Aggregates for mortar

This European Standard specifies the properties of aggregates obtained by processing natural, manufactured or recycled materials and mixtures of these aggregates for use in mortars, renders and screeds, e.g.
a)   masonry mortar,
b)   floor/screed mortar,
c)   surfacing of internal walls (plastering mortar),
d)   rendering of external walls,
e)   special bedding materials,
f)   repair mortar,
g)   grouts,
for buildings, roads and civil engineering works.
It covers aggregates having an oven dried particle density greater than 1,50 Mg/m3 (2 000 kg/m3). It also covers recycled aggregate with densities between 1,50 Mg/m3 (1 500 kg/m3) and 2,00 Mg/m3 (2 000 kg/m3).
A list of the source materials that have been considered and are within the scope of this standard is given in Annex A (normative)
Requirements for the evaluation of conformity of the products to this European Standard are given in FprEN 16236.
It incorporates a general requirement that aggregates will not release any dangerous substances in excess of the maximum permitted levels specified in a relevant European Standard for the material or permitted in the national regulations of the member state of destination (see Note 3).
The Tables in this standard include categories that are common across the four main aggregate standards: EN 12620, EN 13043, EN 13139 and EN 13242. Not all of these categories are appropriate for aggregates for use in mortars, renders and screeds. Those categories, which are appropriate for mortar, are shown grey shaded.
NOTE 1   Aggregates used in construction should comply with all the relevant requirements of the appropriate European Standards for aggregates. These standards include comprehensive and specific requirements for natural aggregates, iron and steel making slag and recycled aggregates, dealing with, for example, the stability of certain basalts, the expansion of certain slags and the constitution of recycled aggregates.
For materials from some other secondary sources, however, work is ongoing and the requirements are incomplete. In the meantime such materials, when placed on the market as aggregates, will comply fully with this standard but may also be required to comply with specific relevant additional requirements at the place of use. Additional characteristics and requirements may be specified on a case-by-case basis depending upon experience of use of the product, and defined in specific contractual documents.
NOTE 2   Properties for lightweight aggregates are specified in EN 13055-1.
NOTE 3    Requirements for the declaration of the potential of aggregates to release regulated dangerous substances are currently under development. Until such time as these are finalized, attention should be paid to requirements at the place of use.

Gesteinskörnungen für Mörtel

Diese Europäische Norm legt die Eigenschaften von Gesteinskörnungen fest, die durch Aufbereitung natürlicher, industriell hergestellter oder rezyklierter Materialien und ihrer Mischungen gewonnen werden und für die Verwendung in Mörtel, Putzmörtel und Estrichen für Gebäude, Straßen und Ingenieurbauten vorgesehen sind, z. B.:
a)   Mauermörtel;
b)   Estrichmörtel;
c)   Innenputzmörtel;
d)   Außenputzmörtel;
e)   besondere Vergussmörtel;
f)   Reparaturmörtel;
g)   Einpressmörtel.
Sie deckt Gesteinskörnungen mit einer Kornrohdichte nach Trocknung im Wärmeschrank größer als 2,00 Mg/m3 (2 000 kg/m3) ab. Die Norm deckt ebenfalls rezyklierte Gesteinskörnungen mit einer Rohdichte größer als 1,50 Mg/m3 (1 500 kg/m3) ab.
Anhang A (normativ) enthält ein Verzeichnis der berücksichtigten Ausgangsmaterialien, die im Anwen-dungsbereich dieser Europäischen Norm liegen.
Anforderungen an die Bewertung der Konformität von Produkten nach dieser Europäischen Norm sind in EN 16236 enthalten.
Die Norm enthält die allgemeine Anforderung, dass die Freisetzung gefährlicher Stoffe aus Gesteinskörnungen die maximal zulässigen Grenzwerte, die in der einschlägigen Europäischen Norm für das Material festgelegt sind bzw. die nach den nationalen Bestimmungen des Bestimmungsmitgliedstaats zulässig sind, nicht übersteigen darf.
Die Tabellen in dieser Norm enthalten Kategorien, die in allen vier Hauptnormen für Gesteinskörnungen festgelegt sind: EN 12620, EN 13043, EN 13139 und EN 13242. Nicht alle Kategorien sind für Gesteinskörnungen zur Verwendung in Mörtel, Putzmörtel und Estrichen geeignet.
Die grau hinterlegten Kategorien, Anmerkungen, Kommentare, usw. sollten nicht für Gesteinskörnungen in Mörtel verwendet werden.
Gesteinskörnungen im Bauwesen sollten mit allen einschlägigen Anforderungen der jeweiligen Europäischen Normen für Gesteinskörnungen übereinstimmen. Diese Normen enthalten umfassende und spezifische Anforderungen an natürliche Gesteinskörnungen, Hochofenstück- und Stahlwerksschlacken und rezyklierte Gesteinskörnungen, die sich zum Beispiel mit der Raumbeständigkeit einiger Basalte, der Volumenzunahme bestimmter Schlacken und der Zusammensetzung von rezyklierten Gesteinskörnungen befassen.
Die Arbeiten an Festlegungen für Materialien aus weiteren sekundären Quellen sind jedoch noch nicht abgeschlossen und die Anforderungen sind unvollständig. In der Zwischenzeit sollten solche Materialien, sofern sie als Gesteinskörnungen in Verkehr gebracht werden, den Anforderungen dieser Norm voll entsprechen. Unter Umständen müssen sie aber auch zusätzliche spezifische Anforderungen, die am Verwendungsort gelten, erfüllen. Abhängig von den Erfahrungen mit der Anwendung des Produkts dürfen im Einzelfall zusätzliche Eigenschaften und Anforderungen festgelegt werden und in den spezifischen Vertragsunterlagen definiert werden.
ANMERKUNG    Anforderungen an leichte Gesteinskörnungen sind in prEN 13055 festgelegt.
Zurzeit werden Anforderungen an die Angabe des Potenzials von Gesteinskörnungen, gesetzlich geregelte gefährliche Stoffe freizusetzen, erarbeitet. Bis zur Fertigstellung dieser Anforderungen sollten die Anforderungen am Verwendungsort beachtet werden.

Granulats pour mortiers

Cette Norme Européenne spécifie les caractéristiques des granulats élaborés à partir de matériaux naturels, artificiels ou recyclés et de mélanges de ces granulats utilisés dans les mortiers, les mortiers d'enduit et les mortiers pour chapes, par exemple :
a)   mortier de maçonnerie ;
b)   mortier pour chape ou plancher ;
c)   surfaçage des parois intérieures (mortier pour enduit) ;
d)   enduit des parois extérieures ;
e)   matériaux spéciaux de scellement ;
f)   mortier pour réparation ;
g)   mortier de coulis,
pour les bâtiments, routes et travaux de génie civil.
Elle s'applique aux granulats dont la masse volumique réelle après séchage à l'étuve est supérieure à 2,00 Mg/m3 (2 000 kg/m3). Elle s'applique également aux granulats recyclés dont la masse volumique réelle est supérieure à 1,50 Mg/m3 (1 500 kg/m3).
Une liste des origines des matériaux qui ont été prises en considération et relèvent du domaine d'application de la présente norme est donnée à l'Annexe A (normative).
Les exigences relatives à l’évaluation de la conformité sont spécifiées dans l’EN 16236.
La présente norme intègre une exigence générale stipulant que les granulats ne doivent dégager aucune substance dangereuse dont les valeurs d'émission dépassent les niveaux maximaux admissibles spécifiés dans une Norme européenne pertinente pour le matériau ou dans la réglementation nationale de l'Etat membre de destination.
Les tableaux de la présente norme contiennent des catégories qui sont communes aux quatre principales normes relatives aux granulats : EN 12620, EN 13043, EN 13139 et EN 13242. Ces catégories ne sont pas toutes appropriées pour un usage des granulats dans les mortiers, les mortiers d'enduit et les mortiers pour chapes.
Les catégories, notes, commentaires, etc. qui sont grisés ne devraient pas être utilisées pour les applications dans les mortiers.
Les granulats utilisés dans la construction doivent respecter toutes les exigences des Normes européennes concernées. Ces dernières contiennent les exigences générales et particulières relatives aux granulats naturels, au laitier de haut fourneau et d'aciérie et aux granulats recyclés, et traitent par exemple de la stabilité de certains basaltes, de l'expansion de certains laitiers et de la composition des granulats recyclés.
Cependant, pour les matériaux provenant d’autres sources secondaires, les travaux sont en cours et les exigences sont incomplètes. En attendant, il convient que ces matériaux, lorsqu'ils sont mis sur le marché en tant que granulats, respectent pleinement la présente norme, mais ils peuvent aussi devoir se conformer à des exigences complémentaires spécifiques pertinentes sur le lieu d'utilisation. Des caractéristiques et des exigences complémentaires peuvent être spécifiées au cas par cas, en fonction de l'expérience acquise à l'usage du produit, et définies dans des documents contractuels spécifiques.
NOTE   Les caractéristiques des granulats légers sont spécifiées dans le prEN 13055.
Les exigences relatives à la déclaration du potentiel des granulats à relarguer des substances dangereuses réglementées sont actuellement en cours d'élaboration. Tant qu'elles ne sont pas finalisées, il convient de tenir compte des exigences en vigueur sur le lieu d'utilisation.

Agregati za malte

Ta evropski standard določa lastnosti agregatov, pridobljenih z obdelavo naravnih, umetnih ali recikliranih materialov, in zmesi teh agregatov za uporabo v maltah, ometih in estrihih, npr.
a) malta za zidanje:
b) malta za estrihe/talna malta;
c) notranji ometi,
d) zunanji ometi,
e) posebni materiali za podlago,
f) malta za popravila,
g) injekcijske mase
za stavbe, ceste in gradbene inženirske objekte.
Zajema agregate s prostorninsko maso sušenih zrn, večjo od 2,00 mg/m3 (2000 kg/m3). Zajema tudi agregate s prostorninsko maso, večjo od 1,50 mg/m3 (1500 kg/m3). Seznam obravnavanih izvornih materialov, ki določa materiale, vključene v predmet tega standarda, je naveden v dodatku A (normativni). Zahteve za vrednotenje skladnosti izdelkov s tem evropskim standardom so navedene v standardu EN 16236. Vključuje splošno zahtevo o tem, da agregati ne smejo oddajati nobenih nevarnih snovi v količinah, ki so večje od največjih dovoljenih količin v ustreznem evropskem standardu za materiale ali v nacionalni zakonodaji države članice. Razpredelnice v tem standardu vključujejo kategorije, ki so skupne vsem štirim glavnim standardom za agregate: EN 12620, EN 13043, EN 13139 in EN 13242. Nekatere od teh kategorij niso primerne za agregate za uporabo v maltah, ometih in estrihih. Kategorije, opombe, komentarji itd. v sivi barvi se ne smejo uporabljati v maltah. Agregati, ki se uporabljajo pri konstrukcijah, morajo izpolnjevati ustrezne zahteve primernih evropskih standardov za agregate. Ti standardi vključujejo celovite in posebne zahteve za naravne agregate, žlindro, nastalo pri pridobivanju železa in jekla, in reciklirane agregate ter obravnavajo na primer stabilnost nekaterih bazaltov, raztezek nekaterih vrst žlindre in sestavo recikliranih agregatov. Za materiale iz nekaterih drugih sekundarnih virov oblikovanje standardov še poteka in so zahteve nepopolne. Kadar so taki materiali dani na tržišče kot agregati, morajo v celoti ustrezati temu standardu in morajo biti morda skladni tudi s posebnimi ustreznimi dodatnimi zahtevami, ki veljajo na območju uporabe. Dodatne značilnosti in zahteve se lahko določijo za vsak posamezen primer glede na izkušnje pri uporabi izdelka in so opredeljene v posebnih pogodbenih dokumentih. OPOMBA Zahteve za lahke agregate so določene v standardu prEN 13055. Zahteve za izjavo o kapaciteti agregatov za izpust reguliranih nevarnih snovi so v pripravi. Dokler te zahteve niso dokončno oblikovane, je treba upoštevati zahteve na območju uporabe.

General Information

Status
Withdrawn
Publication Date
30-Apr-2013
Withdrawal Date
11-Dec-2013
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
12-Dec-2013
Completion Date
12-Dec-2013

Relations

Effective Date
08-May-2013
Effective Date
13-Feb-2013
Effective Date
22-Dec-2008

Buy Standard

Standard
EN 13139:2013
English language
40 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
k FprEN 13139:2011
English language
38 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Agregati za malteGesteinskörnungen für MörtelGranulats pour mortiersAggregates for mortar91.100.15Mineralni materiali in izdelkiMineral materials and productsICS:Ta slovenski standard je istoveten z:EN 13139:2013SIST EN 13139:2013en,fr,de01-julij-2013SIST EN 13139:2013SLOVENSKI
STANDARDSIST EN 13139:2002/AC:2004SIST EN 13139:20021DGRPHãþD



SIST EN 13139:2013



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13139
May 2013 ICS 91.100.15 Supersedes EN 13139:2002English Version
Aggregates for mortar
Granulats pour mortiers
Gesteinskörnungen für Mörtel This European Standard was approved by CEN on 5 September 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13139:2013: ESIST EN 13139:2013



EN 13139:2013 (E) 2 Contents page
Foreword . 3 1 Scope . 5 2 Normative references . 6 3 Terms and definitions . 6 4 Geometrical requirements . 8 5 Physical requirements . 17 6 Chemical requirements . 18 7 Durability . 20 8 Evaluation of conformity . 22 9 Designation and description . 22 10 Marking and labelling . 22 Annex A (normative)
Source materials considered in the development of EN 13139 and their status in respect of the scope of the standard . 23 Annex B (informative)
Guidance on the description of coarseness/fineness of aggregates for mortars . 26 Annex C (informative)
Guidance on the effects of some chemical constituents of aggregates on the mortar in which they are incorporated . 27 Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or other provisions of EU Directives . 29 Bibliography .
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Agregati za malteGesteinskörnungen für MörtelGranulats pour mortiersAggregates for mortar91.100.15Mineralni materiali in izdelkiMineral materials and productsICS:Ta slovenski standard je istoveten z:FprEN 13139kSIST FprEN 13139:2011en,fr,de01-maj-2011kSIST FprEN 13139:2011SLOVENSKI
STANDARD



kSIST FprEN 13139:2011



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN 13139
March 2011 ICS 91.100.15 Will supersede EN 13139:2002English Version
Aggregates for mortar
Granulats pour mortiers
Gesteinskörnungen für Mörtel This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 154.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN 13139:2011: EkSIST FprEN 13139:2011



FprEN 13139:2011 (E) 2 Contents page
Foreword . 31 Scope . 42 Normative references . 53 Terms and definitions . 54 Geometrical requirements . 75 Physical requirements . 156 Chemical requirements . 167 Durability . 188 Evaluation of conformity . 199 Designation and description . 2010 Marking and labelling . 20Annex A (normative)
Source materials considered in the development of EN 13139 and their status in respect of the Scope of the standard . 21Annex B (informative)
Guidance on the description of coarseness/fineness of aggregates for mortars . 24Annex C Guidance on the effects of some chemical constituents of aggregates on the mortar in which they are incorporated . 25Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or other provisions of EU Directives .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.