EN 61158-6-19:2012

Industrial communication networks - Fieldbus specifications - Part 6-19: Application layer protocol specification - Type 19 elements

IEC 61158-6-19:2010(E) specifies the protocol of the Type 19 fieldbus application layer, in conformance with the OSI Basic Reference Model (ISO/IEC 7498-1) and the OSI application layer structure (ISO/IEC 9545). It defines the protocol provided to define the wire-representation of the service primitives defined in IEC 61158-5-19:2010, and the externally visible behavior associated with their transfer. This second edition cancels and replaces the first edition published in 2007 and constitutes a technical revision. The main changes with respect to the previous edition are: - increasing the number of supported devices (511 instead of 254); - introducing a communication version identification; - adding a mechanism for remote address allocation; - introducing enhanced parameter addressing (32 bit instead of 16 bit); - restructuring control and status word; - improving the redundancy and hotplug features; - improving the error handling; adding a multiplexing protocol (SMP: Type 19 Messaging Protocol).

Industrielle Kommunikationsnetze - Feldbusse - Teil 6-19: Protokollspezifikation des Application Layer (Anwendungsschicht) - Typ 19-Elemente

Réseaux de communication industriels - Spécifications des bus de terrain - Partie 6-19: Spécification des protocoles des couches d'application - Eléments de type 19

Industrijska komunikacijska omrežja - Specifikacije za procesno vodilo - 6-19. del: Specifikacija protokola na aplikacijskem nivoju - Elementi tipa 19 (IEC 61158-6-19:2010 )

Aplikacijski nivo procesnih vodil (FAL) omogoča uporabniškim programom dostop do komunikacijskega okolja procesnih vodil. Glede na to je mogoče aplikacijski nivo procesnih vodil šteti za »okno med ustreznimi aplikacijami«. Ta standard določa skupne elemente za osnovne časovno kritične in časovno nekritične sporočilne komunikacije med aplikacijami v avtomatizacijskem okolju in material, specifičen za procesna vodila tipa 19. Izraz »časovno kritičen« se uporablja za predstavitev prisotnosti časovnega okna, v okviru katerega se zahteva dokončanje enega ali več opredeljenih dejanj z določeno stopnjo gotovosti. Zaradi neuspešnega dokončanja opredeljenih dejanj v časovnem oknu je možna odpoved aplikacij, ki zahtevajo dejanja, pri čemer so ogroženi oprema, obrat in morda človeška življenja. Ta standard na abstrakten način določa zunanje vidno opravilo, ki ga zagotavljajo različni tipi aplikacijskih nivojev procesnih vodil v zvezi z a) abstraktnim modelom za določanje aplikacijskih virov (objektov), ki jih uporabniki lahko spreminjajo prek opravila aplikacijskega nivoja procesnih vodil, b) primitivnimi dejanji in dogodki opravila; c) parametri, povezanimi z vsakim primitivnim dejanjem in dogodkom, in obliko, ki jo prevzamejo; ter d) medsebojno povezavo med temi dejanji in dogodki ter njihovimi veljavnimi zaporedji. Namen tega standarda je opredeliti opravila, ki se zagotavljajo za a) uporabnika aplikacijskega nivoja procesnih vodil na meji med uporabnikom in aplikacijskim nivojem referenčnega modela procesnih vodil ter b) v upravljanje sistemov na meji med aplikacijskim nivojem in upravljanje sistemov referenčnega modela procesnih vodil. Ta standard določa strukturo in opravila aplikacijskega nivoja procesnih vodil IEC v skladu z osnovnim referenčnim modelom OSI (ISO/IEC 7498) in strukturo aplikacijskega nivoja OSI (ISO/IEC 9545). Opravila in protokole aplikacijskega nivoja procesnih vodil zagotavljajo aplikacijski osebki (AE) aplikacijskega nivoja procesnih vodil znotraj aplikacijskih procesov. Aplikacijski osebek aplikacijskega nivoja procesnih vodil sestavljata sklop objektno usmerjenih aplikacijskih opravilnih elementov (ASE) in osebek za upravljanje nivojev (LME), ki upravlja aplikacijski osebek. Aplikacijski opravilni elementi zagotavljajo komunikacijska opravila, ki delujejo na sklopu povezanih razredov objektov aplikacijskega procesa (APO). Med aplikacijske opravilne elemente aplikacijskega nivoja procesnih vodil spada aplikacijski opravilni element za upravljanje, ki zagotavlja skupen sklop opravil za upravljanje primerkov razredov aplikacijskega nivoja procesnih vodil. Čeprav ta opravila določajo način izdajanja in dostavljanja zahtev in odzivov z vidika aplikacij, ne zajemajo specifikacije v zvezi s tem, kako naj se nanje odzovejo aplikacije, ki te zahteve in odzive oddajajo. To pomeni, da vedenjski vidiki aplikacij niso opredeljeni; opredeljena je le definicija zahtev in odzivov, ki jih lahko pošiljajo/prejemajo. Tako se uporabnikom aplikacijskega nivoja procesnih vodil omogoči večja prilagodljivost pri standardizaciji takega vedenja objektov. Poleg teh opravil so v tem standardu opredeljena tudi nekatera podporna opravila, da se omogoči dostop do aplikacijskega nivoja procesnih vodil za nadzorovanje nekaterih vidikov njegovega delovanja.

General Information

• Status: Withdrawn
• Publication Date: 21-Jun-2012
• Withdrawal Date: 27-Mar-2015
• ICS: 25.040.40 - Industrial process measurement and control
• ICS: 35.100.70 - Application layer
• ICS: 35.110 - Networking
• Technical Committee: CLC/TC 65X - Industrial-process measurement, control and automation
• Drafting Committee: IEC/SC 65C - IEC_SC_65C
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 23-Sep-2017
• Completion Date: 23-Sep-2017
• Mandate: M/490 - Standardisation mandate to the European Standardisation Organisations (ESOs) to support European Smart Grid deployment
• Ref Project: SIST EN 61158-6-19:2012 - Industrial communication networks - Fieldbus specifications - Part 6-19: Application layer protocol specification - Type 19 elements (IEC 61158-6-19:2010 )

Relations

• Replaces: EN 61158-6-19:2008 - Industrial communication networks - Fieldbus specifications - Part 6-19: Application layer protocol specification - Type 19 elements
• Effective Date: 29-Jan-2023
• Replaced By: EN 61158-6-19:2014 - Industrial communication networks - Fieldbus specifications - Part 6-19: Application layer protocol specification - Type 19 elements
• Effective Date: 04-Nov-2014

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2012
1DGRPHãþD
SIST EN 61158-6-19:2008
Industrijska komunikacijska omrežja - Specifikacije za procesno vodilo - 6-19. del:
Specifikacija protokola na aplikacijskem nivoju - Elementi tipa 19 (IEC 61158-6-
19:2010 )
Industrial communication networks - Fieldbus specifications - Part 6-19: Application layer
protocol specification - Type 19 elements (IEC 61158-6-19:2010 )
Industrielle Kommunikationsnetze - Feldbusse - Teil 6-19: Protokollspezifikation des
Application Layer (Anwendungsschicht) - Typ 19-Elemente (IEC 61158-6-19:2010 )
Réseaux de communication industriels - Spécifications des bus de terrain - Partie 6-19:
Spécification des protocoles des couches d'application - Eléments de type 19 (CEI
61158-6-19:2010 )
Ta slovenski standard je istoveten z: EN 61158-6-19:2012
ICS:
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
35.100.70 Uporabniški sloj Application layer
35.110 Omreževanje Networking
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61158-6-19
NORME EUROPÉENNE
June 2012
EUROPÄISCHE NORM
ICS 25.040.40; 35.100.70; 35.110 Supersedes EN 61158-6-19:2008

English version
Industrial communication networks -
Fieldbus specifications -
Part 6-19: Application layer protocol specification -
Type 19 elements
(IEC 61158-6-19:2010)
Réseaux de communication industriels -  Industrielle Kommunikationsnetze -
Spécifications des bus de terrain - Feldbusse -
Partie 6-19: Spécification des protocoles Teil 6-19: Protokollspezifikation des
des couches d'application - Application Layer (Anwendungsschicht) -
Eléments de type 19 Typ 19-Elemente
(CEI 61158-6-19:2010) (IEC 61158-6-19:2010)

This European Standard was approved by CENELEC on 2012-03-28. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61158-6-19:2012 E
Foreword
The text of document 65C/607/FDIS, future edition 2 of IEC 61158-6-19, prepared by SC 65C, "Industrial
networks", of IEC/TC 65, "Industrial-process measurement, control and automation" was submitted to the
IEC-CENELEC parallel vote and approved by CENELEC as EN 61158-6-19:2012.

The following dates are fixed:
(dop) 2012-12-28
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2015-03-28

standards conflicting with the
document have to be withdrawn
This document supersedes EN 61158-6-19:2008.
19:2008:
— increasing the number of supported devices (511 instead of 254);
— introducing a communication version identification;
— adding a mechanism for remote address allocation;
— introducing enhanced parameter addressing (32 bit instead of 16 bit);
— restructuring control and status word;
— improving the redundancy and hotplug features;
— improving the error handling;
— adding a multiplexing protocol (SMP: Type 19 Messaging Protocol).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 61158-6-19:2010 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 61131 series NOTE  Harmonized in EN 61131 series.
IEC/TR 61158-1:2010 NOTE  Harmonized as CLC/TR 61158-1:2010 (not modified).
IEC 61158-4-16:2007 NOTE  Harmonized as EN 61158-4-16:2008 (not modified).
IEC 61784-1:2010 NOTE  Harmonized as EN 61784-1:2010 (not modified).
IEC 61784-2:2010 NOTE  Harmonized as EN 61784-2:2010 (not modified).

- 3 - EN 61158-6-19:2012
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 61158-3-19 - Industrial communication networks - Fieldbus EN 61158-3-19 -
specifications -
Part 3-19: Data-link layer service definition -
Type 19 elements
IEC 61158-4-19 - Industrial communication networks - Fieldbus EN 61158-4-19 -
specifications -
Part 4-19: Data-link layer protocol
specification - Type 19 elements

IEC 61158-5-19 - Industrial communication networks - Fieldbus EN 61158-5-19 -
specifications -
Part 5-19: Application layer service definition -
Type 19 elements
ISO/IEC 7498-1 - Information technology - Open Systems - -
Interconnection - Basic Reference Model:
The Basic Model
ISO/IEC 8822 - Information technology - Open Systems - -
Interconnection - Presentation service
definition
ISO/IEC 8824 - Information technology - Open Systems - -
Interconnection - Specification of Abstract
Syntax Notation One (ASN.1)
ISO/IEC 10731 - Information technology - Open Systems - -
Interconnection - Basic reference model -
Conventions for the definition of OSI services

IEC 61158-6-19 ®
Edition 2.0 2010-08
INTERNATIONAL
STANDARD
Industrial communication networks – Fieldbus specifications –
Part 6-19: Application layer protocol specification – Type 19 elements

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
T
ICS 25.04.40; 35.100.70; 35.110 ISBN 978-2-88912-133-5
– 2 – 61158-6-19 © IEC:2010(E)
CONTENTS
FOREWORD.4
INTRODUCTION.6
1 Scope.7
1.1 General .7
1.2 Specifications.8
1.3 Conformance.8
2 Normative references .8
3 Terms, definitions, abbreviations, symbols and conventions .9
3.1 Referenced terms and definitions .9
3.2 Additional terms and definitions.10
3.3 Additional abbreviations and symbols.11
3.4 Conventions .11
4 Abstract syntax.12
5 Transfer syntax .12
5.1 Introduction .12
5.2 RTC PDU merged abstract and transfer syntax .12
6 Structure of FAL protocol state machines .12
7 AP-context state machine.14
7.1 Overview .14
7.2 States .14
7.3 States, events and transitions .14
8 FAL service protocol machine (FSPM).15
8.1 Overview .15
8.2 MGT services .15
8.3 IDN services.16
8.4 CYCIDN services .16
9 Application relationship protocol machine (ARPM).16
9.1 Overview .16
9.2 Master ARPM .17
9.3 Slave ARPM.18
9.4 Primitives received from the FSPM.19
9.5 Indications received from the DMPM .20
10 DLL mapping protocol machine (DMPM).21
10.1 Overview .21
10.2 Primitives received from the ARPM .21
10.3 Indications received from the DL .22
Bibliography.23

Figure 1 – Relationships among protocol machines and adjacent layers .13
Figure 2 – APCSM state diagram .14
Figure 3 – ARPM master AR state diagram .17
Figure 4 – ARPM slave AR state diagram .18

Table 1 – RTC PDU attribute format .12

61158-6-19 © IEC:2010(E) – 3 –
Table 2 – APCSM state-event table .15
Table 3 – Master ARPM state-event table .18
Table 4 – Slave ARPM state-event table .19
Table 5 – ARPM to DL mapping .22
Table 6 – DL to ARPM mapping .22

– 4 – 61158-6-19 © IEC:2010(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
INDUSTRIAL COMMUNICATION NETWORKS –
FIELDBUS SPECIFICATIONS –
Part 6-19: Application layer protocol specification –
Type 19 elements
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical commi
...