EN ISO 8469:2021
(Main)Small craft - Non-fire-resistant fuel hoses (ISO 8469:2021)
Small craft - Non-fire-resistant fuel hoses (ISO 8469:2021)
This document specifies general requirements and physical tests for non-fire-resistant hoses for conveying petrol or petrol blended with ethanol, and diesel fuel or diesel fuel blended with FAME, designed for a working pressure not exceeding 0,34 MPa for hoses with inner diameter up to and including 10 mm, and 0,25 MPa for hoses up to 63 mm inner diameter in small craft. .
It applies to hoses for small craft with permanently installed fuel systems.
Specifications for fire-resistant hoses are given in ISO 7840:2021. Specifications for permanently installed fuel systems are given in ISO 10088:2013.
Kleine Wasserfahrzeuge - Nicht feuerwiderstandsfähige Kraftstoffschläuche (ISO 8469:2021)
Dieses Dokument legt allgemeine Anforderungen und physikalische Prüfungen für nicht feuerwiderstandsfähige Schläuche in kleinen Wasserfahrzeugen fest, in denen Benzin oder ein Benzin Ethanol Gemisch oder Diesel oder ein Diesel FAME Gemisch geleitet wird, wobei Schläuche mit Innendurchmesser bis einschließlich 10 mm für Betriebsdrücke bis höchstens 0,34 MPa ausgelegt sind und Schläuche mit Innendurchmesser bis 63 mm für Betriebsdrücke bis 0,25 MPa ausgelegt sind.
Es gilt für Schläuche auf kleinen Wasserfahrzeugen mit fest eingebauten Kraftstoffsystemen.
Festlegungen für feuerwiderstandsfähige Schläuche sind in ISO 7840:2021 gegeben. Festlegungen für fest eingebaute Kraftstoffsysteme sind in ISO 10088:2013 enthalten.
Petits navires - Tuyaux souples pour carburant non résistants au feu (ISO 8469:2021)
Le présent document spécifie les exigences générales et les essais physiques relatifs aux tuyaux souples non résistants au feu pour le transport d'essence ou d'essence mélangée avec de l'éthanol et de carburant diesel ou de carburant diesel mélangé avec des FAME/EMAG, conçus pour une pression de service n'excédant pas 0,34 MPa pour les tuyaux souples de diamètre intérieur égal ou inférieur à 10 mm, et 0,25 MPa pour les tuyaux souples de diamètre intérieur égal ou inférieur à 63 mm, installés sur les petits navires.
Il s'applique aux tuyaux souples destinés aux petits navires dont le système à carburant est installé à demeure.
Les spécifications pour les tuyaux résistant au feu sont données dans l'ISO 7840:2021. Les spécifications pour les systèmes de carburant installés à demeure sont données dans l'ISO 10088:2013.
Mala plovila - Gorljive cevi za gorivo (ISO 8469:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2021
Nadomešča:
SIST EN ISO 8469:2018
Mala plovila - Gorljive cevi za gorivo (ISO 8469:2021)
Small craft - Non-fire-resistant fuel hoses (ISO 8469:2021)
Kleine Wasserfahrzeuge - Nicht feuerwiderstandsfähige Kraftstoffschläuche (ISO
8469:2021)
Petits navires - Tuyaux souples pour carburant non résistants au feu (ISO 8469:2021)
Ta slovenski standard je istoveten z: EN ISO 8469:2021
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
47.020.30 Sistemi cevi Piping systems
47.080 Čolni Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 8469
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2021
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 8469:2018
English Version
Small craft - Non-fire-resistant fuel hoses (ISO 8469:2021)
Petits navires - Tuyaux souples pour carburant non Kleine Wasserfahrzeuge - Nicht
résistants au feu (ISO 8469:2021) feuerwiderstandsfähige Kraftstoffschläuche (ISO
8469:2021)
This European Standard was approved by CEN on 5 January 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8469:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 4
European foreword
This document (EN ISO 8469:2021) has been prepared by Technical Committee ISO/TC 188 "Small
craft" in collaboration with Technical Committee CEN/TC 464 “Small Craft” the secretariat of which is
held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2021, and conflicting national standards
shall be withdrawn at the latest by September 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8469:2018.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 8469:2021 has been approved by CEN as EN ISO 8469:2021 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered
This European standard has been prepared under a Commission’s standardization request M/542
C(2015) 8736 final to provide one voluntary means of conforming to essential requirements of
Directive 2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and
Annex I and II of Directive 2013/53/EU
Essential Requirements of Clause(s)/sub-clause(s) Remarks/Notes
Directive 2013/53/EU of this EN
Annex I, Part A. 5.1 Fuel System, 4, 6 Annex A Fuel hose of the type
General manufactured to this standard
may be used where the filling,
venting and fuel-supply
arrangements do not require fuel
hose to be fire resistant.
Annex II – Components of 4 ,6 Annex A In respect of non-fire-resistant
watercraft (4) – Fuel tanks fuel hoses that are supplied as
intended for fixed installations components only.
and fuel hoses.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 8469
Fourth edition
2021-02
Small craft — Non-fire-resistant fuel
hoses
Petits navires — Tuyaux souples pour carburant non résistants au feu
Reference number
ISO 8469:2021(E)
©
ISO 2021
ISO 8469:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
ISO 8469:2021(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
5 Hose inner diameter . 2
6 Physical tests on finished hose . 3
6.1 General . 3
6.2 Test liquids. 3
6.3 Bursting pressure . 3
6.4 Vacuum collapse test . 3
6.5 Volume change in test liquids. 3
6.6 Mass reduction of test hose. 4
6.7 Effect of ozone . 4
6.8 Fuel permeation . 4
6.9 Cold flex test . 4
6.10 Abrasion test . 4
6.11 Dry heat resistance test . 5
6.12 Oil resistance test . 5
6.13 Adhesion test . 5
7 Marking . 5
Annex A (normative) Fuel permeation test . 6
Bibliography . 8
ISO 8469:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.