EN 4014:2004
(Main)Aerospace series - Inserts, thickwall, self-locking - Design standard
Aerospace series - Inserts, thickwall, self-locking - Design standard
This standard specifies the use and installation hole dimensions for EN standard, self-locking, thickwall inserts and provisions for component salvage, for aerospace applications.
Luft- und Raumfahrt - Gewindeeinsätze, dickwandig, Selbstsichernd - Konstruktionsnorm
Diese Norm legt die Verwendung und Maße von Einbaulöchern für selbstsichernde, dickwandige Gewindeeinsätze nach EN-Normen sowie Vorkehrungen zur Reparatur von Bauteilen für Anwendungen in der Luft und Raumfahrt fest.
Série aérospatiale - Douilles filetées, à paroi renforcée, à freinage interne - Norme de conception
Aerospace series - Inserts, thickwall, self-locking - Design standard
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 4014:2005
01-junij-2005
1DGRPHãþD
SIST EN 4014:2004
Aerospace series - Inserts, thickwall, self-locking - Design standard
Aerospace series - Inserts, thickwall, self-locking - Design standard
Luft- und Raumfahrt - Gewindeeinsätze, dickwandig, Selbstsichernd - Konstruktionsnorm
Série aérospatiale - Douilles filetées, a paroi renforcée, a freinage interne - Norme de
conception
Ta slovenski standard je istoveten z: EN 4014:2004
ICS:
49.030.30 Matice Nuts
SIST EN 4014:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 4014:2005
---------------------- Page: 2 ----------------------
SIST EN 4014:2005
EUROPEAN STANDARD
EN 4014
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2004
ICS 49.030.30 Supersedes EN 4014:2003
English version
Aerospace series - Inserts, thickwall, self-locking - Design
standard
Série aérospatiale - Douilles filetées, à paroi renforcée, à Luft- und Raumfahrt - Gewindeeinsätze, dickwandig,
freinage interne - Norme de conception Selbstsichernd - Konstruktionsnorm
This European Standard was approved by CEN on 11 September 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4014:2004: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 4014:2005
EN 4014:2004 (E)
Contents Page
Foreword.3
1 Scope.4
2 Normative references.4
3 Design.4
4 Use.5
4.1 General.5
4.2 Performance.6
4.3 Installation restrictions.6
5 Required characteristics.7
5.1 Installation hole.7
5.2 Serration.8
6 Installation.9
7 Provisions for component salvage.9
8 Designation.9
9 Indication on drawings.9
9.1 Drawing definition.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.