EN ISO 898-1:2009

Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2009)

ISO 898-1:2009 specifies mechanical and physical properties of bolts, screws and studs made of carbon steel and alloy steel when tested at an ambient temperature range of 10 °C to 35 °C. Fasteners — the term used when bolts, screws and studs are considered all together — that conform to its requirements are evaluated at that ambient temperature range. Information is given on fasteners that do not retain the specified mechanical and physical properties at elevated temperatures and/or lower temperatures.
ISO 898-1:2009 excludes certain fasteners that do not fulfil its tensile or torsional requirements because the geometry of their heads reduce the shear area in the head compared to the stress area in the thread. These include fasteners having a low head, with or without external driving feature, a low round or cylindrical head with internal driving feature or a countersunk head with internal driving feature (see 8.2).
It is applicable to bolts, screws and studs made of carbon steel or alloy steel, having a triangular ISO metric screw thread according to ISO 68-1, with a coarse pitch thread M1,6 to M39, and fine pitch thread M8´1 to M39´3, with diameter/pitch combinations according to ISO 261 and ISO 262, having thread tolerances according to ISO 965-1, ISO 965-2 and ISO 965-4.
It is not applicable to set screws and similar threaded fasteners not under tensile stresses (see ISO 898-5).
It does not specify requirements for such properties as weldability, corrosion resistance, resistance to shear stress, torque/clamp force performance, or fatigue resistance.

Mechanische Eigenschaften von Verbindungselementen aus Kohlenstoffstahl und legiertem Stahl - Teil 1: Schrauben mit festgelegten Festigkeitsklassen - Regelgewinde und Feingewinde (ISO 898-1:2009)

Dieser Teil von ISO 898 legt mechanische und physikalische Eigenschaften von Schrauben aus Kohlenstoffstahl
und legiertem Stahl fest, die in einem Bereich der Umgebungstemperatur von 10 °C und 35 °C geprüft
werden.
Schrauben (im Englischen als „fastener“ bezeichnet, wenn gleichzeitig „bolts“, „screws“ und „studs“ angesprochen
werden), die den Anforderungen dieser Norm entsprechen, werden in diesem Bereich der
Umgebungstemperatur bewertet. Es kann sein, dass sie die festgelegten mechanischen und physikalischen
Eigenschaften bei höheren Temperaturen (siehe Angaben in Anhang B) und/oder niedrigeren Temperaturen
nicht beibehalten.
ANMERKUNG 1 Schrauben, die den Anforderungen dieses Teils von ISO 898 entsprechen, werden für Anwendungen
in dem Bereich zwischen −50 °C und +150 °C eingesetzt. Anwender sollten für Temperaturen außerhalb des Bereiches
von −50 °C und +150 °C sowie bis zu einer Höchsttemperatur von +300 °C einen erfahrenen Metallurgen für Verbindungselemente
konsultieren, um die geeignete Wahl für die vorgesehene Anwendung zu treffen.
ANMERKUNG 2 Informationen zur Auswahl und Anwendung von Stählen für den Gebrauch bei niedrigeren und
höheren Temperaturen sind z. B. in EN 10269, ASTM F2281 und in ASTM A 320/A 320M enthalten.
Bestimmte Schrauben erfüllen möglicherweise nicht die in diesem Teil von ISO 898 festgelegten Anforderungen
an die Belastbarkeit unter Zug oder Torsion, weil wegen der Kopfgeometrie die Scherfläche im Kopf
gegenüber dem Spannungsquerschnitt im Gewinde verkleinert ist. Dies betrifft Schrauben mit niedrigen
Köpfen, mit oder ohne Außenantrieb, mit niedrigen Rund- oder Zylinderköpfen mit Innenantrieb oder mit
Senkköpfen mit Innenantrieb (siehe 8.2).
Dieser Teil von ISO 898 gilt für Schrauben:
a) aus Kohlenstoffstahl und legiertem Stahl;
b) mit Metrischem ISO-Gewinde nach ISO 68-1;
c) mit Regelgewinde M1,6 bis M39 und Feingewinde M8×1 bis M39×3;
d) mit Durchmesser-Steigungs-Kombinationen nach ISO 261 und ISO 262;

Caractéristiques mécaniques des éléments de fixation en acier au carbone et en acier allié - Partie 1: Vis, goujons et tiges filetées de classes de qualité spécifiées - Filetages à pas gros et filetages à pas fin (ISO 898-1:2009, Version corrigée 2009-07-15)

L'ISO 898-1:2009 spécifie les caractéristiques mécaniques et physiques des vis, goujons et tiges filetées en acier au carbone et en acier allié, essayés dans la plage de température ambiante de 10 °C à 35 °C. Les éléments de fixation — terme utilisé lorsque les vis, goujons et tiges filetées sont considérés dans leur ensemble — conformes aux exigences de la présente partie de l'ISO 898 sont évalués uniquement dans cette plage de températures ambiantes. Des informations sont données pour les éléments de fixation qui ne conservent pas les caractéristiques mécaniques et physiques spécifiées à des températures élevées et/ou inférieures.
Certains éléments de fixation peuvent ne pas satisfaire aux exigences de l'ISO 898-1:2009 concernant la résistance à la traction ou à la torsion, en raison de la géométrie de la tête (section cisaillée dans la tête inférieure à la section résistante dans le filetage). Ceux-ci comprennent les éléments de fixation à tête réduite, avec ou sans entraînement externe, à tête bombée plate et cylindrique basse avec entraînement interne ou à tête fraisée avec entraînement interne.
La présente partie de l'ISO 898 s'applique aux vis, goujons et tiges filetées en acier au carbone ou en acier allié, à filetage métrique ISO triangulaire conforme à l'ISO 68‑1, de filetage M1,6 à M39 (pour les pas gros) et de filetage M8 x 1 à M39 x 3 (pour les pas fins), de combinaisons diamètre/pas conformes à l'ISO 261 et à l'ISO 262, de tolérance de filetage conforme à l'ISO 965‑1, ISO 965‑2 et ISO 965‑4.
Elle ne s'applique pas aux vis sans tête et éléments de fixation filetés similaires non soumis à des contraintes de traction (voir l'ISO 898‑5).
Elle ne spécifie aucune exigence pour des caractéristiques telles que la soudabilité, la résistance à la corrosion, la résistance au cisaillement, la performance couple/tension, ou la résistance à la fatigue.

Mehanske lastnosti veznih elementov iz ogljikovega in legiranega jekla - 1. del: Vijaki s specificiranim trdnostnim razredom - Grobi in fini navoj (ISO 898-1:2009)

General Information

• Status: Withdrawn
• Publication Date: 31-Mar-2009
• Withdrawal Date: 22-Jan-2013
• ICS: 21.060.10 - Bolts, screws, studs
• Technical Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Drafting Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 23-Jan-2013
• Completion Date: 23-Jan-2013
• Directive: 87/404/EEC - Simple pressure vessels
• Mandate: M/BC/CEN/89/2 - Standardization mandate to CEN concerning supporting standards in the context of pressure vessels
• Ref Project: SIST EN ISO 898-1:2009 - Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2009)

Relations

• Replaces: EN ISO 898-1:1999 - Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs (ISO 898-1:1999)
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 898-1:2013 - Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
• Effective Date: 08-Jun-2022
• Amended By: EN ISO 898-1:2009/prA1 - Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2009/DAM 1:2010)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-junij-2009
1DGRPHãþD
SIST EN ISO 898-1:2001
Mehanske lastnosti veznih elementov iz ogljikovega in legiranega jekla - 1. del:
Vijaki s specificiranim trdnostnim razredom - Grobi in fini navoj (ISO 898-1:2009)
Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts,
screws and studs with specified property classes - Coarse thread and fine pitch thread
(ISO 898-1:2009)
Mechanische Eigenschaften von Verbindungselementen aus Kohlenstoffstahl und
legiertem Stahl - Teil 1: Schrauben mit festgelegten Festigkeitsklassen - Regelgewinde
und Feingewinde (ISO 898-1:2009)
Caractéristiques mécaniques des éléments de fixation en acier au carbone et en acier
allié - Partie 1: Vis, goujons et tiges filetées de classes de qualité spécifiées - Filetages à
pas gros et filetages à pas fin (ISO 898-1:2009)
Ta slovenski standard je istoveten z: EN ISO 898-1:2009
ICS:
21.040.01 Navoji na splošno Screw threads in general
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 898-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2009
ICS 21.060.10 Supersedes EN ISO 898-1:1999
English Version
Mechanical properties of fasteners made of carbon steel and
alloy steel - Part 1: Bolts, screws and studs with specified
property classes - Coarse thread and fine pitch thread (ISO 898-
1:2009)
Caractéristiques mécaniques des éléments de fixation en Mechanische Eigenschaften von Verbindungselementen
acier au carbone et en acier allié - Partie 1: Vis, goujons et aus Kohlenstoffstahl und legiertem Stahl - Teil 1:
tiges filetées de classes de qualité spécifiées - Filetages à Schrauben mit festgelegten Festigkeitsklassen -
pas gros et filetages à pas fin (ISO 898-1:2009) Regelgewinde und Feingewinde (ISO 898-1:2009)
This European Standard was approved by CEN on 28 February 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 898-1:2009: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
This document (EN ISO 898-1:2009) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at
the latest by October 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 898-1:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 898-1:2009 has been approved by CEN as a EN ISO 898-1:2009 without any modification.

INTERNATIONAL ISO
STANDARD 898-1
Fourth edition
2009-04-01
Mechanical properties of fasteners made
of carbon steel and alloy steel —
Part 1:
Bolts, screws and studs with specified
property classes — Coarse thread and
fine pitch thread
Caractéristiques mécaniques des éléments de fixation en acier au
carbone et en acier allié —
Partie 1: Vis, goujons et tiges filetées de classes de qualité
spécifiées — Filetages à pas gros et filetages à pas fin

Reference number
ISO 898-1:2009(E)
©
ISO 2009
ISO 898-1:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved

ISO 898-1:2009(E)
Contents Page
Foreword. iv
1 Scope .1
2 Normative references .2
3 Terms and definitions .3
4 Symbols and abbreviated terms .4
5 Designation system for property classes .5
6 Materials .6
7 Mechanical and physical properties.8
8 Applicability of test methods.12
8.1 General.12
8.2 Loadability of fasteners .12
8.3 Manufacturer's control.13
8.4 Supplier's control .13
8.5 Purchaser's control .13
8.6 Feasible tests for groups of fasteners and machined test pieces .14
9 Test methods.21
9.1 Tensile test under wedge loading of finished bolts and screws (excluding studs) .21
9.2 Tensile test for finished bolts, screws and studs for determination of tensile strength, R .25
m
9.3 Tensile test for full-size bolts, screws and studs for determination of elongation after
fracture, A , and stress at 0,004 8 d non-proportional elongation, R .27
f pf
9.4 Tensile test for bolts and screws not expected to break in free threaded length due to
head design .31
9.5 Tensile test for fasteners with waisted shank .32
9.6 Proof load test for finished bolts, screws and studs.33
9.7 Tensile test for machined test pieces.35
9.8 Head soundness test.38
9.9 Hardness test .39
9.10 Decarburization test .41
9.11 Carburization test .44
9.12 Retempering test.46
9.13 Torsional test .46
9.14 Impact test for machined test pieces .47
9.15 Surface discontinuity inspection .48
10 Marking .48
10.1 General.48
10.2 Manufacturer's identification mark .48
10.3 Marking and designation of fasteners with full loadability .49
10.4 Marking and designation of fasteners which, because of their geometry, have reduced
loadability .53
10.5 Marking of packages .53
Annex A (informative) Relation between tensile strength and elongation after fracture .54
Annex B (informative) Influence of elevated temperatures on mechanical properties of fasteners .55
Annex C (informative) Elongation after fracture for full-size fasteners, Α .56
f
Bibliography .57
ISO 898-1:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies c
...