prEN ISO 3386-1
(Main)Polymeric materials, cellular flexible - Determination of stress-strain characteristics in compression - Part 1: Low-density materials (ISO/DIS 3386-1:2024)
Polymeric materials, cellular flexible - Determination of stress-strain characteristics in compression - Part 1: Low-density materials (ISO/DIS 3386-1:2024)
Covers the determination of material with a density up to 250 kg/m3. It also indicates a method for the calculation of the compression stress value of such materials. The compression stress/strain characteristic is a measure of the load-bearing properties of the material. Two formulas allow to calculate the results. Part 2 refers to high density materials. Constitutes a minor revision of the first edition (ISO 3386/1-1979).
Polymere Materialien, weich-elastische Schaumstoffe - Bestimmung der Druckspannungs-Verformungseigenschaften - Teil 1: Materialien mit niedriger Dichte (ISO/DIS 3386-1:2024)
Matériaux polymères alvéolaires souples - Détermination de la caractéristique de contrainte-déformation relative en compression - Partie 1: Matériaux à basse masse volumique (ISO/DIS 3386-1:2024)
La présente partie de l'ISO 3386 spécifie une méthode de détermination de la caractéristique de contrainte-déformation relative en compression des matériaux polymères alvéolaires souples à basse masse volumique, jusqu'à 250 kg/m3. Elle indique également un mode de calcul de la valeur de la contrainte en compression de tels matériaux. La caractéristique de contrainte-déformation relative en compression est une mesure de l'aptitude du matériau à supporter des charges, mais pas nécessairement des charges de longue durée. La caractéristique de contrainte-déformation relative en compression diffère des caractéristiques de dureté par indentation (déterminées conformément à l'ISO 2439), lesquelles, comme on le sait, sont influencées par l'épaisseur et les caractéristiques de traction du matériau alvéolaire souple soumis à l'essai, par la forme de la plaque de compression et par la forme et les dimensions de l'éprouvette. L'ISO 3386/2 spécifie une méthode pour les maté
Polimerni materiali, mehke pene - Določanje diagrama napetost/raztezek - 1. del: Materiali z nizko gostoto (ISO/DIS 3386-1:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Polimerni materiali, mehke pene - Določanje diagrama napetost/raztezek - 1. del:
Materiali z nizko gostoto (ISO/DIS 3386-1:2024)
Polymeric materials, cellular flexible - Determination of stress-strain characteristics in
compression - Part 1: Low-density materials (ISO/DIS 3386-1:2024)
Polymere Materialien, weich-elastische Schaumstoffe - Bestimmung der
Druckspannungs-Verformungseigenschaften - Teil 1: Materialien mit niedriger Dichte
(ISO/DIS 3386-1:2024)
Matériaux polymères alvéolaires souples - Détermination de la caractéristique de
contrainte-déformation relative en compression - Partie 1: Matériaux à basse masse
volumique (ISO/DIS 3386-1:2024)
Ta slovenski standard je istoveten z: prEN ISO 3386-1
ICS:
83.100 Penjeni polimeri Cellular materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
International
Standard
ISO/DIS 3386-1
ISO/TC 45/SC 4
Polymeric materials, cellular
Secretariat: DSM
flexible — Determination of
Voting begins on:
stress-strain characteristics in
2024-07-08
compression —
Voting terminates on:
2024-09-30
Part 1:
Low-density materials
Matériaux polymères alvéolaires souples — Détermination
de la caractéristique de contrainte-déformation relative en
compression —
Partie 1: Matériaux à basse masse volumique
ICS: ISO ics
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 3386-1:2024(en)
DRAFT
ISO/DIS 3386-1:2024(en)
International
Standard
ISO/DIS 3386-1
ISO/TC 45/SC 4
Polymeric materials, cellular
Secretariat: DSM
flexible — Determination of
Voting begins on:
stress-strain characteristics in
compression —
Voting terminates on:
Part 1:
Low-density materials
Matériaux polymères alvéolaires souples — Détermination
de la caractéristique de contrainte-déformation relative en
compression —
Partie 1: Matériaux à basse masse volumique
ICS: ISO ics
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 3386-1:2024(en)
ii
ISO/DIS 3386-1:2024(en)
Contents Page
Foreword .iv
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Apparatus .2
4.1 Test machine .2
4.2 Supporting surface . .2
4.3 Compression plate .2
5 Test piece .2
5.1 Form and dimensions .2
5.2 Samples showing orientation .2
5.3 Number of test pieces .3
5.4 Conditioning.3
6 Procedure .3
7 Expression of results .4
7.1 Compression stress/strain characteristic .4
7.2 Compression stress value .4
8 Repeat tests . 5
9 Test report . 5
iii
ISO/DIS 3386-1:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO [had/had not] received notice of
(a) patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given f
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.