EN 13180:2001

Ventilation for buildings - Ductwork - Dimensions and mechanical requirements for flexible ducts

This standard specifies requirements and test methods for the technical characteristics of flexible ducts used in ventilation and air conditioning installations in buildings for human occupancy.
This standard identifies the following parameters which shall be tested or inspected:
- dimensions and tolerances;
- mechanical resistance.
Acoustic, thermal, reaction to fire, and pressure loss properties of flexible ducts are not covered in this standard.

Lüftung von Gebäuden - Luftleitungen - Maße und mechanische Anforderungen für flexible Luftleitungen

Diese Norm legt Anforderungen und Prüfverfahren für die technischen Kennwerte flexibler Luftleitungen fest, die in Lüftungs- und Klimaanlagen in Gebäuden für den Aufenthalt von Menschen verwendet werden.
Diese Norm definiert die folgenden Parameter, die geprüft oder untersucht werden müssen:
¾ Maße und zulässige Abweichungen;
¾ mechanische Widerstandsfähigkeit.
Akustische, thermische und Druckverlusteigenschaften sowie Brandverhalten flexibler Luftleitungen werden in dieser Norm nicht behandelt.

Ventilation des bâtiments - Réseau de conduits - Dimensions et prescriptions mécaniques pour les conduits flexibles

La présente norme spécifie les prescriptions et les méthodes d'essai relatives aux caractéristiques techniques des conduits flexibles utilisés dans les installations de ventilation et de conditionnement d'air dans les bâtiments occupés par des personnes.
La présente norme identifie les paramètres suivants devant être soumis à essai ou contrôlés :
¾ dimensions et tolérances ;
¾ résistance mécanique.
Les propriétés acoustiques, thermiques, de résistance au feu et de perte de pression des conduits flexibles ne sont pas couvertes par la présente norme.

Prezračevanje stavb - Razvod zraka - Mere in mehanske zahteve za gibke kanale

General Information

• Status: Published
• Publication Date: 13-Nov-2001
• Withdrawal Date: 30-May-2002
• ICS: 91.140.30 - Ventilation and air-conditioning systems
• Technical Committee: CEN/TC 156 - Ventilation for buildings
• Drafting Committee: CEN/TC 156/WG 3 - Ductwork
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 16-May-2024
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Ref Project: SIST EN 13180:2002 - Ventilation for buildings - Ductwork - Dimensions and mechanical requirements for flexible ducts

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Lüftung von Gebäuden - Luftleitungen - Maße und mechanische Anforderungen für flexible LuftleitungenVentilation des bâtiments - Réseau de conduits - Dimensions et prescriptions mécaniques pour les conduits flexiblesVentilation for buildings - Ductwork - Dimensions and mechanical requirements for flexible ducts91.140.30VLVWHPLVentilation and air-conditioningICS:Ta slovenski standard je istoveten z:EN 13180:2001SIST EN 13180:2002en01-maj-2002SIST EN 13180:2002SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13180November 2001ICS 91.140.30English versionVentilation for buildings - Ductwork - Dimensions andmechanical requirements for flexible ductsVentilation des bâtiments - Réseau de conduits -Dimensions et prescriptions mécaniques pour les conduitsflexiblesLüftung von Gebäuden - Luftleitungen - Maße undmechanische Anforderungen für flexible LuftleitungenThis European Standard was approved by CEN on 29 September 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13180:2001 ESIST EN 13180:2002

Example of a test sheet.16Bibliography.17SIST EN 13180:2002

air ducts –Requirements forstrength andleakageFlangesSheet metalair ducts withrectangularcross section-DimensionsMeasurementof duct surfaceareaRequirements forductworkcomponentsto facilitatemaintenanceDetermination ofmechanical energylossFlexibleductsDuctwork made ofinsulation ductboardsFigure 1
Position of EN 13180 in the field of mechanical building servicesSIST EN 13180:2002

Nominal diameters and deviationsNominal diameter dDeviationsmmmmClass AClass B6380+ 1+ 3100
0125150160200+ 2+ 4250
0300315355400450+ 3+ 650000560630NOTE
Figures in bold indicate recommended sizes in accordance with EN 1506Where a nominal diameter other than those given in Table 1 is specified by the client, the deviationsused shall be those applicable to the nearest smaller nominal diameter given in Table 1.3.2 Ducts with non-circular cross sectionThe nominal dimensions and tolerances shall be as specified by the manufacturer.SIST EN 13180:2002
...