EN ISO 16283-2:2018

Acoustics - Field measurement of sound insulation in buildings and of building elements - Part 2: Impact sound insulation (ISO 16283-2:2018)

This document specifies procedures to determine the impact sound insulation using sound pressure measurements with an impact source operating on a floor or stairs in a building. These procedures are intended for room volumes in the range from 10 m3 to 250 m3 in the frequency range from 50 Hz to 5 000 Hz. The test results can be used to quantify, assess and compare the impact sound insulation in unfurnished or furnished rooms where the sound field can approximate to a diffuse field.

Akustik - Messung der Schalldämmung in Gebäuden und von Bauteilen am Bau - Teil 2: Trittschalldämmung (ISO 16283-2:2018)

Dieses Dokument legt Verfahren zur Bestimmung der Trittschalldämmung durch Schalldruckmessungen mit einer auf einer Decke oder Treppen in einem Gebäude wirkenden Trittschallquelle fest. Diese Verfahren sind für Raumvolumen im Bereich von 10 m3 bis 250 m3 und den Frequenzbereich von 50 Hz bis 5 000 Hz vorgesehen. Die Prüfergebnisse können genutzt werden, um die Trittschalldämmung in unmöblierten und möblierten Räumen quantitativ zu bestimmen, zu beurteilen und miteinander zu vergleichen, wobei das Schallfeld etwa einem diffusen Schallfeld entsprechen kann.

Acoustique - Mesurage in situ de l'isolation acoustique des bâtiments et des éléments de construction - Partie 2: Isolation des bruits d'impacts (ISO 16283-2:2018)

Le présent document spécifie les modes opératoires permettant de déterminer l'isolation des bruits d'impacts à l'aide de mesurages de la pression acoustique avec une source d'impacts agissant sur un sol ou sur un escalier à l'intérieur d'un bâtiment. Ces modes opératoires s'appliquent aux pièces dont le volume est compris entre 10 m3 et 250 m3 et dont la fréquence est comprise entre 50 Hz et 5 000 Hz. Les résultats des essais peuvent être utilisés pour quantifier, évaluer et comparer l'isolation des bruits d'impacts dans des pièces non meublées ou meublées où le champ acoustique peut être assimilé à un champ diffus.

Akustika - Terenska merjenja zvočne izolirnosti v stavbah in zvočne izolirnosti stavbnih elementov - 2. del: Izolirnost pred udarnim zvokom (ISO 16283-2:2018)

Ta dokument določa postopke za določanje izolirnosti pred udarnim zvokom z meritvami zvočnega tlaka z virom udarnega zvoka v hodnikih ali na stopnicah v stavbi. Ti postopki so namenjeni prostorom s prostornino 10–250 m3 v frekvenčnem območju 50–5000 Hz. Rezultate preskusa je mogoče uporabiti za kvantifikacijo, ovrednotenje in primerjavo izolirnosti pred udarnim zvokom v neopremljenih ali opremljenih prostorih, kjer je zvočno polje lahko podobno razpršenemu polju.

General Information

• Status: Withdrawn
• Publication Date: 07-Aug-2018
• Withdrawal Date: 25-Aug-2020
• ICS: 91.060.30 - Ceilings. Floors. Stairs
• ICS: 91.120.20 - Acoustics in building. Sound insulation
• Technical Committee: CEN/TC 126 - Acoustic properties of building products and of buildings
• Drafting Committee: CEN/TC 126 - Acoustic properties of building products and of buildings
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 26-Aug-2020
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Ref Project: SIST EN ISO 16283-2:2018 - Acoustics - Field measurement of sound insulation in buildings and of building elements - Part 2: Impact sound insulation (ISO 16283-2:2018)

Relations

• Replaces: EN ISO 16283-2:2015 - Acoustics - Field measurement of sound insulation in buildings and of building elements - Part 2: Impact sound insulation (ISO 16283-2:2015)
• Effective Date: 14-Jun-2017
• Replaced By: EN ISO 16283-2:2020 - Acoustics - Field measurement of sound insulation in buildings and of building elements - Part 2: Impact sound insulation (ISO 16283-2:2020)
• Effective Date: 19-Dec-2018

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2018
1DGRPHãþD
SIST EN ISO 16283-2:2016
$NXVWLND7HUHQVNDPHUMHQMD]YRþQHL]ROLUQRVWLYVWDYEDKLQ]YRþQHL]ROLUQRVWL
VWDYEQLKHOHPHQWRYGHO,]ROLUQRVWSUHGXGDUQLP]YRNRP,62
Acoustics - Field measurement of sound insulation in buildings and of building elements -
Part 2: Impact sound insulation (ISO 16283-2:2018)
Akustik - Messung der Schalldämmung in Gebäuden und von Bauteilen am Bau - Teil 2:
Trittschalldämmung (ISO 16283-2:2018)
Acoustique - Mesurage in situ de l'isolation acoustique des bâtiments et des éléments de
construction - Partie 2: Isolation des bruits d'impacts (ISO 16283-2:2018)
Ta slovenski standard je istoveten z: EN ISO 16283-2:2018
ICS:
17.140.01 $NXVWLþQDPHUMHQMDLQ Acoustic measurements and
EODåHQMHKUXSDQDVSORãQR noise abatement in general
91.120.20 $NXVWLNDYVWDYEDK=YRþQD Acoustics in building. Sound
L]RODFLMD insulation
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 16283-2
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2018
EUROPÄISCHE NORM
ICS 91.060.30; 91.120.20 Supersedes EN ISO 16283-2:2015
English Version
Acoustics - Field measurement of sound insulation in
buildings and of building elements - Part 2: Impact sound
insulation (ISO 16283-2:2018)
Acoustique - Mesurage in situ de l'isolation acoustique Akustik - Messung der Schalldämmung in Gebäuden
des bâtiments et des éléments de construction - Partie und von Bauteilen am Bau - Teil 2: Trittschalldämmung
2: Isolation des bruits d'impacts (ISO 16283-2:2018) (ISO 16283-2:2018)
This European Standard was approved by CEN on 9 June 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16283-2:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 16283-2:2018) has been prepared by Technical Committee ISO/TC 43
"Acoustics" in collaboration with Technical Committee CEN/TC 126 “Acoustic properties of building
elements and of buildings” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2019, and conflicting national standards
shall be withdrawn at the latest by February 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 16283-2:2015.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 16283-2:2018 has been approved by CEN as EN ISO 16283-2:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 16283-2
Second edition
2018-05
Acoustics — Field measurement of
sound insulation in buildings and of
building elements —
Part 2:
Impact sound insulation
Acoustique — Mesurage in situ de l'isolation acoustique des
bâtiments et des éléments de construction —
Partie 2: Isolation des bruits d'impacts
Reference number
ISO 16283-2:2018(E)
©
ISO 2018
ISO 16283-2:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 16283-2:2018(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Instrumentation . 5
4.1 General . 5
4.2 Calibration . 5
4.3 Verification . 5
5 Frequency range . 6
5.1 Tapping machine as the impact source . 6
5.2 Rubber ball as the impact source . 6
6 General . 6
7 Default procedure for sound pressure level measurement . 7
7.1 General . 7
7.2 Generation of sound field . 7
7.2.1 General. 7
7.2.2 Impact source positions for the tapping machine as impact source . 7
7.2.3 Impact source positions for the rubber ball as impact source . 8
7.3 Fixed microphone positions for the tapping machine or rubber ball as impact source . 8
7.3.1 General. 8
7.3.2 Number of measurements . 8
7.3.3 Tapping machine operated at more than one position . 8
7.3.4 Rubber ball operated at more than one position . 9
7.4 Mechanized continuously moving microphone for the tapping machine as impact source 9
7.4.1 General. 9
7.4.2 Number of measurements .10
7.4.3 Tapping machine operated at more than one position .10
7.5 Manually scanned microphone for the tapping machine as impact source .10
7.5.1 General.10
7.5.2 Number of measurements .10
7.5.3 Tapping machine operated at more than one position .10
7.5.4 Circle .10
7.5.5 Helix .10
7.5.6 Cylindrical-type . .11
7.5.7 Three semicircles .11
7.6 Minimum distances for microphone positions .12
7.7 Averaging times for the tapping machine as impact source .12
7.7.1 Fixed microphone positions.12
7.7.2 Mechanized continuously moving microphone .13
7.7.3 Manually scanned microphone .13
7.8 Calculation of energy-average sound pressure levels .13
7.8.1 Fixed microphone positions for the tapping machine as impact source .13
7.8.2 Mechanized continuously moving microphone and manually scanned
microphone for the tapping machine as impact source .13
7.8.3 Fixed microphone positions for the rubber ball as impact source .14
8 Low-frequency procedure for sound pressure level measurement for the tapping
machine as impact source .14
8.1 General .14
8.2 Generation of sound field .
...