EN ISO 2702:2011
(Main)Heat-treated steel tapping screws - Mechanical properties (ISO 2702:2011)
Heat-treated steel tapping screws - Mechanical properties (ISO 2702:2011)
ISO 2702:2011 specifies the characteristics of heat-treated steel tapping screws, with tapping screw thread from ST2,2 to ST9,5 inclusive according to ISO 1478, together with the corresponding test methods.
Wärmebehandelte Blechschrauben aus Stahl - Mechanische Eigenschaften (ISO 2702:2011)
Die vorliegende Internationale Norm legt die Eigenschaften von wärmebehandelten Blechschrauben mit
einem Blechschrauben-Gewinde von ST2,2 bis einschließlich ST9,5 nach ISO 1478 zusammen mit den
zugehörigen Prüfverfahren fest.
Vis à tôle en acier traité thermiquement - Caractéristiques mécaniques (ISO 2702:2011)
L'ISO 2702:2011 spécifie les caractéristiques mécaniques des vis à tôle en acier traitées thermiquement, de filetage ST2,2 à ST9,5 inclus conforme à l'ISO 1478, ainsi que les méthodes d'essai correspondantes.
Toplotno obdelani pločevinski vijaki - Mehanske lastnosti (ISO 2702:2011)
Ta mednarodni standard določa značilnosti toplotno obdelanih pločevinastih vijakov z navojem vijaka od ST 2,2 do vključno ST 9,5 v skladu z ISO 1478, skupaj s pripadajočimi preskusnimi metodami.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2011
1DGRPHãþD
SIST EN ISO 2702:1996
7RSORWQRREGHODQLSORþHYLQVNLYLMDNL0HKDQVNHODVWQRVWL ,62
Heat-treated steel tapping screws - Mechanical properties (ISO 2702:2011)
Wärmebehandelte Blechschrauben aus Stahl - Mechanische Eigenschaften (ISO
2702:2011)
Vis à tôle en acier traité thermiquement - Caractéristiques mécaniques (ISO 2702:2011)
Ta slovenski standard je istoveten z: EN ISO 2702:2011
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 2702
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2011
ICS 21.060.10 Supersedes EN ISO 2702:1994
English Version
Heat-treated steel tapping screws - Mechanical properties (ISO
2702:2011)
Vis à tôle en acier traité thermiquement - Caractéristiques Wärmebehandelte Blechschrauben aus Stahl -
mécaniques (ISO 2702:2011) Mechanische Eigenschaften (ISO 2702:2011)
This European Standard was approved by CEN on 28 April 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2702:2011: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 2702:2011) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2011, and conflicting national standards shall be withdrawn
at the latest by November 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 2702:1994.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 2702:2011 has been approved by CEN as a EN ISO 2702:2011 without any modification.
INTERNATIONAL ISO
STANDARD 2702
Third edition
2011-05-01
Heat-treated steel tapping screws —
Mechanical properties
Vis à tôle en acier traité thermiquement — Caractéristiques mécaniques
Reference number
ISO 2702:2011(E)
©
ISO 2011
ISO 2702:2011(E)
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
ISO 2702:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 2702 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 13, Fasteners with
non-metric thread.
This third edition cancels and replaces the second edition (ISO 2702:1992), which has been technically
revised. In particular, the following modifications have been carried out:
a) the Scope was expended to ST9,5;
b) the maximum core hardness was reduced from 390 HV to 370 HV (see 4.1.3);
c) reference to ISO 898-7 concerning torque-measuring device was added (see 6.2.2).
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.