EN 61300-2-5:2011

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-5: Tests - Torsion

IEC 61300-2-5:2009(E) Establishes a test to determine the ability of the cable attachment element of the device under test to withstand torsional loads, as might be experienced during installation and normal service, while under tension. The scope of the test also includes those elements designed for ribbon cables. Specific technical changes from the previous edition are as follows: - the title was changed; - the procedure was reconsidered; - the figure of the closure set-up was added; - the severity of the test was reconsidered according to the component.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-5: Prüfungen - Torsion

Dispositifs d'interconnexion et composants passifs à fibres optiques - Procédures fondamentales d'essais et de mesures - Partie 2-5: Essais - Torsion

IEC 61300-2-5:2009 est de déterminer l’aptitude de l’élément de la fixation du câble au dispositif en essai à résister aux efforts de torsion sous tension qui pourraient se produire pendant l’installation et dans des conditions normales de fonctionnement. Le domaine d’application de l’essai comprend également les éléments conçus pour les câbles à rubans. Cette troisième édition annule et remplace la deuxième édition publiée en 2002, dont elle constitue une révision technique. Les modifications techniques par rapport à l’édition précédente sont les suivantes: - le titre a été modifié; - la procédure a été revue; - la figure du montage d’essai d’une terminaison a été ajoutée; - la sévérité de l’essai a été revue en fonction du composant. La présente version bilingue (2020-08) correspond à la version anglaise monolingue publiée en 2009-01.

Optični spojni elementi in pasivne komponente - Postopki osnovnega preskušanja in merjenja - 2-5. del: Preskusi - Torzija/obrat (IEC 61300-2-5:2009)

Namen tega dela IEC 61300 je določiti sposobnost sestavnega dela za pritrditev kabla preskušane naprave, da prenese torzijsko obremenitev pod pritiskom, do katere lahko pride med namestitvijo in običajnim delovanjem. Obseg preskusa zajema tudi sestavne dele, ki so zasnovani za trakaste kable.

General Information

• Status: Withdrawn
• Publication Date: 12-May-2011
• Withdrawal Date: 17-Mar-2012
• ICS: 33.180.20 - Fibre optic interconnecting devices
• Technical Committee: CLC/TC 86BXA - Fibre optic interconnect, passive and connectorised components
• Drafting Committee: IEC/SC 86B - IEC_SC_86B
• Parallel Committee: IEC/SC 86B - IEC_SC_86B
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 19-Oct-2023
• Completion Date: 19-Oct-2023
• Ref Project: SIST EN 61300-2-5:2011 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-5: Tests - Torsion/Twist (IEC 61300-2-5:2009)

Relations

• Replaces: EN 61300-2-5:2002 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-5: Tests - Torsion/twist
• Effective Date: 28-Jan-2023
• Replaced By: EN IEC 61300-2-5:2022 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-5: Tests - Torsion
• Effective Date: 23-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2011
1DGRPHãþD
SIST EN 61300-2-5:2004
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH3RVWRSNLRVQRYQHJDSUHVNXãDQMD
LQPHUMHQMDGHO3UHVNXVL7RU]LMDREUDW,(&
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-5: Tests - Torsion/Twist (IEC 61300-2-5:2009)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-5: Prüfungen - Torsion (IEC 61300-2-5:2009)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Procédures
fondamentales d'essais et de mesures -- Partie 2-5: Essais - Torsion/rotation (CEI 61300
-2-5:2009)
Ta slovenski standard je istoveten z: EN 61300-2-5:2011
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61300-2-5
NORME EUROPÉENNE
May 2011
EUROPÄISCHE NORM
ICS 33.180.20 Supersedes EN 61300-2-5:2002

English version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures -
Part 2-5: Tests -
Torsion
(IEC 61300-2-5:2009)
Dispositifs d'interconnexion et composants Lichtwellenleiter -
passifs à fibres optiques - Verbindungselemente und passive
Procédures fondamentales d'essais et de Bauteile -
mesures - Grundlegende Prüf- und Messverfahren -
Partie 2-5: Essais - Teil 2-5: Prüfungen -
Torsion Torsion
(CEI 61300-2-5:2009) (IEC 61300-2-5:2009)

This European Standard was approved by CENELEC on 2011-03-18. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61300-2-5:2011 E
Foreword
The text of document 86B/2774/FDIS, future edition 3 of IEC 61300-2-5, prepared by SC 86B, Fibre optic
interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the IEC-
CENELEC parallel vote and was approved by CENELEC as EN 61300-2-5 on 2011-03-18.
This European Standard supersedes EN 61300-2-5:2002.
Specific technical changes from EN 61300-2-5:2002 are as follows:
– the title was changed;
– the procedure was reconsidered;
– the figure of closure test set-up was added;
– the severity of the test was reconsidered according to the component.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2011-12-18
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2012-03-18
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61300-2-5:2009 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 61300-2-5:2011
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 61300-1 - Fibre optic interconnecting devices and EN 61300-1 -
passive components - Basic test and
measurement procedures -
Part 1: General and guidance
IEC 61300-3-1 - Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures -
Part 3-1: Examinations and measurements -
Visual examination
IEC 61300-3-3 - Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures -
Part 3-3: Examinations and measurements -
Active monitoring of changes in attenuation
and return loss
IEC 61300-3-4 - Fibre optic interconnecting devices and EN 61300-3-4 -
passive components - Basic test and
measurement procedures -
Part 3-4: Examinations and measurements -
Attenuation
IEC 61300-3-6 - Fibre optic interconnecting devices and EN 61300-3-6 -
passive components - Basic test and
measurement procedures -
Part 3-6: Examinations and measurements -
Return loss
IEC 61300-2-5
Edition 3.0 2009-01
INTERNATIONAL
STANDARD
Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures –
Part 2-5: Tests – Torsion
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
J
ICS 33.180.20 ISBN 978-2-88910-489-5
– 2 – 61300-2-5 © IEC:2009(E)
CONTENTS
FOREWORD.3
1 Scope.5
2 Normative references .5
3 General description .5
4 Apparatus.5
4.1 General .5
4.2 Mounting fixture .6
4.3 Cable clamp .6
4.4 Weights.6
4.5 Optical source and detector.7
5 Procedure .7
5.1 Preparation of specimens .7
5.2 Pre-conditioning .7
5.3 Mount the device under test .7
5.4 Measure the attenuation.7
5.5 Apply cable load.7
5.6 Measure the attenuation.7
5.7 Twist the cable .7
5.8 Test pressure .7
5.9 Monitoring attenuation.8
5.10 Final measurements and examinations.8
6 Severity.8
7 Details to be specified .9

Figure 1 – Component or device test set-up.6
Figure 2 – Closure test set-up.6

Table 1 – Severity levels.8

61300-2-5 © IEC:2009(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-5: Tests – Torsion
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61300-2-5 has been prepared by subcommittee 86B: Fibre optic
interconnecting devices and passive components, of IEC technical committee 86: Fibre optics.
This third edition cancels and replaces the second edition, published in 2002 and constitutes
a technical revision. Specific technical changes from the previous edition are as follows:
– the title was changed;
– the procedure was reconsidered;
– the figure of closure test set-up was added;
– the severity of the test was reconsidered according to the component.

– 4 – 61300-2-5 © IEC:2009(E)
The text of this standard is based on the following documents:
FDIS Report on voting
86B/2774/FDIS 86B/2806/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of IEC 61300 series, published under the general title Fibre optic
interconnecting devices and passive components – Basic test and measurement procedu
...