EN ISO 2440:1999/A1:2010
(Amendment)Flexible and rigid cellular polymeric materials - Accelerated ageing tests - Amendment 1 (ISO 2440:1997/Amd 1:2010)
Flexible and rigid cellular polymeric materials - Accelerated ageing tests - Amendment 1 (ISO 2440:1997/Amd 1:2010)
Specifies, for flexible and rigid cellular polymeric materials, laboratory procedures which are intended to imitate the effects of naturally occuring reactions such as oxidation or hydrolysis by humidity. The physical properties of interest are measured before and after the applicaton of the specified treatments. Test conditions are only given for open cellylar latex, both open- and cell polyurethane foams, and closed-cell polyolefin foams. Conditions for other materials will be added as required. The effect of the ageing procedures of any of the physical properties of the material may be examined, but those normally tested are either the elongation and tensile properties, or the compression or identation hardness properties. These tests do not necessarily correlate either with service behaviour or with ageing by exposure to light.
Weich- und Hartschaumstoffe- Schnellalterungsprüfung - Änderung 1 (ISO 2440:1997/Amd 1:2010)
Matériaux polymères alvéolaires souples et rigides - Essais de vieillissement accéléré - Amendement 1 (ISO 2440:1997/Amd 1:2010)
Polimerni materiali - Mehke in trde pene - Preskus s pospešenim staranjem - Dopolnilo A1 (ISO 2440:1997/Amd 1:2010)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2014
Polimerni materiali - Mehke in trde pene - Preskus s pospešenim staranjem -
Dopolnilo A1 (ISO 2440:1997/Amd 1:2010)
Flexible and rigid cellular polymeric materials - Accelerated ageing tests - Amendment 1
(ISO 2440:1997/Amd 1:2010)
Weich- und Hartschaumstoffe- Schnellalterungsprüfung - Änderung 1 (ISO
2440:1997/Amd 1:2010)
Matériaux polymères alvéolaires souples et rigides - Essais de vieillissement accéléré -
Amendement 1 (ISO 2440:1997/Amd 1:2010)
Ta slovenski standard je istoveten z: EN ISO 2440:1999/A1:2010
ICS:
83.100 Penjeni polimeri Cellular materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 2440:1999/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2010
ICS 83.100
English Version
Flexible and rigid cellular polymeric materials - Accelerated
ageing tests - Amendment 1 (ISO 2440:1997/Amd 1:2010)
Matériaux polymères alvéolaires souples et rigides - Essais Weich- und Hartschaumstoffe- Schnellalterungsprüfung -
de vieillissement accéléré - Amendement 1 (ISO Änderung 1 (ISO 2440:1997/Amd 1:2010)
2440:1997/Amd 1:2010)
This amendment A1 modifies the European Standard EN ISO 2440:1999; it was approved by CEN on 6 February 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2440:1999/A1:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 2440:1999/A1:2010) has been prepared by Technical Committee ISO/TC 45 "Rubber
and rubber products" in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of
which is held by NBN.
This Amendment to the European Standard EN ISO 2440:1999 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by August 2010, and
conflicting national standards shall be withdrawn at the latest by August 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 2440:1997/Amd 1:2010 has been approved by CEN as a EN ISO 2440:1999/A1:2010 without
any modification.
INTERNATIONAL ISO
STANDARD 2440
Third edition
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.