EN 3386:2012

Aerospace series - Rings retaining, radial mounting, steel, phosphated

This European Standard defines the characteristics of radial mounting retaining rings, in steel, phosphated, for aerospace applications.
These retaining rings are used only when EN 3384 cannot be used for installation problems.
The phosphating restricts the use at temperatures not exceeding 200 °C.

Luft- und Raumfahrt - Sicherungsringe, radial montierbar, aus Stahl, phosphatiert

Diese Norm legt die Merkmale von radial montierbaren Sicherungsringen aus Stahl mit Phosphatbeschichtung
zur Anwendung in der Luft- und Raumfahrt fest.
Diese Sicherungsringe werden nur verwendet, wenn EN 3384 aufgrund von Installationsproblemen nicht
angewandt werden kann.
Die Phosphatbeschichtung beschränkt die Verwendung auf Temperaturen von nicht mehr als 200 °C.

Série aérospatiale - Anneaux d’arrêt, à montage radial, en acier, phosphatés

La présente Norme Européenne définit les caractéristiques des anneaux d’arrêt, à montage radial, en acier, phosphatés pour applications aérospatiales.
Ces anneaux d’arrêt sont seulement utilisés lorsque l'EN 3384 ne peut être employée pour des problèmes de montage.
La phosphatation limite l’utilisation à des températures ne dépassant pas 200 °C.

Aeronavtika - Varnostni obroči za radialno pritrditev, jekleni, fosfatirani

Ta standard določa lastnosti jeklenih fosfatiranih varnostnih obročev za radialno pritrditev za uporabo v aeronavtiki. Ti varnostni obroči se uporabljajo samo, če zaradi težav z inštalacijo ni mogoče uporabiti standarda EN 3384. Fosfatiranje omejuje uporabo na temperature, ki ne presegajo 200 °C.

General Information

• Status: Published
• Publication Date: 06-Mar-2012
• Withdrawal Date: 29-Sep-2012
• ICS: 49.030.50 - Washers and other locking elements
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 3 - Mechanical
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 30-Jun-2017
• Ref Project: SIST EN 3386:2012 - Aerospace series - Rings retaining, radial mounting, steel, phosphated

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.RVIDWLUDQLLuft- und Raumfahrt - Sicherungsringe, radial montierbar, aus Stahl, phosphatiertSérie aérospatiale - Anneaux d’arrêt, à montage radial, en acier, phosphatésAerospace series - Rings retaining, radial mounting, steel, phosphated49.030.50Podložke in drugi blokirni elementiWashers and other locking elementsICS:Ta slovenski standard je istoveten z:EN 3386:2012SIST EN 3386:2012en01-maj-2012SIST EN 3386:2012SLOVENSKI
STANDARD



SIST EN 3386:2012



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 3386
March 2012 ICS 49.030.50 English Version
Aerospace series - Rings retaining, radial mounting, steel, phosphated
Série aérospatiale - Anneaux d'arrêt, à montage radial, en acier, phosphatés
Luft- und Raumfahrt - Sicherungsringe, radial montierbar, aus Stahl, phosphatiert This European Standard was approved by CEN on 24 September 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3386:2012: ESIST EN 3386:2012



EN 3386:2012 (E) 2 Contents Page Foreword . 31 Scope and field of application . 42 Normative references . 43 Required characteristics . 43.1 Configuration — Dimensions — Masses . 43.2 Materials . 43.3 Surface treatment . 44 Designation . 65 Marking. 76 Technical specification . 77 Mounting . 7 SIST EN 3386:2012



EN 3386:2012 (E) 3 Foreword This document (EN 3386:2012) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2012, and conflicting national standards shall be withdrawn at the latest by September 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizati
...