EN 1651:2018/prA1
(Amendment)Paragliding equipment - Harnesses - Safety requirements and strength tests
Paragliding equipment - Harnesses - Safety requirements and strength tests
This European Standard is applicable only to harnesses for paragliders. The intermediate attachment system between the harness and the paraglider does not form part of this standard.
This Standard specifies safety requirements and test methods.
Ausrüstung für das Gleitschirmfliegen - Gurtzeuge - Sicherheitstechnische Anforderungen und Prüfung der Festigkeit
No Scope Available.
Équipement pour le parapente - Sellettes pour parapente - Éxigences de sécurité et essais de résistance
No Scope Available.
Oprema za jadralno padalstvo - Pasovi - Varnostne zahteve in trdnostni preskusi
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2019
Oprema za jadralno padalstvo - Pasovi - Varnostne zahteve in trdnostni preskusi
Paragliding equipment - Harnesses - Safety requirements and strength tests
Ausrüstung für das Gleitschirmfliegen - Gurtzeuge - Sicherheitstechnische
Anforderungen und Prüfung der Festigkeit
Équipement pour le parapente - Sellettes pour parapente - Éxigences de sécurité et
essais de résistance
Ta slovenski standard je istoveten z: EN 1651:2018/prA1
ICS:
97.220.40 Oprema za športe na Outdoor and water sports
prostem in vodne športe equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
EN 1651:2018
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
April 2019
ICS 97.220.40
English Version
Paragliding equipment - Harnesses - Safety requirements
and strength tests
Équipement pour le parapente - Sellettes pour Ausrüstung für das Gleitschirmfliegen - Gurtzeuge -
parapente - Éxigences de sécurité et essais de Sicherheitstechnische Anforderungen und Prüfung der
résistance Festigkeit
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 136.
This draft amendment A1, if approved, will modify the European Standard EN 1651:2018. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1651:2018/prA1:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Modification to 4.2 “Strength requirements” . 4
2 Modification to 5.5.1 “Strength test methods” . 4
3 Modification to Annex A . 4
European foreword
This document (EN 1651:2018/prA1:2019) has been prepared by Technical Committee CEN/TC 136
“Sports, playground and other recreational facilities and equipment”, the secretariat of which is held by
DIN.
This document is currently submitted to the CEN Enquiry.
In comparison with the previous edition EN 1651:2018, th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.