iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

prEN 15266

(Main)

Stainless steel pliable corrugated tubing kits for gas installation pipework with an operating pressure up to 0,2 MPa (2 bar)

Stainless steel pliable corrugated tubing kits for gas installation pipework with an operating pressure up to 0,2 MPa (2 bar)

This European Standard specifies the requirements for material, design, manufacture, testing,
marking and documentation of stainless steel pliable corrugated gas tubing kits for gas installation pipework with a maximum operating pressure (MOP):
— less than or equal to 0,5 bar within a nominal size range from DN 10 to DN 50 (class 1); and
— less than or equal to 2 bar within a nominal size range from DN 10 to DN 25 (class 2).
This document applies to stainless steel pliable corrugated gas tubing kits used for 1st, 2nd and 3rd family gases according to EN437 in residential, commercial and industrial gas installations to be installed outdoors or indoors at a temperature range from - 40 °C to + 60°C.
This document does not apply to:
⎯ pliable tubing without cover;
⎯ corrugated safety metal hose assemblies for connection to moveable appliances
NOTE This document does not cover the installation aspects of stainless steel pliable corrugated gas tubing kits.

Nichtrostende biegbare Wellrohrbausätze für Gasleitungsanlagen mit einem Arbeitsdruck bis 0,2 MPa (2 bar)

Dieses Dokument legt die Anforderungen an Werkstoff, Auslegung, Herstellung, Prüfung, Kennzeichnung und Dokumentation von nichtrostenden biegbaren Wellrohrbausätzen für Gasinstallationsrohrleitungen mit einem maximal zulässigen Druck(PS) fest:
— kleiner oder gleich 0,5bar in einem Nennweitenbereich von DN10 bis DN50 (Klasse1); und
— kleiner oder gleich 2bar in einem Nennweitenbereich von DN10 bis DN25 (Klasse2).
Dieses Dokument gilt für nichtrostende biegbare Wellrohrbausätze für Gase der 1., 2. und 3.Familie (siehe EN437) in häuslichen, gewerblichen und industriellen Gasinstallationen, die im Freien oder in Innenräumen in einem Temperaturbereich von−20°C bis +60°C installiert werden.
Dieses Dokument gilt nicht für:
— biegbare Rohrbausätze ohne Ummantelung;
— gewellte Sicherheits-Schlauchleitungen aus Metall für den Anschluss von beweglichen Geräten.
ANMERKUNG Dieses Dokument behandelt keine Anforderungen bezogen auf den Einbau von nichtrostenden biegbaren Wellrohrbausätzen für Gas.

Kits de tuyaux onduleux pliables en acier inoxydable pour les installations intérieures à gaz avec une pression de service inférieure ou égale à 0,2 MPa (2 bar)

Upogljivi valoviti cevni kompleti iz nerjavnega jekla za plinske napeljave z delovnim tlakom do 0,2 MPa (2 bara)

General Information

Status
Not Published
Publication Date
31-Dec-2024
ICS
23.040.01 - Pipeline components and pipelines in general
Technical Committee
CEN/TC 342 - Metal hoses, hose assemblies, bellows and expansion joints
Drafting Committee
CEN/TC 342/WG 3 - Hose assemblies for gas applications
Current Stage
4060 - Closure of enquiry - Enquiry
Start Date
07-Dec-2023
Due Date
28-Oct-2023
Completion Date
07-Dec-2023
Ref Project
oSIST prEN 15266:2023 - Stainless steel pliable corrugated tubing kits for gas installation pipework with an operating pressure up to 0,2 MPa (2 bar)

Relations

Revises
EN 15266:2007 - Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar
Effective Date
19-Jan-2023

Buy Standard

prEN 15266:2023prEN 15266:2023
PreviousNext
Draft
prEN 15266:2023
English language
46 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 15266:2023
01-december-2023
Upogljivi valoviti cevni kompleti iz nerjavnega jekla za plinske napeljave z
delovnim tlakom do 0,2 MPa (2 bara)
Stainless steel pliable corrugated tubing kits for gas installation pipework with an
operating pressure up to 0,2 MPa (2 bar)
Nichtrostende biegbare Wellrohrbausätze für Gasleitungsanlagen mit einem
Arbeitsdruck bis 0,2 MPa (2 bar)
Kits de tuyaux onduleux pliables en acier inoxydable pour les installations intérieures à
gaz avec une pression de service inférieure ou égale à 0,2 MPa (2 bar)
Ta slovenski standard je istoveten z: prEN 15266
ICS:
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
91.140.40 Sistemi za oskrbo s plinom Gas supply systems
oSIST prEN 15266:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 15266:2023

---------------------- Page: 2 ----------------------
oSIST prEN 15266:2023


DRAFT
EUROPEAN STANDARD
prEN 15266
NORME EUROPÉENNE

EUROPÄISCHE NORM

August 2023
ICS Will supersede EN 15266:2007
English Version

Stainless steel pliable corrugated tubing kits for gas
installation pipework with an operating pressure up to 0,2
MPa (2 bar)
Kits de tuyaux onduleux pliables en acier inoxydable Nichtrostende biegbare Wellrohrbausätze für
pour les installations intérieures à gaz avec une Gasleitungsanlagen mit einem Arbeitsdruck bis 0,2
pression de service inférieure ou égale à 0,2 MPa (2 MPa (2 bar)
bar)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 342.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15266:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 15266:2023
prEN 15266:2023 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and abbreviations . 7
4 Design requirements . 9
4.1 General. 9
4.1.1 Materials . 9
4.1.2 Cover, PLT fittings and PLT supports .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 15266:2007(Main)
Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar
SIST EN 15266:2007

This European Standard specifies the requirements for material, design, manufacture, testing, marking and documentation of stainless steel pliable corrugated gas tubing kits for buildings with a maximum operating pressure (MOP) less than or equal to 0,5 bar and a nominal size range from DN 10 to DN 50.
This document applies to stainless steel pliable corrugated gas tubing kits used for 1st, 2nd and 3rd family gases in residential, commercial and industrial gas installations.
This document does not apply to:
   pliable tubing without cover;
   corrugated safety metal hose assemblies for connection to moveable appliances.
This document does not cover the installation aspects of stainless steel pliable corrugated gas tubing kits.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1594:2024(Main)
Gas infrastructure - Pipelines for maximum operating pressure over 16 bar - Functional requirements
SIST EN 1594:2024

This document describes the functional requirements for pipelines for maximum operating pressure over 16 bar. This document also describes the mechanical requirements for pipework in stations with a maximum operating pressure greater than 16 bar.
NOTE 1   Welding requirements are described in EN 12732. Functional requirements for stations are given in EN 1776, EN 1918-5, EN 12186, and EN 12583.
This document is applicable for transporting gas via onshore high-pressure steel pipeline infrastructures, where the following applies:
-   onshore:
-   from the point where the pipeline first crosses what is normally accepted as battery limit between onshore and offshore, and that is not located within commercial or industrial premises as an integral part of the industrial process on these premises except for any pipelines and facilities supplying such premises;
-   pipeline system with a starting point onshore, also when parts of the pipeline system on the mainland subsequently cross fjords, lakes, etc.
-   high pressure: gas with a maximum operating pressure over 16 bar and a design temperature between −40 °C and 120 °C.
-   steel pipeline infrastructure: infrastructure consisting of pipeline components, such as pipes, valves, couplings and other equipment, restricted to components made of unalloyed or low alloyed carbon steel and joined by welds, flanges or mechanical couplings.
-   gas: non-corrosive natural gas, biomethane gas, hydrogen gas and mixtures of these gases where technical evaluation has ensured that operating conditions or constituents or properties of the gas do not affect the safe operation of the pipeline.
Gas infrastructures covered by this document begin after the gas producer's metering station.
NOTE 2   The functional demarcation of the pipeline system is usually directly after an isolating valve of the installation, but can differ in particular situations. The functional demarcation of the pipeline system is usually located on an isolating valve of the installation, but can differ in particular situations.
A schematic representation of pipelines for gas infrastructure is given in Figure 1.
This document can also be applied to the repurposing of existing pipelines.
[Figure 1 - Schematic representation of pipelines for gas supply over 16 bar]
This document specifies common basic principles for gas infrastructure. Users of this standard are expected to be aware that more detailed national standards and/or code of practice can exist in the CEN member countries.
This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this standard, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737.
CEN/TR 13737 gives:
-   clarification of all legislations/regulations applicable in a member state;
-   if appropriate, more restrictive national requirements;
-   a national contact point for the latest information.

  • Draft
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13480-4:2017/A1:2023(Amendment)
Metallic industrial piping - Part 4: Fabrication and installation
SIST EN 13480-4:2018/A1:2024

This Part of this European Standard specifies the requirements for fabrication and installation of piping systems, including supports, designed in accordance with EN 13480-3:2017.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13480-4:2017/A2:2023(Amendment)
Metallic industrial piping - Part 4: Fabrication and installation
SIST EN 13480-4:2018/A2:2024

This Part of this European Standard specifies the requirements for fabrication and installation of piping systems, including supports, designed in accordance with EN 13480-3:2017.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1566-2:2023(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Assessment of conformity
SIST-TS CEN/TS 1566-2:2023

This document gives guidance for specifying requirements for the AoC of compounds/formulations, products, joints and assemblies in accordance with the applicable part of EN 1566 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 1566 1 (see European foreword), this document is applicable to solid-wall piping systems made of chlorinated poly(vinyl chloride) (PVC C) intended to be used for or soil and waste discharge systems (low and high temperature):
-   inside buildings (application area code "B");
-   for both inside buildings and buried in ground within the building structure (application area code "BD").

  • Technical specification
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1455-2:2023(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 2: Assessment of conformity
SIST-TS CEN/TS 1455-2:2023

This document gives guidance for specifying requirements for the AoC of compounds/formulation, products, joints and assemblies in accordance with the applicable part of EN 1455 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 1455-1 (see European foreword), this document is applicable to solid wall piping systems made of acrylonitrile-butadiene-styrene (ABS) intended to be used for soil and waste discharge (low and high temperature):
-   inside buildings (application area code "B");
-   both inside buildings and buried in ground within the building structure (application area code "BD").

  • Technical specification
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1401-1:2019+A1:2023(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1401-1:2019+A1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC U) piping systems in the field of non-pressure underground drainage and sewerage:
- buried in ground outside the building structure (application area code "U"), and
- both buried in ground, within the building structure and outside the building (application area code "UD").
NOTE 1   The intended use is reflected in the marking of products by "U" or "UD".
It also specifies the test parameters for the test methods referred to in this document.
NOTE 2   Multilayer pipes with different formulations throughout the wall and foamed core pipes are covered by EN 13476-2 [1].
This document covers a range of nominal sizes, a range of pipes and fittings series and a range of stiffness classes and gives recommendations concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It is applicable to PVC U pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 16.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15001-2:2023(Main)
Gas supply systems - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 2: Detailed functional requirements for commissioning, operation and maintenance
SIST EN 15001-2:2023

This European Standard specifies detailed functional requirements for the commissioning, operation and maintenance of
-   industrial gas installations and assemblies with an operating pressure greater than 0,5 bar and of
-   non-industrial gas installations (residential and commercial) with an operating pressure greater than 5 bar,
starting from the outlet of the network operator’s point of delivery up to the inlet connection to the gas appliance; normally the inlet isolation valve. This European Standard also covers the pipework to the inlet connection of a gas appliance that is not included within the scope of the appliance standard.
NOTE   The use of the term installation and pipework is interchangeable.
Apart from the exceptions stated below, this standard applies to gas installations operating at ambient temperatures between -20 °C and 40 °C and operating pressures up to and including 60 bar. For operating conditions outside these limitations, reference should additionally be made to EN 13480 for metallic pipework.
For industrial gas installations up to and including 0,5 bar and for non-industrial (residential and commercial) gas installations up to and including 5 bar EN 1775 applies.
For gas installations that do not fall within the scope of EN 1775 or other European Standards, this European Standard applies.
In this European Standard, the term "gas" refers to combustible gases, which are gaseous at 15 °C and 1 013 mbar absolute atmospheric pressure. These gases are commonly referred to as manufactured gas, natural gas or Liquefied Petroleum Gas (LPG). They are also referred to as first, second or third family gases as classified in Table 1 of EN 437:2003+A1:2009. The given values are considered as normal conditions for all volumes given in this standard.
This European Standard is applicable to installation pipework for the carriage of:
-   processed, non-toxic and non-corrosive natural gas according to EN 437:2003+A1:2009 and EN 16726 -Gas infrastructure - Quality of gas - Group H”,
-   vaporized LNG,
-   biomethane, complying with EN 16723-1,
-   vaporized LNG.
NOTE   The specification of vaporized LNG is equal to that of natural gas as classified in EN 437:2003+A1:2009.
This European Standard does not cover pipework for hydrogen rich gases that fall outside the definitions within EN 437:2003+A1:2009. LPG storage vessels (including all ancillaries fitted directly to storage vessels) are excluded. Also excluded are LPG installations and sections of LPG installations operating at vapour pressure (e.g. between the storage vessel and its pressure regulator).
In this European Standard, all pressures are gauge pressures unless otherwise stated.
This European Standard specifies common basic principles for gas supply systems. Users of this European Standard should be aware that more detailed national standards and/or code of practice may exist in the CEN member countries.
This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
For gas installations within the scope of this standard, national legislation and regulations have to be taken into account.
Functional requirements for design, selection of materials, construction, inspection and testing of industrial gas installations and assemblies with an operating pressure greater than 0,5 bar and of gas installations greater than 5 bar in buildings and areas intended for residential, commercial, public and mixed uses are described in EN 15001-1.
Generally, additional safety precautions may be necessary where non odorized gas is used. For non-industrial purposes, the gas should be odorized.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15001-1:2023(Main)
Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing
SIST EN 15001-1:2023

This European Standard specifies detailed functional requirements for the design, selection of materials, construction, inspection and testing of:
-   industrial gas installation pipework and assemblies with an operating pressure greater than 0,5 bar; and
-   non-industrial gas installation pipework (residential and commercial) with an operating pressure greater than 5 bar in buildings;
starting from the outlet of the network operator’s point of delivery up to the inlet connection to the gas appliance; normally the inlet isolation valve. This standard also covers the pipework to the inlet connection of a gas appliance that is not included within the scope of the appliance standard.
NOTE 1   The use of the term installation and pipework is interchangeable.
Apart from the exceptions stated below, this standard applies to gas installations operating at ambient temperatures between −20 °C and 40 °C and operating pressures up to and including 60 bar. For operating conditions outside these limitations, reference should additionally be made to EN 13480 (all parts) for metallic pipework.
For industrial gas installations up to and including 0,5 bar and for non-industrial (residential and commercial) gas installations up to and including 5 bar in buildings, EN 1775 applies.
For gas installations that do not fall within the scope of EN 1775 or other European Standards, this standard applies.
In this European Standard, the term “gas“ refers to combustible gases, which are gaseous at 15 °C and 1 013 mbar absolute atmospheric pressure (normal conditions). These gases are commonly referred to as manufactured gas, natural gas or Liquefied Petroleum Gas (LPG). They are also referred to as first, second or third family gases as classified in EN 437:2003+A1:2009, Table 1. The given values are considered as normal conditions for all volumes given in this standard.
This European Standard is applicable to installation pipework for the carriage of:
-   processed, non-toxic and non-corrosive natural gas according to EN 437:2003+A1:2009 and EN 16726 "Gas infrastructure - Quality of gas - Group H";
-   vaporized LPG;
-   biomethane, complying with EN 16723 1;
-   vaporized LNG.
NOTE 2   The specification of vaporized LNG is equal to that of natural gas as classified in EN 437:2003+A1:2009.
This European Standard does not cover pipework for hydrogen rich gases that fall outside the definitions within EN 437:2003+A1:2009.
LPG storage vessels (including all ancillaries fitted directly to storage vessels) are excluded. Also excluded are LPG installations and sections of LPG installations operating at vapour pressure in the liquid state (e.g. between the storage vessel and any pressure regulator).
In this standard, all pressures are gauge pressures unless otherwise stated.
This standard has been harmonized to address the essential safety requirements of the Pressure Equipment Directive (PED, 2014/68/EU [formerly 97/23/EC]) relevant for the joining of gas installation pipework (assemblies) falling within the scope of the PED. These are listed in Annex ZA. However, "this Directive does not cover the assembly of pressure equipment on the site and under the responsibility of the user, as in the case of industrial installations" (PED, Preamble, 7th recital, last paragraph).
Although in this respect, the standard takes into account the essential safety requirements of the PED, no inference can be drawn from this as to whether or not the installation or parts of the installation falls within the scope of the PED. Reference should therefore be made to the PED and relevant national legislation.
This European Standard specifies common basic principles for gas supply systems. Users of this European Standard should be aware (...)

  • Standard
    131 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13480-3:2017/A5:2022(Amendment)
Metallic industrial piping - Part 3: Design and calculation
SIST EN 13480-3:2018/A5:2023

This Part of this European Standard specifies the design and calculation of industrial metallic piping systems, including supports, covered by EN 13480

  • Amendment
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day