Low resistance shower outlets for sanitary tapware

This European Standard specifies:
- the dimensional, leaktightness, mechanical and hydraulic characteristics with which shower outlets shall comply;
- the procedures for testing these characteristics.
It applies to shower heads and hand showers of any material used for ablutionary purposes and intended for equipping and supplementing sanitary tapware for baths and showers. They should only be connected downstream of the obturator of the tapware.
Details of pressures and temperatures are given in Table 1.
Table 1 - Conditions of use
   Limits of use   Recommended limits for correct operations
Dynamic pressure   0,01 £ P £ 0 MPa
(0,1 £ P £ 0 bar)   0,02 £ P £ 0,1 MPa
(0,2 £ P £ 1,0 bar)
Temperature   T £ 70 °C   T £ 42 °C
Integral and remote spray attachments incorporated in tapware (e.g. sink and basin mixer taps) are not covered by this standard.
Fittings complying with this Standard can also be used with inlet supply pressures in the range (0,1 to 0,2) MPa (1,0 to 2,0) bar in installations not subject to acoustic requirements.

Brausen für Sanitärarmaturen mit geringem Durchflusswiderstand

Diese Europäische Norm legt Folgendes fest:
- die Maße, die Anforderungen an die Dichtheit, die mechanischen und hydraulischen Anforderungen, denen Brausen ent-sprechen müssen,
- die Prüfverfahren, um diese Anforderungen zu überprüfen.
Sie gilt unabhängig vom verwendeten Material für Brauseköpfe und Handbrausen für die Körperhygiene als Ausrüstung von Sanitärarmaturen in Bädern und Duschen. Sie sollten nur hinter dem Absperrorgan der Sanitärarmatur angeschlossen werden.
Druck- und Temperaturangaben sind in Tabelle 1 enthalten.
Tabelle 1 - Anwendungsbedingungen
   Grenzen der Anwendung   Empfohlener Bereich
der Anwendung
Fließdruck   0,01 MPa £ P £ 0 MPa
(0,1 bar £ P £ 0 bar)   0,02 MPa £ P £ 0,1 MPa
(0,2 bar £ P £ 1,0 bar)
Temperatur   T £ 70 °C   T £ 42 °C
In die Armatur integrierte Auslauf- und Seitenbrausen (z. B. wie bei Spültischmischern) werden in dieser Norm nicht behandelt.
Armaturen nach dieser Norm können auch bei Leitungsdruck zwischen (0,1 bis 0,2) MPa [(1,0 bis 2,0) bar] verwendet werden, wenn sie keinen Geräuschanforderungen unterliegen.

Douches basse pression pour robinetterie sanitaire

La présente Norme européenne spécifie :
¾ les caractéristiques dimensionnelles, d'étanchéité, de comportement mécanique et hydraulique auxquelles doivent répondre les douches ;
¾ les modes opératoires d'essai permettant de contrôler ces caractéristiques.
Elle s'applique aux pommes de douche et aux douchettes à main, quel que soit le matériau utilisé, destinées à équiper et à compléter les robinetteries sanitaires de baignoires ou de douches réservées pour l'hygiène corporelle. Il convient qu'elles ne soient raccordées qu'en aval de l'obturateur de la robinetterie.
Les exigences relatives à la pression et à la température sont données dans le Tableau 1.
Tableau 1 - Conditions d'utilisation
   Limites d'utilisation   Limites recommandées pour un bon fonctionnement
Pression dynamique   0,01 £ P ³ 0 MPa
(0,1 £ P ³ 0 bar)   0,02 £ P £ 0,1 MPa
(0,2 £ P £ 1,0 bar)
Température   T £ 70 °C   T £ 42 °C
Les douchettes intégrées et latérales incorporées dans les robinetteries (par exemple, robinets mitigeurs pour évier et lavabo) ne sont pas couvertes par cette norme.
Les accessoires conformes à la présente norme peuvent également être utilisés avec des pressions d'entrée comprises dans la plage (0,1 à 0,2) MPa, (1,0 à 2,0) bars, dans les installations qui ne sont pas soumises aux exigences acoustiques.

Prhe za sanitarne armature z majhnim notranjim pretočnim uporom

General Information

Status
Withdrawn
Publication Date
16-Sep-2003
Withdrawal Date
26-Feb-2008
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
27-Feb-2008
Completion Date
27-Feb-2008

Relations

Buy Standard

Standard
EN 13904:2004
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Brausen für Sanitärarmaturen mit geringem DurchflusswiderstandDouches basse pression pour robinetterie sanitaireLow resistance shower outlets for sanitary tapware91.140.70Sanitarne napraveSanitary installationsICS:Ta slovenski standard je istoveten z:EN 13904:2003SIST EN 13904:2004en01-maj-2004SIST EN 13904:2004SLOVENSKI
STANDARD



SIST EN 13904:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13904September 2003ICS 91.140.70English versionLow resistance shower outlets for sanitary tapwareDouches basse pression pour robinetterie sanitaireBrausen für Sanitärarmaturen mit geringemDurchflusswiderstandThis European Standard was approved by CEN on 1 August 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13904:2003 ESIST EN 13904:2004



EN 13904:2003 (E)2ContentspageForeword.3Introduction.41Scope.42Normative references.53Terms and definitions.54Classification.55Designation.66Marking.67Materials.67.1Chemical and hygienic requirements.67.2Exposed surface condition and quality of coating.68Dimensional characteristics.68.1General.68.2Connecting dimensions.78.3Special cases.89Leaktightness characteristics.99.1General.99.2Test method.910Mechanical characteristics.910.1General.910.2Mechanical strength.910.3Thermal shock test.1011Hydraulic characteristics.1211.1General.1211.2Test method.1212Maintenance.1413Rotary connection.1513.1General.1513.2Test method.15Annex A (informative)
Low resistance fittings.16Bibliography.18SIST EN 13904:2004



EN 13904:2003 (E)3ForewordThis document (EN 13904:2003) has been prepared by Technical Committee CEN/TC 164 “Water supply”,the secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, at the latest by March 2004, and conflicting national standards shall be withdrawn atthe latest by March 2004.Annex A is informative.This document includes a Bibliography.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark,Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom.SIST EN 13904:2004



EN 13904:2003 (E)4IntroductionIn respect of potential adverse effects on the quality of water intended for human consumption caused by theproduct covered by this standard.1) This standard provides no information as to whether the product may be used without restriction inany of the Member States of the EU or EFTA.2) It should be noted that, while awaiting the adoption of verifiable European criteria, existing nationalregulations concerning the use and/or the characteristics of this product remain in force.This European Standard specifies requirements for ‘low resistance’ shower outlets suitable for use in lowpressure water supply systems as described in informative annex A.Requirements for shower outlets suitable for use in high pressure water supply systems are specified inEN 1112.1 ScopeThis European Standard specifies:¾ the dimensional, leaktightness, mechanical and hydraulic characteristics with which shower outlets shallcomply;¾ the procedures for testing these characteristics.It applies to shower heads and hand showers of any material used for ablutionary purposes and intended forequipping and supplementing sanitary tapware for baths and showers. They should only be connecteddownstream of the obturator of the tapware.Details of pressures and temperatures are given in Table 1.Table 1 — Conditions of useLimits of useRecommended limits for correctoperationsDynamic pressure0,01 £ P £ 0 MPa(0,1 £ P £ 0 bar)0,02 £ P £ 0,1 MPa(0,2 £ P £ 1,0 bar)TemperatureT £ 70 °CT £ 42 °CIntegral and remote spray attachments incorporated in tapware (e.g. sink and basin mixer taps) are notcovered by this standard.Fittings complying with this Standard can also be used with inlet supply pressures in the range (0,1 to 0,2)MPa (1,0 to 2,0) bar in installations not subject to acoustic requirements.SIST EN 13904:2004



EN 13904:2003 (E)52 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications.These normative references are cited at the appropriate places in the text, and the publications are listedhereafter. For dated references, subsequent amendments to or revisions of any of these publications apply tothis European Standard only when incorporated in it by amendment or revision. For undated references thelatest edition of the publication referred to applies (including amendments).EN 248, Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr.EN 13905, Low resistance shower hoses for sanitary tapware.ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions,tolerances and designation.3 Terms and definitionsFor the purposes of this European Standard, the following terms and definitions apply.3.1shower outletdevice for ablutionary purposes which allows water to be emitted in the form of jets or water droplets3.2spray platesdevice with orifices through which water passes and forms a spray of water with separate, definable jets orwater dropletsA spray forming mechanism is a device which generates a spray by other means.3.3shower armcomponent which supports a shower head and connects it to the water supply4 Classificationa) Shower handsetsShower handsets are moveable hand held shower outlets which are connected to the sanitary tapwarevia a shower hose, complying with EN 13905 and can be hung directly on the tapware or on the wall withthe aid of an appropriate support.b) Shower heads and body showersShower heads are fixed overhead shower outlets which direct water onto the user from above.Body showers are shower outlets fixed to the vertical wall and direct water laterally onto the user.SIST EN 13904:2004



EN 13904:2003 (E)65 DesignationShower outlets covered by this Standard are designated by:¾ their type (see clause 4);¾ their connecting thread dimension;¾ their flow rate class (see 11.2.4);¾ reference to this standard: EN 13904.Examples¾ Shower handset, flow rate class H. EN 13904.NOTEFor shower handsets the connecting thread siz
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.