and ISO 1452-5 it is applicable to PVC‑U valves with components of PVC-U, other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above-ground drainage and sewerage under pressure.
It is applicable to valves in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to valves for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12119:1997(Main)
Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to thermal cycling
SIST EN 12119:1999

This standard specifies a test method for the resistance of valves to thermal cycling. This standard is applicable to polyethylen (PE) valves and valves with PE spigot-ends having a nominal outside diameter greater than 63 mm and intended for the transport of fluids.

  • Standard
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1680:1997(Main)
Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms
SIST EN 1680:1999

This draft standard specifies a method for testing the ability of a valve, intended for use in PE piping systems for gas supply, to maintain its pressure retaining capabilities under and after being subject to a bending moment appliedto the operating mechanism (cap).

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1705:1996(Main)
Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow
SIST EN 1705:1997

This standard specifies a method for determining the leaktightness and the ease of operation of a valve following an impact applied to the operating mechanism (cap) or other exposed mechanism.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
FprEN 12201-4(Main)
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 4: Valves for water supply systems
oSIST prEN 12201-4:2021

This document specifies the characteristics of valves or valve bodies made from polyethylene (PE) for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes.
It is applicable to isolating unidirectional and bi-directional valves with spigot ends or electrofusion sockets intended to be fused with PE pipes or fittings conforming to prEN 12201 2 and prEN 12201 3 respectively.
Valves made from materials other than PE, designed for the supply of water, drainage and sewerage under pressure conforming to the relevant standards can be used in PE piping systems according to EN 12201, provided that they have PE connections for butt fusion or electrofusion ends, including integrated material transition joints, conforming to prEN 12201 3.
NOTE 1   For valves or valve bodies intended for drainage and sewerage under pressure, additional specifications/tests could be necessary according to the requirements of the purchaser, especially for the chemical resistance of the components in contact with the fluids and functioning characteristics.
NOTE 2   For PE components intended for the conveyance of water for human consumption and raw water prior to treatment attention is drawn to 5.4. Components manufactured for water for other purposes are possibly not suitable for water supply for human consumption.
It also specifies the test parameters for the test methods referred to in this document.
NOTE 3   Valves made from material other than polyethylene (PE) designed for the supply of water intended for human consumption to a relevant standard(s) can be used in PE piping systems conforming to EN 12201 when they have relevant PE connection for butt fusion or electrofusion ends (see prEN 12201 3:2021).
In conjunction with Parts 1, 2, 3 and 5 of EN 12201 it is applicable to PE valves, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar );
b)   an operating temperature of 20 °C as a reference temperature;
c)   buried in the ground;
d)   sea outfalls;
e)   laid in water;
f)   above ground, including pipes suspended below bridges.
NOTE 4   For applications operating at constant temperature greater than 20 °C and up to 40 °C, see prEN 12201 1:2021, Annex A.
EN 12201 covers a range of allowable operating pressures and gives requirements concerning colours and additives.
NOTE 5   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
This Part of EN 12201 covers valves for pipes with a nominal outside diameter dn ≤ 400 mm.

  • Draft
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5117:2023(Main)
Automatic steam traps - Production and performance characteristic tests (ISO 5117:2023)
SIST EN ISO 5117:2023

This document specifies the production and performance relevant test requirements for automatic steam traps used for condensate removal/recovery services for optimized utilization of energy, in refinery, power generation or other general applications where steam is used as a medium of heat transfer.
The tests can be classified as production tests and performance characteristic tests and can be conducted to ensure the correct functioning of a steam trap or to evaluate the performance of a particular design. This document specifies the tests performed relative to each one of these two categories and briefly describes the corresponding test methods.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17821:2023(Main)
Building valves - Frost resistant taps for outdoor use (FRT) - General technical specification
SIST EN 17821:2023

This document specifies:
- general construction, performance and material requirements for Frost Resistant Taps for outdoor use (FRT), PN 10.
- the application in the potable water installation with a static pressure of maximum 1,0 MPa (10 bar) and a distribution temperature of maximum 25 °C (PWC).
FRT valves shall consist of the 3 areas shown in Figure 1.
The conditions of use are according to the following Table 1.
The requirements with regard to the potable water quality are specified in national regulations.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10497:2022(Main)
Testing of valves - Fire type-testing requirements (ISO 10497:2022)
SIST EN ISO 10497:2023

This document specifies fire type-testing requirements and a fire type-test method for soft- and metal-seated isolation valves with one or more obturators. It is not applicable to the testing requirements for valve actuators other than manually operated gearboxes or similar mechanisms when these form part of the normal valve assembly. Other types of valve actuators (e.g. electrical, pneumatic or hydraulic) can need special protection to operate in the environment considered in this valve test, and the fire testing of such actuators is outside the scope of this document.
This document specifies the measurement and assessment criteria for:
a) through-seat leakage;
b) external leakage;
c) cavity overpressure relief of double-seated valves;
d) operability.
This document specifies the rules whereby the fire-type testing qualification for a valve can be extended to untested sizes, pressure ratings and materials of construction of the same basic design type.
Fire test reports of valves tested according to previous editions of this document are acceptable when submitted together with the full and compliant fire test report as per 6.7 of the edition under which it was tested. Any data missing as required from 6.7 within the fire test report are accepted or rejected at the purchaser’s discretion.
NOTE       For the purposes of this document, the terms “fire type-test” and “fire test” are synonymous.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day