EN 60115-9-1:2004

Fixed resistors for use in electronic equipment - Part 9-1: Blank detail specification - Fixed surface mount resistor networks with individually measurable resistors - Assessment level EZ

is a supplementary document to the sectional specification and contains requirements for style, layout and minimum content of detail specifications

Festwiderstände zur Verwendung in Geräten der Elektronik - Teil 9-1: Vordruck für Bauartspezifikationen - Oberflächenmontierbare Netzwerke aus Festwiderständen mit einzeln messbaren Widerständen - Bewertungsstufe EZ

Résistances fixes utilisées dans les équipements électroniques - Partie 9-1: Spécification particulière cadre - Réseaux de résistances fixes montés en surface avec des résistances mesurables individuellement - Niveau d'assurance EZ

is a supplementary document to the sectional specification and contains requirements for style, layout and minimum content of detail specifications

Fixed resistors for use in electronic equipment - Part 9-1: Blank detail specification: Fixed surface mount resistor networks with individually measurable resistors - Assessment level EZ (IEC 60115-9-1:2003)

General Information

• Status: Published
• Publication Date: 05-Feb-2004
• ICS: 31.040.10 - Fixed resistors
• Technical Committee: CLC/TC 40XB - CLC/TC 40XB
• Drafting Committee: IEC/TC 40 - IEC_TC_40
• Parallel Committee: IEC/TC 40 - IEC_TC_40
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Start Date: 20-Sep-2017
• Completion Date: 23-Sep-2025
• Ref Project: SIST EN 60115-9-1:2004 - Fixed resistors for use in electronic equipment -- Part 9-1: Blank detail specification - Fixed surface mount resistor networks with individually measurable resistors - Assessment level EZ

Overview

EN 60115-9-1:2004 (IEC 60115-9-1:2003) is a blank detail specification for fixed surface-mount resistor networks with individually measurable resistors, published by CLC/CENELEC. It is a supplementary template to the sectional specification (IEC 60115-9) and the generic specification (IEC 60115-1). The document sets out required style, layout and minimum content for detail specifications and defines the information and test structure to demonstrate conformity at assessment level EZ.

Key topics and requirements

• Purpose and scope: provides the format and mandatory topics that a manufacturer or standards body must include when creating a detail specification for this resistor family.
• Identification fields: prescriptive entries for numbering, title, outline drawing, typical construction, application/assessment level and reference properties.
• Dimensions, ratings and characteristics: template tables for styles, rated dissipation, limiting voltage, insulation voltages, dimensions and resistance ranges; includes requirement to state derating conditions (derating curve).
• Marking and ordering information: required marking rules (per IEC 60115-1 and IEC 60115-9) and minimum ordering fields (resistance, tolerance, spec reference, packaging).
• Inspection and test schedules:
  • Lot-by-lot (Group A / B) and periodic (Group C) test schedules are provided, detailing sampling plans, periodicity, severities and acceptance criteria.
  • Tests referenced include visual examination, dimensional gauging, resistance measurement, solderability, mounting/adhesion, voltage proof/insulation, overload, solvent resistance, shear, substrate bending, climatic sequence and endurance at 70 °C.
  • Sampling and acceptance are aligned with referenced IEC sampling plans (IEC 60410).
• Documentation and records: guidance on certified records of released lots and additional information or increased severities where required.
• Normative references: explicitly references IEC 60115-1 (generic) and IEC 60115-9 (sectional).

Applications and who uses it

• Resistor manufacturers - to prepare compliant detail specifications for fixed SMD resistor networks.
• Quality and test laboratories - to apply the prescribed inspection and sampling plans for product qualification and routine quality conformance.
• Component engineers and purchasers - to understand required markings, performance claims and ordering data.
• Contract manufacturers and OEMs - to ensure component interchangeability, reliability and compliance for electronic equipment designs.
• Regulatory/standards bodies - to harmonize national adoption (CENELEC adoption as EN 60115-9-1:2004).

Related standards

• IEC 60115-1 - Fixed resistors: Generic specification
• IEC 60115-9 - Sectional specification: Fixed surface-mount resistor networks with individually measurable resistors
• EN 60115-9-1:2004 - European adoption by CENELEC

Keywords: EN 60115-9-1, IEC 60115-9-1, fixed resistors, surface mount resistor networks, assessment level EZ, blank detail specification, resistor network testing, quality conformance, marking, derating.

Standards Content (Sample)

SLOVENSKI SIST EN 60115-9-1:2004

STANDARD
september 2004
Fixed resistors for use in electronic equipment - Part 9-1: Blank detail specification:
Fixed surface mount resistor networks with individually measurable resistors -
Assessment level EZ (IEC 60115-9-1:2003)
ICS 31.040.10 Referenčna številka
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

EUROPEAN STANDARD EN 60115-9-1
NORME EUROPÉENNE
EUROPÄISCHE NORM February 2004

ICS 31.040.10
English version
Fixed resistors for use in electronic equipment
Part 9-1: Blank detail specification -
Fixed surface mount resistor networks
with individually measurable resistors -
Assessment level EZ
(IEC 60115-9-1:2003)
Résistances fixes utilisées  Festwiderstände zur Verwendung
dans les équipements électroniques in Geräten der Elektronik
Partie 9-1: Spécification particulière cadre - Teil 9-1: Vordruck für
Réseaux de résistances fixes montés Bauartspezifikationen -
en surface avec des résistances Oberflächenmontierbare Netzwerke
mesurables individuellement - aus Festwiderständen mit einzeln
Niveau d'assurance EZ messbaren Widerständen -
(CEI 60115-9-1:2003) Bewertungsstufe EZ
(IEC 60115-9-1:2003)
This European Standard was approved by CENELEC on 2004-02-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60115-9-1:2004 E
Foreword
The text of document 40/1345/FDIS, future edition 1 of IEC 60115-9-1, prepared by IEC TC 40,
Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote
and was approved by CENELEC as EN 60115-9-1 on 2004-02-01.

The following dates were fixed:

– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-11-01

– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2007-02-01

Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60115-9-1:2003 was approved by CENELEC as a
European Standard without any modification.
__________
- 3 - EN 60115-9-1:2004
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60115-1 1999 Fixed resistors for use in electronic EN 60115-1 2001
(mod) equipment
Part 1: Generic specification
IEC 60115-9 2003 Part 9: Sectional specification - Fixed EN 60115-9 2004
surface mount resistor networks with
individually measurable resistors

INTERNATIONAL IEC
STANDARD 60115-9-1
First edition
2003-10
Fixed resistors for use in electronic equipment –
Part 9-1:
Blank detail specification:
Fixed surface mount resistor networks
with individually measurable resistors –
Assessment level EZ
© IEC 2003 ⎯ Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail]  Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale L
International Electrotechnical Commission
ɆɟɠɞɭɧɚɪɨɞɧɚɹɗɥɟɤɬɪɨɬɟɯɧɢɱɟɫɤɚɹɄɨɦɢɫɫɢɹ
For price, see current catalogue

– 2 – 60115-9-1 © IEC:2003(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT –
Part 9-1: Blank detail specification:
Fixed surface mount resistor networks
with individually measurable resistors –
Assessment level EZ
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60115-9-1 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.
The text of this standard is based on the following documents:
FDIS Report on voting
40/1345/FDIS 40/1367/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

60115-9-1 © IEC:2003(E) – 3 –
The committee has decided that the contents of this publication will remain unchanged until
2008. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual edition of this standard may be issued at a later date.

– 4 – 60115-9-1 © IEC:2003(E)
INTRODUCTION
Blank detail specification
A blank detail specification is a supplementary document to the sectional specification and
contains requirements for style, layout and minimum content of detail specifications. Detail
specifications not complying with these requirements may not be considered as being in
accordance with IEC specifications nor shall they be so described.
In the preparation of detail specifications the content of 1.4 of the sectional specification shall
be taken into account.
The numbers between square brackets on the first page of the detail specification correspond
to the following information which shall be inserted in the position indicated.
Identification of the detail specification
[1] The "International Electrotechnical Commission" o
...