EN ISO 4034:2000
(Main)Hexagon nuts - Product grade C (ISO 4034:1999)
Hexagon nuts - Product grade C (ISO 4034:1999)
Migrated from Progress Sheet (TC Comment) (2000-07-10): UAP of 4 months because //FV has been missed (Res BT C 243/1999) (CC/991125)
Sechskantmuttern - Produktklasse C (ISO 4034:1999)
Diese Internationale Norm legt Eigenschaften von Sechskantmuttern mit Gewinden von M5 bis M64 in Produktklasse C fest. Falls in besonderen Fällen andere Festlegungen als die in dieser Norm aufgeführten benötigt werden, sollten diese den entsprechenden ISO-Normen entnommen werden, z.B. ISO 724, ISO 898-2, ISO 965-1 und ISO 4759-1.
Ecrous hexagonaux - Grade C (ISO 4034:1999)
La présente Norme internationale spécifie les caractéristiques des écrous hexagonaux de filetage M5 à M64 inclus et de grade C. Si, dans des cas particuliers, des spécifications autres que celles figurant dans la présente Norme internationale sont requises, il est recommandé de les prendre dans les Normes internationales existantes, par exemple ISO 724, ISO 898-2, ISO 965-1 et ISO 4759-1.
Šestrobe matice - Razred izdelave C (ISO 4034:1999)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2002
1DGRPHãþD
SIST EN 24034:1996
Šestrobe matice - Razred izdelave C (ISO 4034:1999)
Hexagon nuts - Product grade C (ISO 4034:1999)
Sechskantmuttern - Produktklasse C (ISO 4034:1999)
Ecrous hexagonaux - Grade C (ISO 4034:1999)
Ta slovenski standard je istoveten z: EN ISO 4034:2000
ICS:
21.060.20 Matice Nuts
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL ISO
STANDARD 4034
Third edition
1999-08-15
Hexagon nuts — Product grade C
Écrous hexagonaux — Grade C
A
Reference number
ISO 4034:1999(E)
ISO 4034:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 4034 was prepared by Technical Committee ISO/TC 2, Fasteners.
This third edition cancels and replaces the second edition (ISO 4034:1986) which has been technically revised.
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
ii
© ISO
ISO 4034:1999(E)
Introduction
This International Standard is part of the complete ISO product standard series on external hexagon drive
fasteners. The series comprises:
a) hexagon head bolts (ISO 4014 to ISO 4016 and ISO 8765);
b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);
c) hexagon nuts (ISO 4032 to ISO 4036, ISO 8673 to ISO 8675);
d) hexagon bolts with flange (ISO 4162 and ISO 15071);
e) hexagon nuts with flange (ISO 4161 and ISO 10663);
f) structural bolts and nuts (ISO 4775, ISO 7411 to ISO 7414 and ISO 7417).
iii
INTERNATIONAL STANDARD © ISO ISO 4034:1999(E)
Hexagon nuts — Product grade C
1 Scope
This International Standard specifies the characteristics of hexagon nuts with threads from M5 up to and including M64
and product grade C.
If, in special cases, specifications other than those listed in this International Standard are required, they should be
selected from existing International Standards, for example ISO 724, ISO 898-2, ISO 965-1 and ISO 4759-1.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 225:1983, Fasteners — Bolts, screws, studs and nuts — Symbols and designations of dimensions.
ISO 724:1993,
ISO general-purpose metric screw threads — Basic dimensions.
ISO 898-2:1992, Mechanical properties of fasteners — Part 2: Nuts with specified proof load values — Coarse
thread.
ISO 965-1:1998, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data.
1)
ISO 3269:— , Fasteners — Acceptance inspection.
ISO 4042:1999, Fasteners — Electroplated coatings.
2)
ISO 4759-1:— , Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C.
ISO 8992:1986, Fasteners — General requirements for bolts, screws, studs and nuts.
3)
ISO 10683:— , Fasteners — Non-electrolytically applied zinc flake coatings.
1)
To be published. (Revision of ISO 3269:1988)
2)
To be published. (Revi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.