EN 930:1997/prA2
(Amendment)Footwear, leather and imitation leather goods manufacturing machines - Roughing, scouring, polishing and trimming machines - Safety requirements
Footwear, leather and imitation leather goods manufacturing machines - Roughing, scouring, polishing and trimming machines - Safety requirements
Type 1 amendment.
Maschinen zur Herstellung von Schuhen, Leder- und Kunstlederwaren - Aufrauh-, Ausglas-, Polier- und Kantenbearbeitungsmaschinen - Sicherheitsanforderungen
Machines de fabrication de chaussures et d'articles en cuir et en matériaux similaires - Machines à carder, à verrer, à polir et à fraiser - Prescriptions de sécurité
Stroji za izdelavo obutve ter izdelkov iz usnja in njegovih imitacij - Stroji za grobo obdelavo, brušenje, loščenje in robljenje - Varnostne zahteve
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 930:2000/kprA2:2009
01-april-2009
6WURML]DL]GHODYRREXWYHWHUL]GHONRYL]XVQMDLQQMHJRYLKLPLWDFLM6WURML]DJURER
REGHODYREUXãHQMHORãþHQMHLQUREOMHQMH9DUQRVWQH]DKWHYH
Footwear, leather and imitation leather goods manufacturing machines - Roughing,
scouring, polishing and trimming machines - Safety requirements
Maschinen zur Herstellung von Schuhen, Leder- und Kunstlederwaren - Aufrauh-,
Ausglas-, Polier- und Kantenbearbeitungsmaschinen - Sicherheitsanforderungen
Machines de fabrication de chaussures et d'articles en cuir et en matériaux similaires -
Machines à carder, à verrer, à polir et à fraiser - Prescriptions de sécurité
Ta slovenski standard je istoveten z: EN 930:1997/prA2
ICS:
59.140.40 Stroji in oprema za Machines and equipment for
proizvodnjo usnja in krzna leather and fur production
61.060 Obuvala Footwear
SIST EN 930:2000/kprA2:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 930:2000/kprA2:2009
---------------------- Page: 2 ----------------------
SIST EN 930:2000/kprA2:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 930:1997
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
January 2009
ICS 59.140.40; 61.060
English Version
Footwear, leather and imitation leather goods manufacturing
machines - Roughing, scouring, polishing and trimming
machines - Safety requirements
Machines pour la fabrication de chaussures et d'articles en Maschinen zur Herstellung von Schuhen, Leder- und
cuir et matériaux similaires - Machines à carder, à verrer, à Kunstlederwaren - Aufrauh-, Ausglas-, Polier- und
polir et à fraiser - Prescriptions de sécurité Kantenbearbeitungsmaschinen - Sicherheitsanforderungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 201.
This draft amendment A2, if approved, will modify the European Standard EN 930:1997. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 930:1997/prA2:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 930:2000/kprA2:2009
EN 930:1997/prA2:2009 (E)
Foreword
This document (EN 930:1997/prA2:2009) has been prepared by Technical Committee CEN/TC 201 “Leather
and imitation leather goods and footwear manufacturing machinery - Safety”, the secretariat of which is held
by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
The first reason for amending the published standard EN 930:1997 with A1:2004 is the revision of the EU-
Machinery Directive 98/37/EC into 2006/42/EC, requiring the adaptation of published European Standards
cited in the Official Journal of the European Communities under that Directive.
Additionally at this occasion the normative references have been updated, while also some other limited rather
editorial improvements and corrections have been made.
2
---------------------- Page: 4 ----------------------
SIST EN 930:2000/kprA2:2009
EN 930:1997/prA2:2009 (E)
1 Modification to the Foreword
th
Replace the 4 paragraph with the following: "For relationship with EU Directive(s), see informative Annexes
ZA and ZB, which are integral parts of this document."
2 Modification to the Introduction
Replace the complete text with the following:
"This document is a type C standard as stated in EN ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations and hazardous events are
covered are indicated in the scope of this document.
When provisions of this type C standard are different from those which are stated in type A or B
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.