Anodizing of aluminium and its alloys - Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in acid solution(s) (ISO 3210:2017)

ISO 3210:2017 specifies methods of assessing the quality of sealed anodic oxidation coatings on aluminium and its alloys by measurement of the loss of mass after immersion in acid solution(s).
It consists of the following two methods.
-      Method 1: Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in a phosphoric acid based solution without prior acid treatment.
-      Method 2: Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in a phosphoric acid based solution with prior acid treatment.
Method 1 is applicable to anodic oxidation coatings intended for decorative or protective purposes or where resistance to staining is important.
Method 2 is applicable to anodic oxidation coatings intended for outdoor architectural purposes. For less severe applications, Method 1 can be more suitable.
The methods are not applicable to the following:
-      hard-type anodic oxidation coatings which normally are not sealed;
-      anodic oxidation coatings that have been sealed only in dichromate solutions;
-      anodic oxidation coatings produced in chromic acid solutions;
-      anodic oxidation coatings that have undergone treatment to render them hydrophobic.
NOTE 1    The methods assess the quality of hydrothermal sealing applied to anodized aluminium. They can be appropriate for other sealing methods.
NOTE 2    The methods are destructive and can serve as reference methods in case of doubt or dispute regarding the results of the test for loss of absorptive power (see ISO 2143) or the measurement of admittance (see ISO 2931).

Anodisieren von Aluminium und Aluminiumlegierungen - Prüfung der Qualität von verdichteten, anodisch erzeugten Oxidschichten durch Bestimmung des Masseverlustes nach Eintauchen in Säure-Lösung(en) (ISO 3210:2017)

Dieses Dokument legt Verfahren zur Prüfung der Qualität verdichteter, anodisch erzeugter Oxidschichten auf Aluminium und Aluminiumlegierungen durch Bestimmung des Masseverlustes nach Eintauchen in Säure-Lösung(en) fest.
Es besteht aus den folgenden zwei Verfahren:
- Verfahren 1: Bewertung der Qualität verdichteter, anodisch erzeugter Oxidschichten durch Bestimmung des Masseverlustes nach Eintauchen in eine Phosphorsäure-Lösung ohne vorherige Säurebehandlung.
- Verfahren 2: Bewertung der Qualität verdichteter, anodisch erzeugter Oxidschichten durch Bestimmung des Masseverlustes nach Eintauchen in eine Phosphorsäure-Lösung mit vorheriger Säurebehandlung.
Verfahren 1 ist auf anodisch aufgebrachte Oxidschichten anwendbar, die für dekorative Zwecke oder zum Schutz vorgesehen sind oder bei denen die Beständigkeit gegen Fleckenbildung wesentlich ist.
Verfahren 2 ist auf anodisch aufgebrachte Oxidschichten anwendbar, die für Architekturanwendungen im Freien vorgesehen sind. Für weniger stark belastete Anwendungen kann das Verfahren 1 geeigneter sein.
Die Verfahren sind nicht anwendbar auf:
- Oxidschichten, die nach Hartanodisationsverfahren erzeugt wurden und üblicherweise nicht verdichtet sind;
- anodisch erzeugte Oxidschichten, die nur in Dichromat-Lösung verdichtet wurden;
- anodisch erzeugte Oxidschichten, die in Chromsäure-Lösung erzeugt wurden;
- anodisch erzeugte Oxidschichten, die einer hydrophobierenden Behandlung unterzogen wurden.
ANMERKUNG 1 Die Verfahren bewerten die Qualität der hydrothermalen Versiegelung von anodisiertem Aluminium. Sie können für andere Versiegelungsverfahren geeignet sein.
ANMERKUNG 2 Die Verfahren sind nicht zerstörungsfrei und können in Zweifels- oder Streitfällen als Schiedsver-fahren für die Ergebnisse der Prüfung der Anfärbbarkeit (siehe ISO 2143) oder der Messung des Scheinleitwertes (siehe ISO 2931) angewandt werden.

Anodisation de l'aluminium et de ses alliages - Évaluation de la qualité des couches anodiques colmatées par mesurage de la perte de masse après immersion en solution(s) acide(s) (ISO 3210:2017)

L'ISO 3210 :2017 spécifie des méthodes d'évaluation de la qualité des couches anodiques colmatées sur aluminium et alliages d'aluminium par mesurage de la perte de masse après immersion en solution(s) acide(s).
Il comprend les deux méthodes suivantes:
-      Méthode 1: Évaluation de la qualité des couches anodiques colmatées par mesurage de la perte de masse après immersion dans une solution à base d'acide phosphorique, sans traitement acide préalable;
-      Méthode 2: Évaluation de la qualité des couches anodiques colmatées par mesurage de la perte de masse après immersion dans une solution à base d'acide phosphorique, avec traitement acide préalable.
La méthode 1 s'applique aux couches anodiques utilisées à des fins décoratives ou de protection ou lorsque la résistance aux taches est un facteur important.
La méthode 2 s'applique aux couches anodiques utilisées à des fins architecturales en extérieur. Pour des applications moins critiques, la méthode 1 peut se révéler plus adaptée.
Les méthodes ne sont pas applicables:
-      aux couches anodiques dures qui, normalement, ne sont pas colmatées;
-      aux couches anodiques qui ont été colmatées uniquement en solutions bichromatées;
-      aux couches anodiques produites dans des solutions d'acide chromique;
-      aux couches anodiques qui ont subi un traitement d'imperméabilisation.
NOTE 1    Les méthodes évaluent la qualité du colmatage hydrothermique appliqué à l'aluminium anodisé. Elles peuvent être appropriées pour d'autres méthodes de colmatage.
NOTE 2    Les méthodes sont destructives et peuvent servir de méthodes de référence en cas de doute ou de contestation sur les résultats des essais de perte de pouvoir absorbant (voir l'ISO 2143) ou de mesurage de l'admittance (voir l'ISO 2931).

Anodizacija aluminija in njegovih zlitin - Ocena kakovosti zatesnjenih anodno oksidiranih plasti z merjenjem izgube mase po raztapljanju v kislih raztopinah (ISO 3210:2017)

Ta dokument določa metode ocenjevanje kakovosti zatesnjenih anodno oksidiranih plasti
na aluminiju in njegovih zlitinah z merjenjem izgube mase po raztapljanju v kislih raztopinah.
Vključuje v nadaljevanju opisani metodi.
– 1. metoda: Ocena kakovosti zatesnjenih anodno oksidiranih plasti z merjenjem izgube mase po raztapljanju v raztopini na osnovi fosforne kisline brez predhodne obdelave s kislino.
– 2. metoda: Ocena kakovosti zatesnjenih anodno oksidiranih plasti z merjenjem izgube mase po raztapljanju v raztopini na osnovi fosforne kisline s predhodno obdelavo s kislino.
1. metoda se uporablja za anodno oksidirane plasti, predvidene za dekorativne ali zaščitne namene, ali kadar je pomembna odpornost na obarvanje.
2. metoda se uporablja za anodno oksidirane plasti, predvidene za arhitekturne namene na prostem. Za primere uporabe v manj zahtevnih pogojih je morda primernejša 1. metoda.
Metodi se ne uporabljata za:
– trde anodno oksidirane plasti, ki običajno niso zatesnjene;
– anodno oksidirane plasti, ki so bile zatesnjene izključno v raztopinah dikromata;
– anodno oksidirane plasti, pridobljene v raztopinah s kromovo kislino;
– anodno oksidirane plasti, ki so bile obdelane za namene hidrofobnosti.
OPOMBA 1: Metodi omogočata oceno kakovosti hidrotermalne zatesnitve, ki se uporablja za anodiziran aluminij. Primerni sta lahko za druge metode tesnjenja.
OPOMBA 2: Metodi sta porušitveni in se lahko v primeru dvoma ali spora glede rezultatov
preskušanja za izgubo absorpcijske moči (glej ISO 2143) ali meritev sprejema (glej ISO 2931) uporabljata kot referenčni metodi.

General Information

Status
Published
Publication Date
05-Dec-2017
Withdrawal Date
29-Jun-2018
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
06-Dec-2017
Completion Date
06-Dec-2017

Relations

Buy Standard

Standard
EN ISO 3210:2018
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 3210:2018
01-februar-2018
1DGRPHãþD
SIST EN ISO 3210:2010
Anodizacija aluminija in njegovih zlitin - Ocena kakovosti zatesnjenih anodno
oksidiranih plasti z merjenjem izgube mase po raztapljanju v kislih raztopinah (ISO
3210:2017)
AAnodizing of aluminium and its alloys - Assessment of quality of sealed anodic
oxidation coatings by measurement of the loss of mass after immersion in acid solution
(s) (ISO 3210:2017)
Anodisieren von Aluminium und Aluminiumlegierungen - Prüfung der Qualität von
verdichteten, anodisch erzeugten Oxidschichten durch Bestimmung des Masseverlustes
nach Eintauchen in Säure-Lösung(en) (ISO 3210:2017)
Anodisation de l'aluminium et de ses alliages - Évaluation de la qualité des couches
anodiques colmatées par mesurage de la perte de masse après immersion en solution
(s) acide(s) (ISO 3210:2017)
Ta slovenski standard je istoveten z: EN ISO 3210:2017
ICS:
25.220.20 Površinska obdelava Surface treatment
77.120.10 Aluminij in aluminijeve zlitine Aluminium and aluminium
alloys
SIST EN ISO 3210:2018 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 3210:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 3210:2018


EN ISO 3210
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2017
EUROPÄISCHE NORM
ICS 25.220.20 Supersedes EN ISO 3210:2010
English Version

Anodizing of aluminium and its alloys - Assessment of
quality of sealed anodic oxidation coatings by
measurement of the loss of mass after immersion in acid
solution(s) (ISO 3210:2017)
Anodisation de l'aluminium et de ses alliages - Anodisieren von Aluminium und
Évaluation de la qualité des couches anodiques Aluminiumlegierungen - Prüfung der Qualität von
colmatées par mesurage de la perte de masse après verdichteten, anodisch erzeugten Oxidschichten durch
immersion en solution(s) acide(s) (ISO 3210:2017) Bestimmung des Masseverlustes nach Eintauchen in
Säure-Lösung(en) (ISO 3210:2017)
This European Standard was approved by CEN on 22 October 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3210:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 3210:2018
EN ISO 3210:2017 (E)
Contents Page
European foreword . 3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 3210:2018
EN ISO 3210:2017 (E)
European foreword
This document (EN ISO 3210:2017) has been prepared by Technical Committee ISO/TC 79 “Light
metals and their alloys” in collaboration with Technical Committee CEN/TC 132 “Aluminium and
aluminium alloys” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2018, and conflicting national standards shall be
withdrawn at the latest by June 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3210:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finlan
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.