FprEN IEC 61326-2-5:2020

Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditions and performance criteria for field devices with field bus interfaces according to IEC 61784-1

IEC 61326-2-5:2020 is available as IEC 61326-2-5:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61326-2-5:2020 treats the particular features for EMC testing of field devices with field bus interfaces. This part of IEC 61326 covers only the field bus interface of the equipment. This part refers only to field devices intended for use in process control and process measuring. In this document, field devices with interfaces according to IEC 61784-1:2019, CP 3/2 and CP 1/1 as defined in IEC 61784 are covered. Other field bus interfaces may be included in future editions of this document.

Elektrische Mess-, Steuer-, Regel- und Laborgeräte – EMV-Anforderungen – Teil 2-5: Besondere Anforderungen – Prüfanordnungen, Betriebsbedingungen und Leistungsmerkmale für Feldgeräte mit Feldbus-Schnittstellen gemäß IEC 61784-1

Matériel électrique de mesure, de commande et de laboratoire - Exigences relatives à la CEM - Partie 2-5: Exigences particulières - Configurations d'essai, conditions de fonctionnement et critères de performance pour les équipements de terrain avec des interfaces utilisant des bus de terrain conformes à l'IEC 61784-1

IEC 61326-2-5:2020 est disponible sous forme de IEC 61326-2-5:2020 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.L'IEC 61326-1:2020 traite des caractéristiques particulières pour les essais de CEM des équipements de terrain avec des interfaces utilisant des bus de terrain. La présente partie de l’IEC 61326 couvre uniquement l'interface utilisant le bus de terrain du matériel.La présente partie fait uniquement référence aux équipements de terrain destinés à être utilisés pour les commandes et les mesurages des processus. Le présent document traite des équipements de terrain utilisant des interfaces conformes à l’IEC 61784-1:2019, CP 3/2 et CP 1/1 telles qu'elles sont définies dans l’IEC 61784. D'autres interfaces de bus de terrain peuvent être incluses dans les futures éditions du présent document.

Električna oprema za merjenje, nadzor in laboratorijsko uporabo - Zahteve za elektromagnetno združljivost (EMC) - 2-5. del: Posebne zahteve - Preskusne konfiguracije, obratovalni pogoji in merila učinkovitosti za delovanje operativnih naprav s procesnim vodilom ustrezno z IEC 61784-1

Standards Content (sample)

SLOVENSKI STANDARD
oSIST prEN IEC 61326-2-5:2019
01-oktober-2019
Električna oprema za merjenje, kontrolo in laboratorijsko uporabo - Zahteve za
elektromagnetno združljivost (EMC) - 2-5. del: Posebne zahteve - Preskusne
konfiguracije, obratovalni pogoji in merila za delovanje terenskih naprav z
vmesnikom po IEC 61784-1

Electrical equipment for measurement, control and laboratory use - EMC requirements -

Part 2-5: Particular requirements - Test configurations, operational conditions and

performance criteria for field devices with field bus interfaces according to IEC 61784-1

Matériel électrique de mesure, de commande et de laboratoire - Exigences relatives à la

CEM - Partie 2-5: Exigences particulières - Configurations d'essai, conditions de

fonctionnement et critères d'aptitude à la fonction pour les équipements de terrain avec

les interfaces utilisant des bus de terrain conformes à la CEI 61784-1
Ta slovenski standard je istoveten z: prEN IEC 61326-2-5:2019
ICS:
19.080 Električno in elektronsko Electrical and electronic
preskušanje testing
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
oSIST prEN IEC 61326-2-5:2019 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN IEC 61326-2-5:2019
---------------------- Page: 2 ----------------------
oSIST prEN IEC 61326-2-5:2019
65A/927/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 61326-2-5 ED3
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2019-08-23 2019-11-15
SUPERSEDES DOCUMENTS:
65A/908/CD, 65A/918A/CC
IEC SC 65A: SYSTEM ASPECTS
SECRETARIAT: SECRETARY:
United Kingdom Mr Petar Luzajic
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
TC 77, SC 77A
Other TC/SCs are requested to indicate their interest, if any, in
this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY

SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING

Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft for Vote
(CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.

This document is still under study and subject to change. It should not be used for reference purposes.

Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of which they are

aware and to provide supporting documentation.
TITLE:

Electrical equipment for measurement, control and laboratory use – EMC requirements – Part 2-5: Particular

requirements – Test configurations, operational conditions and performance criteria for field devices with field

bus interfaces according to IEC 61784-1
PROPOSED STABILITY DATE: 2023
NOTE FROM TC/SC OFFICERS:

Copyright © 2019 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this

electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.

You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without

permission in writing from IEC.
---------------------- Page: 3 ----------------------
oSIST prEN IEC 61326-2-5:2019
65A/927/CDV – 2 – IEC CDV 61326-2-5 © IEC 2019
1 CONTENTS

2 FOREWORD ........................................................................................................................... 3

3 1 Scope ............................................................................................................................... 5

4 2 Normative references ....................................................................................................... 5

5 3 Terms and definitions ....................................................................................................... 6

6 4 General ............................................................................................................................ 6

7 5 EMC test plan ................................................................................................................... 6

8 5.1 General ................................................................................................................... 6

9 5.2 Configuration of EUT during testing ......................................................................... 6

10 5.3 Operation conditions of EUT during testing .............................................................. 6

11 5.4 Specification of functional performance ................................................................... 6

12 5.5 Test description ....................................................................................................... 6

13 6 Immunity requirements ..................................................................................................... 6

14 6.1 Conditions during the tests ...................................................................................... 6

15 6.2 Immunity test requirements ..................................................................................... 6

16 6.3 Random aspects...................................................................................................... 6

17 6.4 Performance criteria ................................................................................................ 7

18 7 Emission requirements ..................................................................................................... 7

19 8 Test results and test report ............................................................................................... 7

20 9 Instructions for use ........................................................................................................... 7

21 Annex AA (normative) Particular requirements – Test configurations, operational

22 conditions and performance criteria for field devices with field bus interfaces according

23 to IEC 61784-1 CP 1/1 ............................................................................................................ 8

24 Annex BB (normative) Particular requirements – Test configurations, operational

25 conditions and performance criteria for field devices with field bus interfaces according

26 to IEC 61784-1 CP 3/2 .......................................................................................................... 13

28 Figure AA.1 – Test set up for EUT with CP 1/1 interface ....................................................... 10

29 Figure BB.1 – Test set up for EUT with CP 3/2 interface ....................................................... 15

---------------------- Page: 4 ----------------------
oSIST prEN IEC 61326-2-5:2019
IEC CDV 61326-2-5 © IEC 2019 – 3 – 65A/927/CDV
31 INTERNATIONAL ELECTROTECHNICAL COMMISSION
32 ____________
34 ELECTRICAL EQUIPMENT FOR MEASUREMENT,
35 CONTROL AND LABORATORY USE –
36 EMC REQUIREMENTS –
38 Part 2-5: Particular requirements –
39 Test configurations, operational conditions and performance criteria
40 for field devices with field bus interfaces according to IEC 61784-1
43 FOREWORD

44 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

45 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

46 international co-operation on all questions concerning standardization in the electrical and electronic fields. To

47 this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

48 Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

49 Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

50 in the subject dealt with may participate in this preparatory work. International, governmental and non-

51 governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

52 with the International Organization for Standardization (ISO) in accordance with conditions determined by

53 agreement between the two organizations.

54 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

55 consensus of opinion on the relevant subjects since each technical committee has representation from all

56 interested IEC National Committees.

57 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

58 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

59 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

60 misinterpretation by any end user.

61 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

62 transparently to the maximum extent possible in their national and regional publications. Any divergence

63 between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

64 the latter.

65 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

66 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

67 services carried out by independent certification bodies.

68 6) All users should ensure that they have the latest edition of this publication.

69 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

70 members of its technical committees and IEC National Committees for any personal injury, property damage or

71 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

72 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

73 Publications.

74 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

75 indispensable for the correct application of this publication.

76 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of

77 patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

78 International Standard IEC 61326-2-5 has been prepared by subcommittee 65A: System

79 aspects, of IEC technical committee 65: Industrial-process measurement, control and

80 automation.

81 This third edition cancels and replaces the second edition published in 2012. This edition

82 constitutes a technical revision.
---------------------- Page: 5 ----------------------
oSIST prEN IEC 61326-2-5:2019
65A/927/CDV – 4 – IEC CDV 61326-2-5 © IEC 2019

84 The main technical changes with regard to the previous edition are as follows:

85 – Update with respect to IEC 61326-1:20xx.
86 The text of this standard is based on the following documents:
FDIS Report on voting
65A/xxx/FDIS 65A/xxx/RVD

88 Full information on the voting for the approval of this standard can be found in the report on

89 voting indicated in the above table.

90 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

91 This part of IEC 61326 series is to be used in conjunction with IEC 61326-1:20xx and follows

92 the same numbering of clauses, subclauses, tables and figures.

93 When a particular subclause of IEC 61326-1 is not mentioned in this part, that subclause

94 applies as far as is reasonable. When this standard states “addition”, “modification” or

95 “replacement”, the relevant text in IEC 61326-1 is to be adapted accordingly.
96 NOTE The following numbering system is used:

97 – subclauses, tables and figures that are numbered starting from 101 are additional to those in

98 IEC 61326-1;

99 – unless notes are in a new subclause or involve notes in IEC 61326-1, they are numbered starting from 101

100 including those in a replaced clause or subclause;
101 – additional annexes are lettered AA, BB, etc.

102 A list of all parts of IEC 61326 series, under the general title Electrical equipment for

103 measurement, control and laboratory use – EMC requirements can be found on the IEC

104 website.

105 The committee has decided that the contents of this publication will remain unchanged until

106 the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data

107 related to the specific publication. At this date, the publication will be
108 • reconfirmed,
109 • withdrawn,
110 • replaced by a revised edition, or
111 • amended.
112
113
114
---------------------- Page: 6 ----------------------
oSIST prEN IEC 61326-2-5:2019
IEC CDV 61326-2-5 © IEC 2019 – 5 – 65A/927/CDV
115 ELECTRICAL EQUIPMENT FOR MEASUREMENT,
116 CONTROL AND LABORATORY USE –
117 EMC REQUIREMENTS –
118
119 Part 2-5: Particular requirements –
120 Test configurations, operational conditions and performance criteria
121 for field devices with field bus interfaces according to IEC 61784-1
122
123
124
125 1 Scope

126 In addition to the requirements of International Standard IEC 61326-1:20xx, this part of IEC

127 61326 series treats the particular features for EMC testing of field devices with field bus

128 interfaces. This part of IEC 61326 covers only the field bus interface of the equipment.

129 NOTE The other functions of the equipment remain covered by other parts of IEC 61326 series.

130 This part refers only to field devices intended for use in process control and process

131 measuring.

132 In this standard field devices with interfaces according to IEC 61784-1:2014, CP 3/2 and CP

133 1/1 as defined in IEC 61784 are covered. Other field busses may be included in future editions

134 of this standard.

135 The IEC 61784-1:2014 specifies a set of protocol specific communication profiles based on

136 IEC 61158.

137 The manufacturer specifies the environment for which the product is intended to be used

138 and/or selects the appropriate test level specifications of IEC 61326-1.
139 2 Normative references

140 The following documents, in whole or in part, are normatively referenced in this document and

141 are indispensable for its application. For dated references, only the edition cited applies. For

142 undated references, the latest edition of the referenced document (including any

143 amendments) applies.
144 Clause 2 of IEC 61326-1:20xx applies except as follows:
145 Addition:

146 IEC 61158-2:2014, Industrial communication networks – Fieldbus specifications – Part 2:

147 Physical layer specification and service definition

148 IEC 61158-3-3:2014, Industrial communication networks – Fieldbus specifications – Part 3-3:

149 Data-link layer service definition – Type 3 elements

150 IEC 61158-5-5:2014, Industrial communication networks – Fieldbus specifications – Part 5-5:

151 Application layer service definition – Type 5 elements

152 IEC 61158-6-10:2014, Industrial communication networks – Fieldbus specifications – Part 6-

153 10: Application layer protocol specification – Type 10 elements
---------------------- Page: 7 ----------------------
oSIST prEN IEC 61326-2-5:2019
65A/927/CDV – 6 – IEC CDV 61326-2-5 © IEC 2019

154 IEC 61784-1:2014, Industrial communication networks – Profiles – Part 1: Fieldbus profiles

155 3 Terms and definitions
156 Clause 3 of IEC 61326-1:20xx applies.
157 4 General
158 Clause 4 of IEC 61326-1:20xx applies.
159 5 EMC test plan
160 5.1 General
161 Subclause 5.1 of IEC 61326-1:20xx applies.
162 5.2 Configuration of EUT during testing
163 Subclause 5.2 of IEC 61326-1:20xx applies, except as follows:
164 Addition:
165 Additional requirements: see Annexes AA and BB.
166 5.3 Operation conditions of EUT during testing
167 Subclause 5.3 of IEC 61326-1:20xx applies, except as follows:
168 Addition:
169 Additional requirements: see Annexes AA and BB.
170 5.4 Specification of functional performance
171 Subclause 5.4 of IEC 61326-1:20xx applies.
172 5.5 Test description
173 Subclause 5.5 of IEC 61326-1:20xx applies.
174 6 Immunity requirements
175 6.1 Conditions during the tests
176 Subclause 6.1 of IEC 61326-1:20xx applies.
177 6.2 Immunity test requirements
178 Subclause 6.2 of IEC 61326-1:20xx applies.
179 6.3 Random aspects
180 Subclause 6.3 of IEC 61326-1:20xx applies.
---------------------- Page: 8 ----------------------
oSIST prEN IEC 61326-2-5:2019
IEC CDV 61326-2-5 © IEC 2019 – 7 – 65A/927/CDV
181 6.4 Performance criteria
182 Subclause 6.4 of IEC 61326-1:20xx applies, except as follows:
183 Addition:
184 Additional requirements: see Annexes AA and BB.
185 7 Emission requirements
186 Clause 7 of IEC 61326-1:20xx applies.
187 8 Test results and test report
188 Clause 8 of IEC 61326-1:20xx applies, except as follows:
189 Addition:
190 The type of shield connection at the EUT shall be stated in the test report.
191 9 Instructions for use
192 Clause 9 of IEC 61326-1:20xx applies.
193
---------------------- Page: 9 ----------------------
oSIST prEN IEC 61326-2-5:2019
65A/927/CDV – 8 – IEC CDV 61326-2-5 © IEC 2019
194 Annex AA
195 (normative)
196
197 Particular requirements –
198 Test configurations, operational conditions and performance criteria for
199 field devices with field bus interfaces according to IEC 61784-1 CP 1/1
200
201 AA.1 General

202 In connection with the main part of this standard, this Annex AA describes specific test

203 configurations, operational conditions and performance criteria regarding the field bus

204 interface using the communication profile CP 1/1 according to IEC 61784-1:2014.

205 To prevent confusion with requirements of other annexes, the equipment under test (EUT) is

206 called “EUT with CP 1/1 interface” throughout this annex.
207 AA.2 EMC test plan
208 AA.2.1 Configuration of EUT with CP 1/1 interface during testing
209 Subclause 5.2 of IEC 61326-1:20xx applies, except as follows:
210 Addition:
211 AA.2.1.1 Test configuration for EUT with CP 1/1 interface

212 In order to assign any malfunction of the communication during the EMC-test to the EUT with

213 CP 1/1 interface, the configuration of field devices with interfaces according to IEC 61784-

214 1:2014, CP 1/1 shall be limited to the operation of one host system and one EUT with CP 1/1

215 interface during EMC type tests.

216 Ports other than I/O ports covered by this part of the standard are tested according to

217 IEC 61326-1:20xx.
218 The connection plan is shown in Figure AA.1.

219 The field device is connected via a device coupler with the power conditioner and the host

220 system.
221 A standardised field bus terminator is attached
...