Devices to prevent pollution by backflow of potable water - Hose Union anti-vacuum valves - DN 15 to DN 25 inclusive Family H, type B and type D - General technical specification

This document specifies:
a)   the field of application;
b)   the requirements of hose union anti vacuum valves;
c)   dimensional and physio-chemical properties, and properties of general hydraulic, mechanical and acoustic design of hose union anti-vacuum valves of nominal sizes DN 15 up to and including DN 25;
d)   marking and technical product information.
This document specifies the characteristics of hose union anti-vacuum valves of nominal size DN 15 up to and including DN 25 that are suitable for use in drinking water systems at pressures up to and including 1 MPa (10 bar) and temperatures up to and including 65 °C and for 1 h at 90 °C.
HB protects against back siphonage only and is installed in vertical downward flow position.
HD protects against back flow and is installed in vertical downward flow position.
HB and HD anti-vacuum valves are for installation exclusively at the connecting point between stop valve and hose in vertical downward flow position.

Sicherungseinrichtungen zum Schutz des Trinkwassers gegen Verschmutzung durch Rückfließen - Rohrbelüfter für Schlauchanschlüsse - DN 15 bis DN 25, Familie H, Typ B und Typ D - Allgemeine technische Bestimmungen

Dieses Dokument legt Folgendes fest:
a) den Anwendungsbereich;
b) die Anforderungen an Rohrbelüfter für Schlauchanschlüsse;
c) maßliche, physikalisch-chemische Eigenschaften und Eigenschaften allgemeiner hydraulischer, mechanischer und akustischer Art von Rohrbelüftern für Schlauchanschlüsse der Nennweiten DN 15 bis einschließlich DN 25;
d) Kennzeichung und technische Produktinformation.
Dieses Dokument legt die Eigenschaften von Rohrbelüftern für Schlauchanschlüsse der Nennweiten DN 15 bis einschließlich DN 25 fest, die für die Verwendung in Trinkwasserversorgungsanlagen bei Drücken bis einschließlich 1 MPa (10 bar) und Temperaturen bis einschließlich 65 °C sowie für 1 h bei 90 °C geeignet sind.
Rohrbelüfter HB schützen nur gegen Rücksaugen und sollten senkrecht nach unten installiert werden.
Rohrbelüfter HD schützen gegen Rücksaugen und sollten senkrecht nach unten installiert werden.
Rohrbelüfter HB und HD sind nur für den Einbau am Anschluss zwischen Vorabsperrung (Absperrventil) und Schlauch bestimmt, senkrecht nach unten gerichtet.

Dispositifs de protection contre la pollution par retour de l’eau potable - Soupapes anti-vide d’extrémité - DN 15 à DN 25 inclus Famille H, type B et type D - Spécifications techniques générales

Le présent document spécifie :
a)   le domaine d’application ;
b)   les exigences relatives aux soupapes anti-vide d’extrémité ;
c)   les caractéristiques dimensionnelles, physico-chimiques, ainsi que les caractéristiques de conception hydraulique, mécanique et acoustique générales des soupapes anti-vide d’extrémité de dimension nominale DN 15 à DN 25 inclus ;
d)   le marquage et les informations techniques sur le produit.
Le présent document spécifie les caractéristiques des soupapes anti-vide d’extrémité de dimension nominale DN 15 à DN 25 inclus, qui conviennent à une utilisation dans des réseaux d’eau potable à des pressions jusqu’à 1 MPa (10 bar) et des températures jusqu’à 65 °C et durant 1 h à 90 °C.
La soupape HB protège uniquement contre le siphonnage et est installée de façon à assurer un écoulement vertical descendant.
La soupape HD protège contre le retour d’eau et est installée de façon à assurer un écoulement vertical descendant.
Les soupapes anti-vide HB et HD sont prévues pour être installées exclusivement au point de raccordement entre le robinet d’arrêt et le flexible de façon à assurer un écoulement vertical descendant.

Naprave za varovanje pred onesnaženjem pitne vode zaradi povratnega toka - Ventili za preprečevanje podtlaka v pregibnih ceveh - DN 15 do DN 25, vključno z družino H, vrsto B in vrsto D - Splošna tehnična specifikacija

General Information

Status
Published
Publication Date
29-Sep-2020
Withdrawal Date
30-Dec-2020
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
24-Jun-2020
Due Date
15-Nov-2020
Completion Date
24-Jun-2020

Relations

Buy Standard

Standard
EN 15096:2020
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 15096:2020
01-september-2020
Nadomešča:
SIST EN 15096:2009
Naprave za varovanje pred onesnaženjem pitne vode zaradi povratnega toka -
Ventili za preprečevanje podtlaka v pregibnih ceveh - DN 15 do DN 25, vključno z
družino H, vrsto B in vrsto D - Splošna tehnična specifikacija

Devices to prevent pollution by backflow of potable water - Hose Union anti-vacuum

valves - DN 15 to DN 25 inclusive Family H, type B and type D - General technical

specification
Sicherungseinrichtungen zum Schutz des Trinkwassers gegen Verschmutzung durch

Rückfließen - Rohrbelüfter für Schlauchanschlüsse - DN 15 bis DN 25, Familie H, Typ B

und Typ D - Allgemeine technische Bestimmungen

Dispositifs de protection contre la pollution de l'eau potable par retour - Soupapes anti-

vide d'extrémité - DN 15 à DN 25 inclus Famille H, type B et type D - Spécification

technique générale
Ta slovenski standard je istoveten z: EN 15096:2020
ICS:
13.060.20 Pitna voda Drinking water
23.060.01 Ventili na splošno Valves in general
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN 15096:2020 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 15096:2020
---------------------- Page: 2 ----------------------
SIST EN 15096:2020
EN 15096
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2020
EUROPÄISCHE NORM
ICS 13.060.20; 23.060.01 Supersedes EN 15096:2008
English Version
Devices to prevent pollution by backflow of potable water
- Hose Union anti-vacuum valves - DN 15 to DN 25
inclusive Family H, type B and type D - General technical
specification

Dispositifs de protection contre la pollution par retour Sicherungseinrichtungen zum Schutz des Trinkwassers

de l'eau potable - Soupapes anti-vide d'extrémité - DN gegen Verschmutzung durch Rückfließen -

15 à DN 25 inclus Famille H, type B et type D - Rohrbelüfter für Schlauchanschlüsse - DN 15 bis DN

Spécifications techniques générales 25, Familie H, Typ B und Typ D - Allgemeine technische

Bestimmungen
This European Standard was approved by CEN on 24 May 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15096:2020 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 15096:2020
EN 15096:2020 (E)
Contents Page

European foreword ....................................................................................................................................................... 4

Introduction .................................................................................................................................................................... 5

1 Scope .................................................................................................................................................................... 6

2 Normative references .................................................................................................................................... 6

3 Terms and definitions ................................................................................................................................... 7

4 Nominal size ...................................................................................................................................................... 7

5 Designation........................................................................................................................................................ 8

6 Marking and technical product information ......................................................................................... 8

6.1 General ................................................................................................................................................................ 8

6.2 Marking ............................................................................................................................................................... 8

6.3 Technical product information .................................................................................................................. 9

7 Graphic symbol ................................................................................................................................................ 9

8 General design characteristics ................................................................................................................... 9

8.1 Design principle ............................................................................................................................................... 9

8.2 Connections .................................................................................................................................................... 11

8.3 Check valve ..................................................................................................................................................... 11

9 Materials and surface finishes ................................................................................................................. 11

9.1 General ............................................................................................................................................................. 11

9.2 Materials .......................................................................................................................................................... 11

9.3 Corrosion resistance ................................................................................................................................... 11

10 Characteristics and tests ........................................................................................................................... 12

10.1 General ............................................................................................................................................................. 12

10.2 Test sequence ................................................................................................................................................ 12

10.3 Visual verification (stage 1) ..................................................................................................................... 12

10.3.1 Procedure........................................................................................................................................................ 12

10.3.2 Verification of the dimensional requirements of air inlets .......................................................... 13

10.4 Bending moment and tightness test of HB element (stage 2) ...................................................... 13

10.4.1 Tightness test equipment .......................................................................................................................... 13

10.4.2 Bending moment, mechanical strength of the body and static high pressure leak

tightness test .................................................................................................................................................. 14

10.4.3 Static low pressure tightness test .......................................................................................................... 14

10.4.4 Dynamic low pressure tightness test .................................................................................................... 15

10.5 Flow rate (stage 3) ....................................................................................................................................... 15

10.5.1 Flow rate testing equipment .................................................................................................................... 15

10.5.2 Procedure........................................................................................................................................................ 16

10.5.3 Requirement .................................................................................................................................................. 16

10.6 Opening pressure test (stage 4) .............................................................................................................. 16

10.6.1 Test equipment ............................................................................................................................................. 16

10.6.2 Procedure........................................................................................................................................................ 17

10.6.3 Requirements ................................................................................................................................................ 17

10.7 Endurance test (stage 5) ............................................................................................................................ 17

10.7.1 General ............................................................................................................................................................. 17

10.7.2 Endurance test equipment ........................................................................................................................ 18

---------------------- Page: 4 ----------------------
SIST EN 15096:2020
EN 15096:2020 (E)

10.7.3 Dynamic test (test device 1) ..................................................................................................................... 18

10.7.4 Endurance test; static, low pressure (test device 2) ....................................................................... 19

10.7.5 Endurance testing; 14 days (test device 3) .......................................................................................... 20

10.8 Vacuum test (stage 6) .................................................................................................................................. 21

10.8.1 General ............................................................................................................................................................. 21

10.8.2 Backsyphonage test ..................................................................................................................................... 21

10.8.3 Efficiency of the air inlets .......................................................................................................................... 22

10.9 Tightness test (stage 7) .............................................................................................................................. 22

11 Acoustic characteristics ............................................................................................................................. 22

11.1 General ............................................................................................................................................................. 22

11.2 Procedure ........................................................................................................................................................ 22

11.2.1 Mounting and operating conditions....................................................................................................... 22

11.2.2 Test methods .................................................................................................................................................. 22

11.3 Test criteria .................................................................................................................................................... 23

11.3.1 Expression of the results ............................................................................................................................ 23

11.3.2 Noise classification ....................................................................................................................................... 23

Annex A (informative) Tests and sampling ...................................................................................................... 24

---------------------- Page: 5 ----------------------
SIST EN 15096:2020
EN 15096:2020 (E)
European foreword

This document (EN 15096:2020) has been prepared by Technical Committee CEN/TC 164 “Water

supply”, the secretariat of which is held by AFNOR.

This document shall be given the status of a national standard, either by publication of an identical text

or by endorsement, at the latest by December 2020, and conflicting national standards shall be

withdrawn at the latest by December 2020.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 15096:2008.
In comparison with the previous edition, the following changes have been made:
a) title changed;
b) scope of application revised;
c) Clause 2 updated;
d) nominal size range in Clause 4 restricted;
e) Clause 9 adapted.
This document has been developed in reference with EN 1717.

According to the CEN-CENELEC Internal Regulations, the national standards organisations of the

following countries are bound to implement this document: Austria, Belgium, Bulgaria, Croatia, Cyprus,

Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North

Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United

Kingdom.
---------------------- Page: 6 ----------------------
SIST EN 15096:2020
EN 15096:2020 (E)
Introduction

In respect of potential adverse effects on the quality of water intended for human consumption caused

by the product covered by this document:

a) this document provides no information as to whether the product may be used without restriction in

any of the Member States of the EU or EFTA;

b) it should be noted that, while awaiting the adoption of verifiable European criteria, existing national

regulations concerning the use and/or the characteristics of this product remain in force.

---------------------- Page: 7 ----------------------
SIST EN 15096:2020
EN 15096:2020 (E)
1 Scope
This document specifies:
a) the field of application;
b) the requirements of hose union anti vacuum valves;

c) dimensional and physio-chemical properties, and properties of general hydraulic, mechanical and

acoustic design of hose union anti-vacuum valves of nominal sizes DN 15 up to and including DN 25;

d) marking and technical product information.

This document specifies the characteristics of hose union anti-vacuum valves of nominal size DN 15 up

to and including DN 25 that are suitable for use in drinking water systems at pressures up to and

including 1 MPa (10 bar) and temperatures up to and including 65 °C and for 1 h at 90 °C.

HB protects against back siphonage only and is installed in vertical downward flow position.

HD protects against back flow and is installed in vertical downward flow position.

HB and HD anti-vacuum valves are for installation exclusively at the connecting point between stop valve

and hose in vertical downward flow position.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

EN 1717:2000, Protection against pollution of potable water in water installations and general

requirements of devices to prevent pollution by backflow

EN 13959, Anti-pollution check valves - DN 6 to DN 250 inclusive family E, type A, B, C and D

EN ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions,

tolerances and designation (ISO 228-1)

EN ISO 3822-1, Acoustics - Laboratory tests on noise emission from appliances and equipment used in water

supply installations - Part 1: Method of measurement (ISO 3822-1)

EN ISO 3822-3, Acoustics - Laboratory tests on noise emission from appliances and equipment used in water

supply installations - Part 3: Mounting and operating conditions for in-line valves and appliances (ISO 3822-

EN ISO 5167-1, Measurement of fluid flow by means of pressure differential devices inserted in circular

cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1)

EN ISO 6509-1, Corrosion of metals and alloys - Determination of dezincification resistance of copper alloys

with zinc - Part 1: Test method (ISO 6509-1)

EN 248, Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr

---------------------- Page: 8 ----------------------
SIST EN 15096:2020
EN 15096:2020 (E)
3 Terms and definitions

For the purposes of this document, the terms and definitions in EN 1717:2000 and the following apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
3.1
hose union anti-vacuum valve HB

valve equipped with air inlet ports, which are closed at zero flow and when water flows in the intended

direction above atmospheric pressure

Note 1 to entry: The air inlets are opened if there is subatmospheric pressure at the water inlet and closed to be

watertight again when the supply lines are back to at least atmospheric pressure

Note 2 to entry: For the purpose of this standard, “hose union anti-vacuum valve(s)” are hereafter referred to as

“device(s)”
3.2
hose union anti-vacuum valve HD

valve HB with integrated check valve EB located upstream (monoblock/combined products e.g. frost

taps)

Note 1 to entry: For the purpose of this standard, “hose union anti-vacuum valve(s)” are hereafter referred to as

“device(s)”
4 Nominal size

The nominal size of the devices (DN designated) shall correspond to the nominal size of the threaded

inlet connection according to Table 1.
Table 1 — Thread size vs nominal size
Thread size according to
G 1/2 G 3/4 G 1
EN ISO 228-1
DN 15 20 25
---------------------- Page: 9 ----------------------
SIST EN 15096:2020
EN 15096:2020 (E)
5 Designation
The device is designated by:
a) name;
b) family;
c) type;
d) nominal size;
e) its size and type of end connection;
f) the a
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.