ETSI EN 302 217-1 V3.2.2 (2020-02)
Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 1: Overview, common characteristics and system-independent requirements
Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 1: Overview, common characteristics and system-independent requirements
REN/ATTM-0441
Fiksni radijski sistemi - Karakteristike in zahteve za opremo tipa točka-točka in antene - 1. del: Pregled, splošne karakteristike in sistemsko neodvisne zahteve
General Information
Buy Standard
Standards Content (Sample)
ETSI EN 302 217-1 V3.2.2 (2020-02)
EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 1: Overview, common characteristics and
system-independent requirements
---------------------- Page: 1 ----------------------
2 ETSI EN 302 217-1 V3.2.2 (2020-02)
Reference
REN/ATTM-0441
Keywords
antenna, DFRS, DRRS, FWA, point-to-point,
radio, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 302 217-1 V3.2.2 (2020-02)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 11
3 Definition of terms, symbols and abbreviations . 13
3.1 Terms . 13
3.2 Symbols . 18
3.3 Abbreviations . 19
4 Structure and applicability of the ETSI EN 302 217 series . 21
4.1 Generality . 21
4.2 Cross references to previously relevant ENs and TSs . 22
4.3 Summary of system options provided . 23
4.4 User's guide . 26
5 General characteristics . 28
5.1 Frequency bands and channel arrangements . 28
5.2 Special compatibility requirements between systems . 28
5.3 Transmission capacity and spectral efficiency . 28
5.4 Performance and availability requirements . 28
5.5 Environmental profiles . 29
5.5.0 Introduction. 29
5.5.1 Environmental profile declared under Directive 2014/53/EU . 29
5.5.2 ETSI environmental profiles . 29
5.5.2.0 Generality . 29
5.5.2.1 Equipment intended for telecommunications applications installed in weather-protected locations
(indoor locations) . 30
5.5.2.2 Equipment intended for telecommunications applications installed in not-weather-protected
locations (outdoor locations) . 30
5.5.3 Test environment profiles . 30
5.6 Power supply . 30
5.6.0 Introduction. 30
5.6.1 Power supply profile declared under Directive 2014/53/EU . 30
5.6.2 ETSI power supply profile . 31
5.7 System block diagram . 31
6 Baseband interfaces and parameters . 31
6.0 Introduction . 31
6.1 Ethernet interfaces . 32
6.2 Plesiochronous interfaces . 32
6.3 Synchronous digital hierarchy interfaces . 32
6.4 Other baseband data interfaces . 32
7 Main requirements . 32
7.0 Introduction . 32
7.1 General requirements . 33
7.1.1 System identification . 33
7.1.2 System nominal loading . 33
7.1.3 Environmental profile . 33
7.2 Transmitter characteristics. 33
7.2.1 Transmitter power and power tolerance . 33
7.2.1.1 Maximum power and EIRP . 33
7.2.1.2 Combined TX power and EIRP limits . 34
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 302 217-1 V3.2.2 (2020-02)
7.2.1.3 Output power tolerance . 34
7.2.2 Transmitter power and frequency control . 34
7.2.2.1 Transmitter power control (ATPC and RTPC) . 34
7.2.2.1.1 Automatic Transmitter Power Control (ATPC) . 34
7.2.2.1.2 Remote Transmitter Power Control (RTPC) . 35
7.2.2.2 Remote Frequency Control (RFC) . 35
7.2.3 Radio Frequency (RF) spectrum mask. 35
7.2.4 Discrete CW components exceeding the spectrum mask limit . 35
7.2.4.1 Discrete CW components at the symbol rate . 35
7.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 35
7.2.5 Unwanted emissions in the spurious domain - external . 36
7.2.6 Dynamic change of modulation order . 36
7.2.7 Radio frequency tolerance . 36
7.2.8 Emission limitations outside the allocated band . 36
7.3 Receiver characteristics . 36
7.3.1 Unwanted emissions in the spurious domain - external . 36
7.3.2 BER as a function of receiver signal level . 36
7.3.3 Receiver selectivity . 36
7.3.3.1 Introduction . 36
7.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 36
7.3.3.3 CW spurious interference (blocking and spurious response) . 37
7.4 Antenna directional characteristics . 37
8 Complementary requirements . 37
8.0 Introduction . 37
8.1 Branching/feeder requirements . 37
8.1.1 Waveguide flanges (or other connectors) . 37
8.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 38
8.2 Intermodulation products . 39
8.3 Transmitter characteristics. 39
8.3.1 Unwanted emissions - internal . 39
8.3.2 Radio Frequency (RF) spectrum mask when mixed manufacturer compatibility is required . 40
8.4 Receiver characteristics . 40
8.4.1 Maximum input level and input level range . 40
8.4.2 Unwanted emissions - internal . 41
8.4.3 Image rejection . 41
8.4.4 Innermost channel selectivity . 42
8.5 System performance without diversity . 42
8.5.1 Equipment Residual BER (RBER) . 42
8.5.2 Distortion sensitivity . 44
8.5.2.1 Introduction . 44
8.5.2.2 Requirement . 44
8.5.2.3 Assessment . 45
8.5.3 Interference sensitivity for CCDP with XPIC operation . 46
8.5.3.1 General . 46
8.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 46
8.6 System characteristics with diversity . 46
8.6.0 Introduction. 46
8.6.1 Differential delay compensation . 46
8.6.2 BER performance . 46
Annex A (normative): Spectrum masks and receiver selectivity when mixed manufacturer
compatibility is required . 47
A.0 Introduction . 47
A.1 TX masks assessment . 48
A.2 Normal channels - Emission mask floor . 48
A.2.1 RBER impact . 48
A.2.2 Local TX to RX compatibility . 48
A.2.2.1 Spectrum mask . 48
A.2.2.2 Receiver selectivity . 49
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 302 217-1 V3.2.2 (2020-02)
A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel
separation of 28 MHz to 30 MHz . 49
A.3.0 Introduction . 49
A.3.1 Innermost channels spectrum masks . 49
A.3.2 Receiver innermost channel selectivity . 51
A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel
separation of 40 MHz . 52
A.4.0 Introduction . 52
A.4.1 Innermost channels spectrum masks . 52
A.4.2 Receiver innermost channels selectivity . 53
A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 54
A.5.0 Introduction . 54
A.5.1 Innermost channels spectrum masks . 54
A.5.2 Receiver innermost channels selectivity . 55
Annex B (normative): Definition of equivalent data rates for packet data, PDH/SDH and
other signals on the traffic interface. 57
Annex C (informative): Information on Multi-channel and Channel-aggregation differences
and operation . 58
Annex D (informative): Additional information on relevant characteristics and operation . 60
D.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 60
D.2 Measurement test set for XPI characteristics . 61
D.3 Differential delay compensation range . 62
D.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 63
D.4.1 FER/BER equivalence . 63
D.4.2 FER equipment settings and measurement techniques (example) . 64
D.5 Impact of power control (ATPC and/or RTPC), mixed-mode and bandwidth adaptive operation
on spectrum mask and link design requirements . 64
D.5.0 Introduction . 64
D.5.1 ATPC and RTPC . 64
D.5.1.1 ATPC . 64
D.5.1.2 ATPC and RTPC implementation background . 65
D.5.2 Mixed−mode and bandwidth adaptive operation impact . 67
D.5.2.1 Mixed−mode basic concepts . 67
D.5.2.2 Bandwidth adaptive . 68
D.5.2.2.1 Basic concepts . 68
D.5.2.2.2 Bandwidth (channel) occupancy . 68
D.5.3 Impact on frequency co ordination . 68
D.5.4 Impact of operating conditions on the access to radio spectrum through European Harmonised Standard . 68
D.6 Typical interference sensitivity behaviour for frequency planning purpose . 69
Annex E (informative): Mechanical characteristics . 70
Annex F (informative): Mitigation techniques referred in CEPT/ERC/DEC(00)07
(18 GHz band) . 71
Annex G (informative): Change history . 72
History . 73
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 302 217-1 V3.2.2 (2020-02)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and
Multiplexing (ATTM).
The present document is part 1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas, as identified below (see note):
Part 1: "Overview, common characteristics and system-independent requirements";
Part 2: "Digital systems operating in frequency bands from 1 GHz to 86 GHz; Harmonised Standard for access to
radio spectrum";
Part 4: "Antennas".
NOTE: In previous regulatory regime under Directive 1999/5/EC more parts (harmonised and non-harmonised
standards) were published. Since Directive 2014/53/EU [i.1] repealed Directive 1999/5/EC the following
parts have been replaced while the content has been moved to other parts of the series.
Those parts are:
Part 2-1: Technical content moved to present document (Part 1);
Part 2-2: Technical content reproduced in Part 2 (*);
(*) Part 2-2- was also published in the OJEU under Directive 2014/53/EU [i.1], presumption of
conformity ceased on 31-12-2018;
Part 3: Technical content moved to Part 2 (including a complete new set of receiver parameters);
Part 4-1: Technical content reproduced in Part 4;
Part 4-2: Technical content reproduced in Part 4.
National transposition dates
Date of adoption of this EN: 4 February 2020
Date of latest announcement of this EN (doa): 31 May 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2020
Date of withdrawal of any conflicting National Standard (dow): 30 November 2020
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 302 217-1 V3.2.2 (2020-02)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 302 217-1 V3.2.2 (2020-02)
1 Scope
The present document applies to Digital Fixed Radio Systems (DFRS) in point-to-point operation with integral and
external antennas in the frequency range of 1 GHz to 86 GHz corresponding to the appropriate frequency bands
1,4 GHz to 86 GHz as described in ETSI EN 302 217-2 [18], annex B to annex J.
The present document summarizes:
• all characteristics, principles and, of utmost importance, terms and definitions that are common to all
P-P equipment and ante
...
SLOVENSKI STANDARD
SIST EN 302 217-1 V3.2.2:2020
01-april-2020
Fiksni radijski sistemi - Karakteristike in zahteve za opremo tipa točka-točka in
antene - 1. del: Pregled, splošne karakteristike in sistemsko neodvisne zahteve
Fixed Radio Systems - Characteristics and requirements for point-to-point equipment
and antennas - Part 1: Overview, common characteristics and system-independent
requirements
Ta slovenski standard je istoveten z: ETSI EN 302 217-1 V3.2.2 (2020-02)
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
33.120.40 Antene Aerials
SIST EN 302 217-1 V3.2.2:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 302 217-1 V3.2.2:2020
---------------------- Page: 2 ----------------------
SIST EN 302 217-1 V3.2.2:2020
ETSI EN 302 217-1 V3.2.2 (2020-02)
EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 1: Overview, common characteristics and
system-independent requirements
---------------------- Page: 3 ----------------------
SIST EN 302 217-1 V3.2.2:2020
2 ETSI EN 302 217-1 V3.2.2 (2020-02)
Reference
REN/ATTM-0441
Keywords
antenna, DFRS, DRRS, FWA, point-to-point,
radio, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 302 217-1 V3.2.2:2020
3 ETSI EN 302 217-1 V3.2.2 (2020-02)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 11
3 Definition of terms, symbols and abbreviations . 13
3.1 Terms . 13
3.2 Symbols . 18
3.3 Abbreviations . 19
4 Structure and applicability of the ETSI EN 302 217 series . 21
4.1 Generality . 21
4.2 Cross references to previously relevant ENs and TSs . 22
4.3 Summary of system options provided . 23
4.4 User's guide . 26
5 General characteristics . 28
5.1 Frequency bands and channel arrangements . 28
5.2 Special compatibility requirements between systems . 28
5.3 Transmission capacity and spectral efficiency . 28
5.4 Performance and availability requirements . 28
5.5 Environmental profiles . 29
5.5.0 Introduction. 29
5.5.1 Environmental profile declared under Directive 2014/53/EU . 29
5.5.2 ETSI environmental profiles . 29
5.5.2.0 Generality . 29
5.5.2.1 Equipment intended for telecommunications applications installed in weather-protected locations
(indoor locations) . 30
5.5.2.2 Equipment intended for telecommunications applications installed in not-weather-protected
locations (outdoor locations) . 30
5.5.3 Test environment profiles . 30
5.6 Power supply . 30
5.6.0 Introduction. 30
5.6.1 Power supply profile declared under Directive 2014/53/EU . 30
5.6.2 ETSI power supply profile . 31
5.7 System block diagram . 31
6 Baseband interfaces and parameters . 31
6.0 Introduction . 31
6.1 Ethernet interfaces . 32
6.2 Plesiochronous interfaces . 32
6.3 Synchronous digital hierarchy interfaces . 32
6.4 Other baseband data interfaces . 32
7 Main requirements . 32
7.0 Introduction . 32
7.1 General requirements . 33
7.1.1 System identification . 33
7.1.2 System nominal loading . 33
7.1.3 Environmental profile . 33
7.2 Transmitter characteristics. 33
7.2.1 Transmitter power and power tolerance . 33
7.2.1.1 Maximum power and EIRP . 33
7.2.1.2 Combined TX power and EIRP limits . 34
ETSI
---------------------- Page: 5 ----------------------
SIST EN 302 217-1 V3.2.2:2020
4 ETSI EN 302 217-1 V3.2.2 (2020-02)
7.2.1.3 Output power tolerance . 34
7.2.2 Transmitter power and frequency control . 34
7.2.2.1 Transmitter power control (ATPC and RTPC) . 34
7.2.2.1.1 Automatic Transmitter Power Control (ATPC) . 34
7.2.2.1.2 Remote Transmitter Power Control (RTPC) . 35
7.2.2.2 Remote Frequency Control (RFC) . 35
7.2.3 Radio Frequency (RF) spectrum mask. 35
7.2.4 Discrete CW components exceeding the spectrum mask limit . 35
7.2.4.1 Discrete CW components at the symbol rate . 35
7.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 35
7.2.5 Unwanted emissions in the spurious domain - external . 36
7.2.6 Dynamic change of modulation order . 36
7.2.7 Radio frequency tolerance . 36
7.2.8 Emission limitations outside the allocated band . 36
7.3 Receiver characteristics . 36
7.3.1 Unwanted emissions in the spurious domain - external . 36
7.3.2 BER as a function of receiver signal level . 36
7.3.3 Receiver selectivity . 36
7.3.3.1 Introduction . 36
7.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 36
7.3.3.3 CW spurious interference (blocking and spurious response) . 37
7.4 Antenna directional characteristics . 37
8 Complementary requirements . 37
8.0 Introduction . 37
8.1 Branching/feeder requirements . 37
8.1.1 Waveguide flanges (or other connectors) . 37
8.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 38
8.2 Intermodulation products . 39
8.3 Transmitter characteristics. 39
8.3.1 Unwanted emissions - internal . 39
8.3.2 Radio Frequency (RF) spectrum mask when mixed manufacturer compatibility is required . 40
8.4 Receiver characteristics . 40
8.4.1 Maximum input level and input level range . 40
8.4.2 Unwanted emissions - internal . 41
8.4.3 Image rejection . 41
8.4.4 Innermost channel selectivity . 42
8.5 System performance without diversity . 42
8.5.1 Equipment Residual BER (RBER) . 42
8.5.2 Distortion sensitivity . 44
8.5.2.1 Introduction . 44
8.5.2.2 Requirement . 44
8.5.2.3 Assessment . 45
8.5.3 Interference sensitivity for CCDP with XPIC operation . 46
8.5.3.1 General . 46
8.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 46
8.6 System characteristics with diversity . 46
8.6.0 Introduction. 46
8.6.1 Differential delay compensation . 46
8.6.2 BER performance . 46
Annex A (normative): Spectrum masks and receiver selectivity when mixed manufacturer
compatibility is required . 47
A.0 Introduction . 47
A.1 TX masks assessment . 48
A.2 Normal channels - Emission mask floor . 48
A.2.1 RBER impact . 48
A.2.2 Local TX to RX compatibility . 48
A.2.2.1 Spectrum mask . 48
A.2.2.2 Receiver selectivity . 49
ETSI
---------------------- Page: 6 ----------------------
SIST EN 302 217-1 V3.2.2:2020
5 ETSI EN 302 217-1 V3.2.2 (2020-02)
A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel
separation of 28 MHz to 30 MHz . 49
A.3.0 Introduction . 49
A.3.1 Innermost channels spectrum masks . 49
A.3.2 Receiver innermost channel selectivity . 51
A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel
separation of 40 MHz . 52
A.4.0 Introduction . 52
A.4.1 Innermost channels spectrum masks . 52
A.4.2 Receiver innermost channels selectivity . 53
A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 54
A.5.0 Introduction . 54
A.5.1 Innermost channels spectrum masks . 54
A.5.2 Receiver innermost channels selectivity . 55
Annex B (normative): Definition of equivalent data rates for packet data, PDH/SDH and
other signals on the traffic interface. 57
Annex C (informative): Information on Multi-channel and Channel-aggregation differences
and operation . 58
Annex D (informative): Additional information on relevant characteristics and operation . 60
D.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 60
D.2 Measurement test set for XPI characteristics . 61
D.3 Differential delay compensation range . 62
D.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 63
D.4.1 FER/BER equivalence . 63
D.4.2 FER equipment settings and measurement techniques (example) . 64
D.5 Impact of power control (ATPC and/or RTPC), mixed-mode and bandwidth adaptive operation
on spectrum mask and link design requirements . 64
D.5.0 Introduction . 64
D.5.1 ATPC and RTPC . 64
D.5.1.1 ATPC . 64
D.5.1.2 ATPC and RTPC implementation background . 65
D.5.2 Mixed−mode and bandwidth adaptive operation impact . 67
D.5.2.1 Mixed−mode basic concepts . 67
D.5.2.2 Bandwidth adaptive . 68
D.5.2.2.1 Basic concepts . 68
D.5.2.2.2 Bandwidth (channel) occupancy . 68
D.5.3 Impact on frequency co ordination . 68
D.5.4 Impact of operating conditions on the access to radio spectrum through European Harmonised Standard . 68
D.6 Typical interference sensitivity behaviour for frequency planning purpose . 69
Annex E (informative): Mechanical characteristics . 70
Annex F (informative): Mitigation techniques referred in CEPT/ERC/DEC(00)07
(18 GHz band) . 71
Annex G (informative): Change history . 72
History . 73
ETSI
---------------------- Page: 7 ----------------------
SIST EN 302 217-1 V3.2.2:2020
6 ETSI EN 302 217-1 V3.2.2 (2020-02)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and
Multiplexing (ATTM).
The present document is part 1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas, as identified below (see note):
Part 1: "Overview, common characteristics and system-independent requirements";
Part 2: "Digital systems operating in frequency bands from 1 GHz to 86 GHz; Harmonised Standard for access to
radio spectrum";
Part 4: "Antennas".
NOTE: In previous regulatory regime under Directive 1999/5/EC more parts (harmonised and non-harmonised
standards) were published. Since Directive 2014/53/EU [i.1] repealed Directive 1999/5/EC the following
parts have been replaced while the content has been moved to other parts of the series.
Those parts are:
Part 2-1: Technical content moved to present document (Part 1);
Part 2-2: Technical content reproduced in Part 2 (*);
(*) Part 2-2- was also published in the OJEU under Directive 2014/53/EU [i.1], presumption of
conformity ceased on 31-12-2018;
Part 3: Technical content moved to Part 2 (including a complete new set of receiver parameters);
Part 4-1: Technical content reproduced in Part 4;
Part 4-2: Technical content reproduced in Part 4.
National transposition dates
Date of adoption of this EN: 4 February 2020
Date of latest announcement of this EN (doa): 31 May 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2020
Date of withdrawal of any conflic
...
Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 1: Overview, common characteristics and
system-independent requirements
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
Reference
REN/ATTM-0441
Keywords
antenna, DFRS, DRRS, FWA, point-to-point,
radio, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 11
3 Definition of terms, symbols and abbreviations . 13
3.1 Terms . 13
3.2 Symbols . 18
3.3 Abbreviations . 19
4 Structure and applicability of the ETSI EN 302 217 series . 21
4.1 Generality . 21
4.2 Cross references to previously relevant ENs and TSs . 22
4.3 Summary of system options provided . 23
4.4 User's guide . 26
5 General characteristics . 28
5.1 Frequency bands and channel arrangements . 28
5.2 Special compatibility requirements between systems . 28
5.3 Transmission capacity and spectral efficiency . 28
5.4 Performance and availability requirements . 28
5.5 Environmental profiles . 29
5.5.0 Introduction. 29
5.5.1 Environmental profile declared under Directive 2014/53/EU . 29
5.5.2 ETSI environmental profiles . 29
5.5.2.0 Generality . 29
5.5.2.1 Equipment intended for telecommunications applications installed in weather-protected locations
(indoor locations) . 30
5.5.2.2 Equipment intended for telecommunications applications installed in not-weather-protected
locations (outdoor locations) . 30
5.5.3 Test environment profiles . 30
5.6 Power supply . 30
5.6.0 Introduction. 30
5.6.1 Power supply profile declared under Directive 2014/53/EU . 30
5.6.2 ETSI power supply profile . 31
5.7 System block diagram . 31
6 Baseband interfaces and parameters . 31
6.0 Introduction . 31
6.1 Ethernet interfaces . 32
6.2 Plesiochronous interfaces . 32
6.3 Synchronous digital hierarchy interfaces . 32
6.4 Other baseband data interfaces . 32
7 Main requirements . 32
7.0 Introduction . 32
7.1 General requirements . 33
7.1.1 System identification . 33
7.1.2 System nominal loading . 33
7.1.3 Environmental profile . 33
7.2 Transmitter characteristics. 33
7.2.1 Transmitter power and power tolerance . 33
7.2.1.1 Maximum power and EIRP . 33
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
7.2.1.2 Combined TX power and EIRP limits . 34
7.2.1.3 Output power tolerance . 34
7.2.2 Transmitter power and frequency control . 34
7.2.2.1 Transmitter power control (ATPC and RTPC) . 34
7.2.2.1.1 Automatic Transmitter Power Control (ATPC) . 34
7.2.2.1.2 Remote Transmitter Power Control (RTPC) . 35
7.2.2.2 Remote Frequency Control (RFC) . 35
7.2.3 Radio Frequency (RF) spectrum mask. 35
7.2.4 Discrete CW components exceeding the spectrum mask limit . 35
7.2.4.1 Discrete CW components at the symbol rate . 35
7.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 35
7.2.5 Unwanted emissions in the spurious domain - external . 36
7.2.6 Dynamic change of modulation order . 36
7.2.7 Radio frequency tolerance . 36
7.2.8 Emission limitations outside the allocated band . 36
7.3 Receiver characteristics . 36
7.3.1 Unwanted emissions in the spurious domain - external . 36
7.3.2 BER as a function of receiver signal level . 36
7.3.3 Receiver selectivity . 36
7.3.3.1 Introduction . 36
7.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 36
7.3.3.3 CW spurious interference (blocking and spurious response) . 37
7.4 Antenna directional characteristics . 37
8 Complementary requirements . 37
8.0 Introduction . 37
8.1 Branching/feeder requirements . 37
8.1.1 Waveguide flanges (or other connectors) . 37
8.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 38
8.2 Intermodulation products . 39
8.3 Transmitter characteristics. 39
8.3.1 Unwanted emissions - internal . 39
8.3.2 Radio Frequency (RF) spectrum mask when mixed manufacturer compatibility is required . 39
8.4 Receiver characteristics . 40
8.4.1 Maximum input level and input level range . 40
8.4.2 Unwanted emissions - internal . 41
8.4.3 Image rejection . 41
8.4.4 Innermost channel selectivity . 42
8.5 System performance without diversity . 42
8.5.1 Equipment Residual BER (RBER) . 42
8.5.2 Distortion sensitivity . 44
8.5.2.1 Introduction . 44
8.5.2.2 Requirement . 44
8.5.2.3 Assessment . 45
8.5.3 Interference sensitivity for CCDP with XPIC operation . 46
8.5.3.1 General . 46
8.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 46
8.6 System characteristics with diversity . 46
8.6.0 Introduction. 46
8.6.1 Differential delay compensation . 46
8.6.2 BER performance . 46
Annex A (normative): Spectrum masks and receiver selectivity when mixed manufacturer
compatibility is required . 47
A.0 Introduction . 47
A.1 TX masks assessment . 48
A.2 Normal channels - Emission mask floor . 48
A.2.1 RBER impact . 48
A.2.2 Local TX to RX compatibility . 48
A.2.2.1 Spectrum mask . 48
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
A.2.2.2 Receiver selectivity . 49
A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel
separation of 28 MHz to 30 MHz . 49
A.3.0 Introduction . 49
A.3.1 Innermost channels spectrum masks . 49
A.3.2 Receiver innermost channel selectivity . 51
A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel
separation of 40 MHz . 52
A.4.0 Introduction . 52
A.4.1 Innermost channels spectrum masks . 52
A.4.2 Receiver innermost channels selectivity . 53
A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 54
A.5.0 Introduction . 54
A.5.1 Innermost channels spectrum masks . 54
A.5.2 Receiver innermost channels selectivity . 55
Annex B (normative): Definition of equivalent data rates for packet data, PDH/SDH and
other signals on the traffic interface. 57
Annex C (informative): Information on Multi-channel and Channel-aggregation differences
and operation . 58
Annex D (informative): Additional information on relevant characteristics and operation . 60
D.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 60
D.2 Measurement test set for XPI characteristics . 61
D.3 Differential delay compensation range . 62
D.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 63
D.4.1 FER/BER equivalence . 63
D.4.2 FER equipment settings and measurement techniques (example) . 64
D.5 Impact of power control (ATPC and/or RTPC), mixed-mode and bandwidth adaptive operation
on spectrum mask and link design requirements . 64
D.5.0 Introduction . 64
D.5.1 ATPC and RTPC . 64
D.5.1.1 ATPC . 64
D.5.1.2 ATPC and RTPC implementation background . 65
D.5.2 Mixed−mode and bandwidth adaptive operation impact . 67
D.5.2.1 Mixed−mode basic concepts . 67
D.5.2.2 Bandwidth adaptive . 68
D.5.2.2.1 Basic concepts . 68
D.5.2.2.2 Bandwidth (channel) occupancy . 68
D.5.3 Impact on frequency co ordination . 68
D.5.4 Impact of operating conditions on the access to radio spectrum through European Harmonised Standard . 68
D.6 Typical interference sensitivity behaviour for frequency planning purpose . 69
Annex E (informative): Mechanical characteristics . 70
Annex F (informative): Mitigation techniques referred in CEPT/ERC/DEC(00)07
(18 GHz band) . 71
Annex G (informative): Change history . 72
History . 73
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This final draft European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals,
Transmission and Multiplexing (ATTM), and is now submitted for the Vote phase of the ETSI standards EN Approval
Procedure.
The present document is part 1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas, as identified below (see note):
Part 1: "Overview, common characteristics and system-independent requirements";
Part 2: "Digital systems operating in frequency bands from 1 GHz to 86 GHz; Harmonised Standard for access to
radio spectrum";
Part 4: "Antennas".
NOTE: In previous regulatory regime under Directive 1999/5/EC more parts (harmonised and non-harmonised
standards) were published. Since Directive 2014/53/EU [i.1] repealed Directive 1999/5/EC the following
parts have been replaced while the content has been moved to other parts of the series.
Those parts are:
Part 2-1: Technical content moved to present document (Part 1);
Part 2-2: Technical content reproduced in Part 2 (*);
(*) Part 2-2- was also published in the OJEU under Directive 2014/53/EU [i.1], presumption of
conformity will cease on 31-12-2018;
Part 3: Technical content moved to Part 2 (including a complete new set of receiver parameters);
Part 4-1: Technical content reproduced in Part 4;
Part 4-2: Technical content reproduced in Part 4.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 302 217-1 V3.2.1 (2019-12)
1 Scope
The present document applies to Digital Fixed Radio Systems (DFRS) in point-to-point operation with integral and
external antennas in the frequency range of 1 GHz to 86 GHz corresponding to the appropriate frequency bands
1,4 GHz to 86 GHz as described in ETSI EN 302 217-2 [18]
...
Draft ETSI EN 302 217-1 V3.2.0 (2019-03)
EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 1: Overview, common characteristics and
system-independent requirements
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 217-1 V3.2.0 (2019-03)
Reference
REN/ATTM-0441
Keywords
antenna, DFRS, DRRS, FWA, point-to-point,
radio, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 217-1 V3.2.0 (2019-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 11
3 Definition of terms symbols and abbreviations . 13
3.1 Terms . 13
3.2 Symbols . 18
3.3 Abbreviations . 19
4 Structure and applicability of the ETSI EN 302 217 series . 21
4.1 Generality . 21
4.2 Cross references to previously relevant ENs and TSs . 22
4.3 Summary of system options provided . 23
4.4 User's guide . 26
5 General characteristics . 28
5.1 Frequency bands and channel arrangements . 28
5.2 Special compatibility requirements between systems . 28
5.3 Transmission capacity and spectral efficiency . 28
5.4 Performance and availability requirements . 28
5.5 Environmental profiles . 29
5.5.0 Introduction. 29
5.5.1 Environmental profile declared under Directive 2014/53/EU . 29
5.5.2 ETSI environmental profiles . 29
5.5.2.0 Generality . 29
5.5.2.1 Equipment intended for telecommunications applications installed in weather-protected locations
(indoor locations) . 30
5.5.2.2 Equipment intended for telecommunications applications installed in not-weather-protected
locations (outdoor locations) . 30
5.5.3 Test environment profiles . 30
5.6 Power supply . 30
5.6.0 Introduction. 30
5.6.1 Power supply profile declared under Directive 2014/53/EU . 30
5.6.2 ETSI power supply profile . 31
5.7 System block diagram . 31
6 Baseband interfaces and parameters . 31
6.0 Introduction . 31
6.1 Ethernet interfaces . 32
6.2 Plesiochronous interfaces . 32
6.3 Synchronous digital hierarchy interfaces . 32
6.4 Other baseband data interfaces . 32
7 Main requirements . 32
7.0 Introduction . 32
7.1 General requirements . 33
7.1.1 System identification . 33
7.1.2 System nominal loading . 33
7.1.3 Environmental profile . 33
7.2 Transmitter characteristics. 33
7.2.1 Transmitter power and power tolerance . 33
7.2.1.1 Maximum power and EIRP . 33
7.2.1.2 Combined TX power and EIRP limits . 34
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 217-1 V3.2.0 (2019-03)
7.2.1.3 Output power tolerance . 34
7.2.2 Transmitter power and frequency control . 34
7.2.2.1 Transmitter power control (ATPC and RTPC) . 34
7.2.2.1.1 Automatic Transmitter Power Control (ATPC) . 34
7.2.2.1.2 Remote Transmitter Power Control (RTPC) . 35
7.2.2.2 Remote Frequency Control (RFC) . 35
7.2.3 Radio Frequency (RF) spectrum mask. 35
7.2.4 Discrete CW components exceeding the spectrum mask limit . 35
7.2.4.1 Discrete CW components at the symbol rate . 35
7.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 35
7.2.5 Unwanted emissions in the spurious domain - external . 35
7.2.6 Dynamic change of modulation order . 36
7.2.7 Radio frequency tolerance . 36
7.2.8 Emission limitations outside the allocated band . 36
7.3 Receiver characteristics . 36
7.3.1 Unwanted emissions in the spurious domain - external . 36
7.3.2 BER as a function of receiver signal level . 36
7.3.3 Receiver selectivity . 36
7.3.3.1 Introduction . 36
7.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 36
7.3.3.3 CW spurious interference (blocking and spurious response) . 36
7.4 Antenna directional characteristics . 37
8 Complementary requirements . 37
8.0 Introduction . 37
8.1 Branching/feeder requirements . 37
8.1.1 Waveguide flanges (or other connectors) . 37
8.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 38
8.2 Intermodulation products . 39
8.3 Transmitter characteristics. 39
8.3.1 Unwanted emissions - internal . 39
8.3.2 Radio Frequency (RF) spectrum mask when mixed manufacturer compatibility is required . 39
8.4 Receiver characteristics . 40
8.4.1 Maximum input level and input level range . 40
8.4.2 Unwanted emissions - internal . 41
8.4.3 Image rejection . 41
8.4.4 Innermost channel selectivity . 42
8.5 System performance without diversity . 42
8.5.1 Equipment Residual BER (RBER) . 42
8.5.2 Distortion sensitivity . 44
8.5.2.1 Introduction . 44
8.5.2.2 Requirement . 44
8.5.2.3 Assessment . 45
8.5.3 Interference sensitivity for CCDP with XPIC operation . 46
8.5.3.1 General . 46
8.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 46
8.6 System characteristics with diversity . 46
8.6.0 Introduction. 46
8.6.1 Differential delay compensation . 46
8.6.2 BER performance . 46
Annex A (normative): Spectrum masks and receiver selectivity when mixed manufacturer
compatibility is required . 47
A.0 Introduction . 47
A.1 TX masks assessment . 48
A.2 Normal channels - Emission mask floor . 48
A.2.1 RBER impact . 48
A.2.2 Local TX to RX compatibility . 48
A.2.2.1 Spectrum mask . 48
A.2.2.2 Receiver selectivity . 49
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 217-1 V3.2.0 (2019-03)
A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel
separation of 28 MHz to 30 MHz . 49
A.3.0 Introduction . 49
A.3.1 Innermost channels spectrum masks . 49
A.3.2 Receiver innermost channel selectivity . 51
A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel
separation of 40 MHz . 52
A.4.0 Introduction . 52
A.4.1 Innermost channels spectrum masks . 52
A.4.2 Receiver innermost channels selectivity . 53
A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 54
A.5.0 Introduction . 54
A.5.1 Innermost channels spectrum masks . 54
A.5.2 Receiver innermost channels selectivity . 55
Annex B (normative): Definition of equivalent data rates for packet data, PDH/SDH and
other signals on the traffic interface. 57
Annex C (informative): Information on Multi-channel and Channel-aggregation differences
and operation . 58
Annex D (informative): Additional information on relevant characteristics and operation . 60
D.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 60
D.2 Measurement test set for XPI characteristics . 61
D.3 Differential delay compensation range . 62
D.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 63
D.4.1 FER/BER equivalence . 63
D.4.2 FER equipment settings and measurement techniques (example) . 64
D.5 Impact of power control (ATPC and/or RTPC), mixed-mode and bandwidth adaptive operation
on spectrum mask and link design requirements . 64
D.5.0 Introduction . 64
D.5.1 ATPC and RTPC . 64
D.5.1.1 ATPC . 64
D.5.1.2 ATPC and RTPC implementation background . 65
D.5.2 Mixed−mode and bandwidth adaptive operation impact . 67
D.5.2.1 Mixed−mode basic concepts . 67
D.5.2.2 Bandwidth adaptive . 68
D.5.2.2.1 Basic concepts . 68
D.5.2.2.2 Bandwidth (channel) occupancy . 68
D.5.3 Impact on frequency co ordination . 68
D.5.4 Impact of operating conditions on the access to radio spectrum through European Harmonised Standard . 68
D.6 Typical interference sensitivity behaviour for frequency planning purpose . 69
Annex E (informative): Mechanical characteristics . 70
Annex F (informative): Mitigation techniques referred in ERC/DEC(00)07 (18 GHz band) . 71
Annex G (informative): Change history . 72
History . 73
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 302 217-1 V3.2.0 (2019-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission
and Multiplexing (ATTM), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document is part 1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas, as identified below (see note):
Part 1: "Overview, common characteristics and system-independent requirements";
Part 2: "Digital systems operating in frequency bands from 1 GHz to 86 GHz; Harmonised Standard for access to
radio spectrum.
Part 4: "Antennas".
NOTE: In previous regulatory regime of harmonised and non-harmonised standards under Directive 1999/5/EC
more parts were published, which have been superseded since Directive 2014/53/EU [i.1] repealed
Directive 1999/5/EC;
Those are:
Part 2-1: Technical content moved to present document (Part 1);
Part 2-2: Technical content reproduced in Part 2 (*);
(*) Part 2-2- was also published in the OJEU under Directive 2014/53/EU [i.1], presumption of
conformity will cease on 31-12-2018;
Part 3: Technical content moved to Part 2 (including a complete new set of receiver parameters);
Part 4-1: Technical content reproduced in Part 4;
Part 4-2: Technical content reproduced in Part 4.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 302 217-1 V3.2.0 (2019-03)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 302 217-1 V3.2.0 (2019-03)
1 Scope
The present document applies to Digital Fixed Radio Systems (DFRS) in point-to-point operation with integral and
external antennas in the frequency range of 1 GHz to 86 GHz corresponding to the appropriate frequency bands
1,4 GHz to 86 GHz as described in ETSI EN 302 217-2 [18], annex B to annex J.
The present document summarizes:
• all characteristics, principles and, of utmost importance, terms and definitions that are common to all
P-P equipment and antennas and
...
SLOVENSKI STANDARD
oSIST prEN 302 217-1 V3.2.0:2019
01-maj-2019
)LNVQLUDGLMVNLVLVWHPL.DUDNWHULVWLNHLQ]DKWHYH]DRSUHPRLQDQWHQHWLSDWRþND
WRþNDGHO 3UHJOHGVSORãQHNDUDNWHULVWLNHLQVLVWHPVNRQHRGYLVQH]DKWHYH
Fixed Radio Systems - Characteristics and requirements for point-to-point equipment
and antennas - Part 1: Overview, common characteristics and system-independent
requirements
Ta slovenski standard je istoveten z: ETSI EN 302 217-1 V3.2.0 (2019-03)
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
33.120.40 Antene Aerials
oSIST prEN 302 217-1 V3.2.0:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 302 217-1 V3.2.0:2019
---------------------- Page: 2 ----------------------
oSIST prEN 302 217-1 V3.2.0:2019
Draft ETSI EN 302 217-1 V3.2.0 (2019-03)
EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 1: Overview, common characteristics and
system-independent requirements
---------------------- Page: 3 ----------------------
oSIST prEN 302 217-1 V3.2.0:2019
2 Draft ETSI EN 302 217-1 V3.2.0 (2019-03)
Reference
REN/ATTM-0441
Keywords
antenna, DFRS, DRRS, FWA, point-to-point,
radio, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 302 217-1 V3.2.0:2019
3 Draft ETSI EN 302 217-1 V3.2.0 (2019-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 11
3 Definition of terms symbols and abbreviations . 13
3.1 Terms . 13
3.2 Symbols . 18
3.3 Abbreviations . 19
4 Structure and applicability of the ETSI EN 302 217 series . 21
4.1 Generality . 21
4.2 Cross references to previously relevant ENs and TSs . 22
4.3 Summary of system options provided . 23
4.4 User's guide . 26
5 General characteristics . 28
5.1 Frequency bands and channel arrangements . 28
5.2 Special compatibility requirements between systems . 28
5.3 Transmission capacity and spectral efficiency . 28
5.4 Performance and availability requirements . 28
5.5 Environmental profiles . 29
5.5.0 Introduction. 29
5.5.1 Environmental profile declared under Directive 2014/53/EU . 29
5.5.2 ETSI environmental profiles . 29
5.5.2.0 Generality . 29
5.5.2.1 Equipment intended for telecommunications applications installed in weather-protected locations
(indoor locations) . 30
5.5.2.2 Equipment intended for telecommunications applications installed in not-weather-protected
locations (outdoor locations) . 30
5.5.3 Test environment profiles . 30
5.6 Power supply . 30
5.6.0 Introduction. 30
5.6.1 Power supply profile declared under Directive 2014/53/EU . 30
5.6.2 ETSI power supply profile . 31
5.7 System block diagram . 31
6 Baseband interfaces and parameters . 31
6.0 Introduction . 31
6.1 Ethernet interfaces . 32
6.2 Plesiochronous interfaces . 32
6.3 Synchronous digital hierarchy interfaces . 32
6.4 Other baseband data interfaces . 32
7 Main requirements . 32
7.0 Introduction . 32
7.1 General requirements . 33
7.1.1 System identification . 33
7.1.2 System nominal loading . 33
7.1.3 Environmental profile . 33
7.2 Transmitter characteristics. 33
7.2.1 Transmitter power and power tolerance . 33
7.2.1.1 Maximum power and EIRP . 33
7.2.1.2 Combined TX power and EIRP limits . 34
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 302 217-1 V3.2.0:2019
4 Draft ETSI EN 302 217-1 V3.2.0 (2019-03)
7.2.1.3 Output power tolerance . 34
7.2.2 Transmitter power and frequency control . 34
7.2.2.1 Transmitter power control (ATPC and RTPC) . 34
7.2.2.1.1 Automatic Transmitter Power Control (ATPC) . 34
7.2.2.1.2 Remote Transmitter Power Control (RTPC) . 35
7.2.2.2 Remote Frequency Control (RFC) . 35
7.2.3 Radio Frequency (RF) spectrum mask. 35
7.2.4 Discrete CW components exceeding the spectrum mask limit . 35
7.2.4.1 Discrete CW components at the symbol rate . 35
7.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 35
7.2.5 Unwanted emissions in the spurious domain - external . 35
7.2.6 Dynamic change of modulation order . 36
7.2.7 Radio frequency tolerance . 36
7.2.8 Emission limitations outside the allocated band . 36
7.3 Receiver characteristics . 36
7.3.1 Unwanted emissions in the spurious domain - external . 36
7.3.2 BER as a function of receiver signal level . 36
7.3.3 Receiver selectivity . 36
7.3.3.1 Introduction . 36
7.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 36
7.3.3.3 CW spurious interference (blocking and spurious response) . 36
7.4 Antenna directional characteristics . 37
8 Complementary requirements . 37
8.0 Introduction . 37
8.1 Branching/feeder requirements . 37
8.1.1 Waveguide flanges (or other connectors) . 37
8.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 38
8.2 Intermodulation products . 39
8.3 Transmitter characteristics. 39
8.3.1 Unwanted emissions - internal . 39
8.3.2 Radio Frequency (RF) spectrum mask when mixed manufacturer compatibility is required . 39
8.4 Receiver characteristics . 40
8.4.1 Maximum input level and input level range . 40
8.4.2 Unwanted emissions - internal . 41
8.4.3 Image rejection . 41
8.4.4 Innermost channel selectivity . 42
8.5 System performance without diversity . 42
8.5.1 Equipment Residual BER (RBER) . 42
8.5.2 Distortion sensitivity . 44
8.5.2.1 Introduction . 44
8.5.2.2 Requirement . 44
8.5.2.3 Assessment . 45
8.5.3 Interference sensitivity for CCDP with XPIC operation . 46
8.5.3.1 General . 46
8.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 46
8.6 System characteristics with diversity . 46
8.6.0 Introduction. 46
8.6.1 Differential delay compensation . 46
8.6.2 BER performance . 46
Annex A (normative): Spectrum masks and receiver selectivity when mixed manufacturer
compatibility is required . 47
A.0 Introduction . 47
A.1 TX masks assessment . 48
A.2 Normal channels - Emission mask floor . 48
A.2.1 RBER impact . 48
A.2.2 Local TX to RX compatibility . 48
A.2.2.1 Spectrum mask . 48
A.2.2.2 Receiver selectivity . 49
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 302 217-1 V3.2.0:2019
5 Draft ETSI EN 302 217-1 V3.2.0 (2019-03)
A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel
separation of 28 MHz to 30 MHz . 49
A.3.0 Introduction . 49
A.3.1 Innermost channels spectrum masks . 49
A.3.2 Receiver innermost channel selectivity . 51
A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel
separation of 40 MHz . 52
A.4.0 Introduction . 52
A.4.1 Innermost channels spectrum masks . 52
A.4.2 Receiver innermost channels selectivity . 53
A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 54
A.5.0 Introduction . 54
A.5.1 Innermost channels spectrum masks . 54
A.5.2 Receiver innermost channels selectivity . 55
Annex B (normative): Definition of equivalent data rates for packet data, PDH/SDH and
other signals on the traffic interface. 57
Annex C (informative): Information on Multi-channel and Channel-aggregation differences
and operation . 58
Annex D (informative): Additional information on relevant characteristics and operation . 60
D.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 60
D.2 Measurement test set for XPI characteristics . 61
D.3 Differential delay compensation range . 62
D.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 63
D.4.1 FER/BER equivalence . 63
D.4.2 FER equipment settings and measurement techniques (example) . 64
D.5 Impact of power control (ATPC and/or RTPC), mixed-mode and bandwidth adaptive operation
on spectrum mask and link design requirements . 64
D.5.0 Introduction . 64
D.5.1 ATPC and RTPC . 64
D.5.1.1 ATPC . 64
D.5.1.2 ATPC and RTPC implementation background . 65
D.5.2 Mixed−mode and bandwidth adaptive operation impact . 67
D.5.2.1 Mixed−mode basic concepts . 67
D.5.2.2 Bandwidth adaptive . 68
D.5.2.2.1 Basic concepts . 68
D.5.2.2.2 Bandwidth (channel) occupancy . 68
D.5.3 Impact on frequency co ordination . 68
D.5.4 Impact of operating conditions on the access to radio spectrum through European Harmonised Standard . 68
D.6 Typical interference sensitivity behaviour for frequency planning purpose . 69
Annex E (informative): Mechanical characteristics . 70
Annex F (informative): Mitigation techniques referred in ERC/DEC(00)07 (18 GHz band) . 71
Annex G (informative): Change history . 72
History . 73
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 302 217-1 V3.2.0:2019
6 Draft ETSI EN 302 217-1 V3.2.0 (2019-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission
and Multiplexing (ATTM), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document is part 1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas, as identified below (see note):
Part 1: "Overview, common characteristics and system-independent requirements";
Part 2: "Digital systems operating in frequency bands from 1 GHz to 86 GHz; Harmonised Standard for access to
radio spectrum.
Part 4: "Antennas".
NOTE: In previous regulatory regime of harmonised and non-harmonised standards under Directive 1999/5/EC
more parts were published, which have been superseded since Directive 2014/53/EU [i.1] repealed
Directive 1999/5/EC;
Those are:
Part 2-1: Technical content moved to present document (Part 1);
Part 2-2: Technical content reproduced in Part 2 (*);
(*) Part 2-2- was also published in the OJEU under Directive 2014/53/EU [i.1], presumption of
conformity will cease on 31-12-2018;
Part 3: Technical content moved to Part 2 (including a complete new set of receiver parameters);
Part 4-1: Technical content reproduced in Part 4;
Part 4-2: Technical content reproduced in Part 4.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.