EN 14219:2003

Hexagon bolts with flange with metric fine pitch thread - Small series (ISO 15072:1999, modified)

This European Standard specifies the characteristics of hexagon bolts with flange with metric fine pitch thread, small series, with product grade A, with nominal thread diameters from 8 mm up to and including 16 mm and property classes 8.8, 9.8, 10.9, 12.9 and A2-70.
If, in special cases, specifications other than those listed in this European Standard are required, they shall be selected from existing European and International Standards, for example ISO 261 ISO 724, ISO 888, EN ISO 898-1, ISO 965-2, EN ISO 3506-1.

Sechskantschrauben mit Flansch mit Feingewinde - Leichte Reihe (ISO 15072:1999, modifiziert)

Diese Europäische Norm legt die Eigenschaften von Sechskantschrauben mit Flansch mit metrischem Feingewinde, leichte Reihe, mit Produktklasse A, mit Gewinde-Nenndurchmessern von 8 mm bis 16 mm und mit Festigkeitsklassen 8.8, 10.9, 12.9 und A2-70 fest.
Wenn, in besonderen Fällen, andere Festlegungen als die in dieser Europäischen Norm benötigt werden, sollten sie den bestehenden Europäischen und Internationalen Normen, z. B. ISO 724, ISO 888,
EN ISO 898-1, ISO 965-2, EN ISO 3506-1, entnommen werden.

Vis à tête hexagonale à embase cylindro-tronçonique à pas fin - Série étroite (ISO 15072:1999, modifiée)

Šestroba glava vijaka s krajcem in metričnim finim navojem - Lahka izvedba (ISO 15072:1999, dopolnjen)

General Information

• Status: Published
• Publication Date: 15-Apr-2003
• ICS: 21.060.10 - Bolts, screws, studs
• Technical Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Drafting Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 13-Apr-2023
• Ref Project: SIST EN 14219:2004 - Hexagon bolts with flange with metric fine pitch thread - Small series (ISO 15072:1999, modified)

Relations

• Corrected By: EN 14219:2003/AC:2007 - Hexagon bolts with flange with metric fine pitch thread - Small series (ISO 15072:1999, modified)
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sechskantschrauben mit Flansch mit Feingewinde - Leichte Reihe (ISO 15072:1999, modifiziert)Vis a tete hexagonale a embase cylindro-tronçonique a pas fin - Série étroite (ISO 15072:1999, modifiée)Hexagon bolts with flange with metric fine pitch thread - Small series (ISO 15072:1999, modified)21.060.10Sorniki, vijaki, stebelni vijakiBolts, screws, studs21.040.10Metrski navojiMetric screw threadsICS:Ta slovenski standard je istoveten z:EN 14219:2003SIST EN 14219:2004en01-januar-2004SIST EN 14219:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14219April 2003ICS 21.060.10English versionHexagon bolts with flange with metric fine pitch thread - Smallseries (ISO 15072:1999, modified)Vis à tête hexagonale à embase cylindro-tronçonique à pasfin - Série étroite (ISO 15072:1999, modifiée)Sechskantschrauben mit Flansch mit Feingewinde - LeichteReihe (ISO 15072:1999, modifiziert)This European Standard was approved by CEN on 14 February 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14219:2003 ESIST EN 14219:2004

Symbols and designations of dimensions are specified in EN 20225.KeyaThe top of the head shall be either full form or indented at the manufacturer's discretion option and shall be either cham-fered or rounded. The minimum diameter of the chamfer circle or start of rounding shall be equal to the maximum width across flats minus 15 %. If the top of the head is indented, the periphery may be rounded.bEdge contour opti
...