ETSI EN 301 166 V2.1.1 (2016-11)

Land Mobile Service; Radio equipment for analogue and/or digital communication (speech and/or data) and operating on narrow band channels and having an antenna connector; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU

REN/ERM-TGDMR-344

Storitev kopenskih mobilnih komunikacij - Radijska oprema za analogne oziroma digitalne komunikacije (prenos govora oziroma podatkov), ki deluje v ozkopasovnih kanalih in ima antenski konektor - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU

Ta dokument obravnava tehnične zahteve za radijske oddajnike in sprejemnike, ki se uporabljajo v postajah za storitev zasebnega mobilnega radia (PMR). Velja za uporabo storitve kopenskih mobilnih komunikacij, ki deluje na radijskih frekvencah med 30 MHz in 3 GHz z ozkimi medkanalskimi razmiki (CSP) (manj kot 10 kHz) ter je namenjena za govor in/ali podatke. Namen tega dokumenta je obravnava vseh pasovnih širin kanalov (CBW), ki jih za take sisteme dovoljujejo nacionalne uprave, npr. 6,25 kHz. V tem dokumentu so podane različne zahteve za različne radiofrekvenčne pasove, okoljske pogoje in vrste opreme, kjer je ustrezno.
V tem dokumentu so sistemi za prenos podatkov opredeljeni kot sistemi, ki prenašajo in/ali prejemajo podatke in/ali digitaliziran govor. Oprema zajema oddajnik ter ustrezen kodirnik in modulator in/ali sprejemnik ter ustrezen demodulator in odkodirnik.
Ta dokument obravnava opremo, ki lahko uporablja modulacijo s konstantno ali nekonstantno ovojnico.
Ta dokument obravnava naslednje vrste opreme:
– bazna postaja: oprema z antenskim konektorjem;
– mobilna postaja: oprema z antenskim konektorjem.
Prenosne postaje:
a) z antenskim konektorjem ali
b) brez zunanjega antenskega konektorja, vendar s stalnim ali začasnim notranjim 50-ohmskim radiofrekvenčnim konektorjem, ki omogoča dostop do izhoda oddajnika in vhoda sprejemnika.
Ta dokument ne obravnava opreme prenosne postaje brez zunanjega ali notranjega radiofrekvenčnega konektorja in brez možnosti namestitve začasnega notranjega 50-ohmskega radiofrekvenčnega konektorja.
Ta dokument vključuje zahteve, s katerimi se dokazuje, da »... mora biti radijska oprema izdelana tako, da učinkovito uporablja in tudi podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivih motenj« in da
»... radijska oprema podpira določene funkcije, ki zagotavljajo dostop do storitev za nujne primere« [i.3].
Poleg tega dokumenta se lahko za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN (npr. ETSI EN 301 489-1 [i.4] in ETSI EN 301 489-5 [i.5]), ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz Direktive o radijski opremi [i.3].

General Information

• Status: Published
• Publication Date: 09-Feb-2017
• Technical Committee: ERM TGDMR - Digital Mobile Radio
• Current Stage: 12 - Citation in the OJ
• Due Date: 09-Feb-2017
• Completion Date: 10-Feb-2017
• Ref Project: SIST EN 301 166 V2.1.1:2017 - Land mobile service - Radio equipment for analogue and/or digital communication (speech and/or data) and operating on narrow band channels and having an antenna connector - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Land mobile service - Radio equipment for analogue and/or digital communication (speech and/or data) and operating on narrow band channels and having an antenna connector - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU33.070.01Mobilni servisi na splošnoMobile services in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:ETSI EN 301 166 V2.1.1 (2016-11)SIST EN 301 166 V2.1.1:2017en01-januar-2017SIST EN 301 166 V2.1.1:2017SLOVENSKI
STANDARD



SIST EN 301 166 V2.1.1:2017



ETSI EN 301 166 V2.1.1 (2016-11) Land Mobile Service; Radio equipment for analogue and/or digital communication (speech and/or data) and operating on narrow band channels and having an antenna connector; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 301 166 V2.1.1:2017



ETSI ETSI EN 301 166 V2.1.1 (2016-11) 2
Reference REN/ERM-TGDMR-344 Keywords analogue, antenna, connector, data, digital, mobile, PMR, radio, speech ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: [phone]
Fax: [phone]
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 166 V2.1.1:2017



ETSI ETSI EN 301 166 V2.1.1 (2016-11) 3 Contents Intellectual Property Rights . 8 Foreword . 8 Modal verbs terminology . 8 1 Scope . 9 2 References . 9 2.1 Normative references . 9 2.2 Informative references . 10 3 Definitions, symbols and abbreviations . 11 3.1 Definitions . 11 3.2 Symbols . 12 3.3 Abbreviations . 13 4 General . 13 4.1 Testing . 13 4.1.0 Presentation of equipment for testing purposes . 13 4.1.1 Choice of model for testing . 13 4.1.1.0 General . 13 4.1.1.1 Auxiliary test equipment . 14 4.1.1.2 Declarations by the manufacturer . 14 4.2 Mechanical and electrical design . 14 4.2.1 General . 14 4.2.2 Controls . 14 4.2.3 Transmitter shut-off facility . 14 4.3 Testing using bit streams or messages . 14 4.4 Measuring continuous mode equipment . 14 4.5 Measuring discontinuous mode equipment . 14 4.6 Constant and non-constant envelope modulation . 15 4.7 Environmental profile . 15 5 Test conditions, power sources and ambient temperatures . 15 5.1 Normal and extreme test conditions . 15 5.2 Test power source . 15 5.3 Normal test conditions . 15 5.3.1 Normal temperature and humidity . 15 5.3.2 Normal test power source . 16 5.3.2.1 Mains voltage . 16 5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 16 5.3.2.3 Other power sources . 16 5.4 Extreme test conditions . 16 5.4.1 Extreme temperatures . 16 5.4.2 Extreme test source voltages . 16 5.4.2.1 Mains voltage . 16 5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 16 5.4.2.3 Power sources using other types of batteries . 16 5.4.2.4 Other power sources . 17 5.5 Procedure for tests at extreme temperatures . 17 5.5.0 Thermal balance . 17 5.5.1 Procedure for equipment designed for continuous transmission. 17 5.5.2 Procedure for equipment designed for intermittent transmission . 17 5.5.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) . 18 6 General conditions of measurement . 18 6.1 Test signals . 18 6.1.1 Transmitter test signals . 18 6.1.1.0 General . 18 SIST EN 301 166 V2.1.1:2017



ETSI ETSI EN 301 166 V2.1.1 (2016-11) 4 6.1.1.1 Analogue signals (B1) . 18 6.1.1.2 Digital signals (M5, M7) . 18 6.1.2 Receiver test signal for analogue equipment . 19 6.1.3 Receiver test signals for data (and digitized voice) equipment (M2), (M3), (M4) and (M6) . 19 6.1.4 Transmitter effective radiated power test signal (C1) . 19 6.2 Test load (artificial antenna) . 19 6.3 PEP . 19 6.4 Encoders . 19 6.5 Modulation processing . 20 6.6 Test sites and general arrangements for radiated measurements . 20 6.7 Transmitter automatic shut-off facility . 20 6.8 Arrangement for analogue test signals at the input of the transmitter . 20 6.9 Arrangement for test signals at the input of the receiver . 20 6.10 Receiver mute or squelch facility . 20 6.11 Receiver rated audio output power . 20 6.12 Facilities for access . 20 6.12.1 Analogue access . 20 6.12.2 Test points for bit stream measurements. 21 6.12.3 Coupling arrangements . 21 6.12.3.0 General . 21 6.12.3.1 Arrangements for measurements with continuous bit streams . 21 6.12.3.2 Arrangements for measurements with messages . 21 6.12.4 Modes of operation of the transmitter . 21 6.13 Duplex equipment . 21 7 Technical characteristics of the transmitter . 22 7.1 Maximum power (PX) (conducted) . 22 7.1.0 General . 22 7.1.1 Definition . 22 7.1.2 Method of measurement . 22 7.1.3 Limit . 22 7.2 Maximum effective radiated power . 22 7.2.1 Definition . 22 7.2.2 Method of measurement . 22 7.2.2.0 General . 22 7.2.2.1 Evaluation of CW-to-PEP correction factor for signal C1 . 23 7.2.2.2 Measurements on a test site . 23 7.2.3 Limit . 24 7.3 Adjacent and alternate channels power . 24 7.3.1 Definition . 24 7.3.2 Methods of measurement . 25 7.3.3 Limit . 25 7.4 Unwanted emissions in the spurious domain. 26 7.4.1 Definition . 26 7.4.2 Method of measurement . 26 7.4.2.1 Method of measuring conducted spurious emissions (clause 7.4.1 a)) in a specified load . 26 7.4.2.2 Method of measuring the effective radiated power with an external antenna connector (clause 7.4.1 b)) . 27 7.4.2.3 Method of measuring the effective radiated power with an integral antenna (clause 7.4.1 c)) . 28 7.4.3 Limits . 28 7.5 Intermodulation attenuation. 29 7.5.1 Definition . 29 7.5.2 Method of measurement . 29 7.5.3 Limits . 30 7.6 Transient power . 30 7.6.1 Definition . 30 7.6.2 Method of measurement . 30 7.6.2.0 Method . 30 7.6.2.1 Characteristics of the transient power measuring device . 31 7.6.3 Limits . 32 7.7 Frequency error . 32 7.7.0 General . 32 SIST EN 301 166 V2.1.1:2017



ETSI ETSI EN 301 166 V2.1.1 (2016-11) 5 7.7.1 Definition . 32 7.7.2 Method of measurement . 32 7.7.3 Limits . 33 7.8 Transmitter timeout timer . 33 7.8.1 Definition . 33 7.8.2 Method of measurement . 33 7.8.3 Limits . 33 8 Technical characteristics of the receiver . 34 8.1 Maximum usable sensitivity (analogue, conducted) . 34 8.1.1 Definition . 34 8.1.2 Method of measuring the SINAD ratio . 34 8.1.3 Limits . 34 8.2 Maximum usable sensitivity (analogue, field strength) . 34 8.2.1 Definition . 34 8.2.2 Method of measurement . 35 8.2.3 Limits . 36 8.3 Maximum usable sensitivity (digital, conducted) . 36 8.3.1 Definition . 36 8.3.2 Methods of measurement . 36 8.3.2.1 Method of measurement with continuous bit streams . 36 8.3.2.2 Method of measurement with messages . 37 8.3.3 Limits . 37 8.4 Maximum usable sensitivity (digital, field strength) . 38 8.4.1 Definition . 38 8.4.2 Method of measurement . 38 8.4.2.0 General . 38 8.4.2.1 Method of measurement with continuous bit streams . 38 8.4.2.2 Method of measurement with messages . 39 8.4.3 Limits . 40 8.5 Adjacent channel selectivity . 41 8.5.1 Definition . 41 8.5.2 Method of measurement . 41 8.5.2.0 General . 41 8.5.2.1 Method of measurement (analogue) . 41 8.5.2.2 Method of measurement (digital with continuous bit stream) . 42 8.5.2.3 Method of measurement with messages . 43 8.5.3 Limits . 44 8.6 Spurious response rejection . 44 8.6.1 Definition . 44 8.6.2 Method of measurement . 44 8.6.2.1 Introduction to the method of measurement . 44 8.6.2.2 Method of search over the "limited frequency range" . 45 8.6.2.3 Method of measurement (analogue) . 45 8.6.2.4 Method of measurement (digital with continuous bit streams) . 46 8.6.2.5 Method of measurement (digital with messages) . 47 8.6.3 Limits . 48 8.7 Intermodulation response rejection . 48 8.7.1 Definition . 48 8.7.2 Method of measurement . 48 8.7.2.1 Method of measurement (analogue) . 48 8.7.2.2 Method of measurement (digital with continuous bit stream) . 49 8.7.2.3 Method of measurement with messages . 50 8.7.3 Limit . 51 8.8 Blocking or desensitization . 51 8.8.1 Definition . 51 8.8.2 Method of measurement .
...

ETSI EN 301 166 V2.1.1 (2016-11)






HARMONISED EUROPEAN STANDARD
Land Mobile Service;
Radio equipment for analogue and/or digital communication
(speech and/or data) and operating on narrow band channels
and having an antenna connector;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 ETSI EN 301 166 V2.1.1 (2016-11)



Reference
REN/ERM-TGDMR-344
Keywords
analogue, antenna, connector, data, digital,
mobile, PMR, radio, speech

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 301 166 V2.1.1 (2016-11)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 12
3.3 Abbreviations . 13
4 General . 13
4.1 Testing . 13
4.1.0 Presentation of equipment for testing purposes . 13
4.1.1 Choice of model for testing . 13
4.1.1.0 General . 13
4.1.1.1 Auxiliary test equipment . 14
4.1.1.2 Declarations by the manufacturer . 14
4.2 Mechanical and electrical design . 14
4.2.1 General . 14
4.2.2 Controls . 14
4.2.3 Transmitter shut-off facility . 14
4.3 Testing using bit streams or messages . 14
4.4 Measuring continuous mode equipment . 14
4.5 Measuring discontinuous mode equipment . 14
4.6 Constant and non-constant envelope modulation . 15
4.7 Environmental profile . 15
5 Test conditions, power sources and ambient temperatures . 15
5.1 Normal and extreme test conditions . 15
5.2 Test power source . 15
5.3 Normal test conditions . 15
5.3.1 Normal temperature and humidity . 15
5.3.2 Normal test power source . 16
5.3.2.1 Mains voltage . 16
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 16
5.3.2.3 Other power sources . 16
5.4 Extreme test conditions . 16
5.4.1 Extreme temperatures . 16
5.4.2 Extreme test source voltages . 16
5.4.2.1 Mains voltage . 16
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 16
5.4.2.3 Power sources using other types of batteries . 16
5.4.2.4 Other power sources . 17
5.5 Procedure for tests at extreme temperatures . 17
5.5.0 Thermal balance . 17
5.5.1 Procedure for equipment designed for continuous transmission. 17
5.5.2 Procedure for equipment designed for intermittent transmission . 17
5.5.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna

equipment) . 18
6 General conditions of measurement . 18
6.1 Test signals . 18
6.1.1 Transmitter test signals . 18
6.1.1.0 General . 18
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 301 166 V2.1.1 (2016-11)
6.1.1.1 Analogue signals (B1) . 18
6.1.1.2 Digital signals (M5, M7) . 18
6.1.2 Receiver test signal for analogue equipment . 19
6.1.3 Receiver test signals for data (and digitized voice) equipment (M2), (M3), (M4) and (M6) . 19
6.1.4 Transmitter effective radiated power test signal (C1) . 19
6.2 Test load (artificial antenna) . 19
6.3 PEP . 19
6.4 Encoders . 19
6.5 Modulation processing . 20
6.6 Test sites and general arrangements for radiated measurements . 20
6.7 Transmitter automatic shut-off facility . 20
6.8 Arrangement for analogue test signals at the input of the transmitter . 20
6.9 Arrangement for test signals at the input of the receiver . 20
6.10 Receiver mute or squelch facility . 20
6.11 Receiver rated audio output power . 20
6.12 Facilities for access . 20
6.12.1 Analogue access . 20
6.12.2 Test points for bit stream measurements. 21
6.12.3 Coupling arrangements . 21
6.12.3.0 General . 21
6.12.3.1 Arrangements for measurements with continuous bit streams . 21
6.12.3.2 Arrangements for measurements with messages . 21
6.12.4 Modes of operation of the transmitter . 21
6.13 Duplex equipment . 21
7 Technical characteristics of the transmitter . 22
7.1 Maximum power (PX) (conducted) . 22
7.1.0 General . 22
7.1.1 Definition . 22
7.1.2 Method of measurement . 22
7.1.3 Limit . 22
7.2 Maximum effective radiated power . 22
7.2.1 Definition . 22
7.2.2 Method of measurement . 22
7.2.2.0 General . 22
7.2.2.1 Evaluation of CW-to-PEP correction factor for signal C1 . 23
7.2.2.2 Measurements on a test site . 23
7.2.3 Limit . 24
7.3 Adjacent and alternate channels power . 24
7.3.1 Definition . 24
7.3.2 Methods of measurement . 25
7.3.3 Limit . 25
7.4 Unwanted emissions in the spurious domain. 26
7.4.1 Definition . 26
7.4.2 Method of measurement . 26
7.4.2.1 Method of measuring conducted spurious emissions (clause 7.4.1 a)) in a specified load . 26
7.4.2.2 Method of measuring the effective radiated power with an external antenna connector

(clause 7.4.1 b)) . 27
7.4.2.3 Method of measuring the effective radiated power with an integral antenna (clause 7.4.1 c)) . 28
7.4.3 Limits . 28
7.5 Intermodulation attenuation. 29
7.5.1 Definition . 29
7.5.2 Method of measurement . 29
7.5.3 Limits . 30
7.6 Transient power . 30
7.6.1 Definition . 30
7.6.2 Method of measurement . 30
7.6.2.0 Method . 30
7.6.2.1 Characteristics of the transient power measuring device . 31
7.6.3 Limits . 32
7.7 Frequency error . 32
7.7.0 General . 32
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 301 166 V2.1.1 (2016-11)
7.7.1 Definition . 32
7.7.2 Method of measurement . 32
7.7.3 Limits . 33
7.8 Transmitter timeout timer . 33
7.8.1 Definition . 33
7.8.2 Method of measurement . 33
7.8.3 Limits . 33
8 Technical characteristics of the receiver . 34
8.1 Maximum usable sensitivity (analogue, conducted) . 34
8.1.1 Definition . 34
8.1.2 Method of measuring the SINAD ratio . 34
8.1.3 Limits . 34
8.2 Maximum usable sensitivity (analogue, field strength) . 34
8.2.1 Definition . 34
8.2.2 Method of measurement . 35
8.2.3 Limits . 36
8.3 Maximum usable sensitivity (digital, conducted) . 36
8.3.1 Definition . 36
8.3.2 Methods of measurement . 36
8.3.2.1 Method of measurement with continuous bit streams . 36
8.3.2.2 Method of measurement with messages . 37
8.3.3 Limits . 37
8.4 Maximum usable sensitivity (digital, field strength) . 38
8.4.1 Definition . 38
8.4.2 Method of measurement . 38
8.4.2.0 General . 38
8.4.2.1 Method of measurement with continuous bit streams . 38
8.4.2.2 Method of measurement with messages . 39
8.4.3 Limits . 40
8.5 Adjacent channel selectivity . 41
8.5.1 Definition . 41
8.5.2 Method of measurement . 41
8.5.2.0 General . 41
8.5.2.1 Method of measurement (analogue) . 41
8.5.2.2 Method of measurement (digital with continuous bit stream) . 42
8.5.2.3 Method of measurement with messages . 43
8.5.3 Limits . 44
8.6 Spurious response rejection . 44
8.6.1 Definition . 44
8.6.2 Method of measurement . 44
8.6.2.1 Introduction to the method of measurement . 44
8.6.2.2 Method of search over the "limited frequency range" . 45
8.6.2.3 Method of measurement (analogue) . 45
8.6.2.4 Method of measurement (digital with continuous bit streams) . 46
8.6.2.5 Method of measurement (digital with messages) . 47
8.6.3 Limits . 48
8.7 Intermodulation response rejection . 48
8.7.1 Definition . 48
8.7.2 Method of measurement . 48
8.7.2.1 Method of measurement (analogue) . 48
8.7.2.2 Method of measurement (digital with continuous bit stream) . 49
8.7.2.3 Method of measurement with messages . 50
8.7.3 Limit . 51
8.8 Blocking or desensitization . 51
8.8.1 Definition . 51
8.8.2 Method of measurement . 51
8.8.2.1 Method of measurement (analogue) . 51
8.8.2.2 Method of measurement (digital with continuous bit stream) . 52
8.8.2.3 Method of measuremen
...

Final draft ETSI EN 301 166 V2.1.1 (2016-07)






HARMONISED EUROPEAN STANDARD
Land Mobile Service;
Radio equipment for analogue and/or digital communication
(speech and/or data) and operating on narrow band channels
and having an antenna connector;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 166 V2.1.1 (2016-07)



Reference
REN/ERM-TGDMR-344
Keywords
analogue, antenna, connector, data, digital,
mobile, PMR, radio, speech

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 166 V2.1.1 (2016-07)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 12
3.3 Abbreviations . 13
4 General . 14
4.1 Testing . 14
4.1.0 Presentation of equipment for testing purposes . 14
4.1.1 Choice of model for testing . 14
4.1.1.0 General . 14
4.1.1.1 Auxiliary test equipment . 14
4.1.1.2 Declarations by the manufacturer . 14
4.2 Mechanical and electrical design . 14
4.2.1 General . 14
4.2.2 Controls . 14
4.2.3 Transmitter shut-off facility . 15
4.3 Testing using bit streams or messages . 15
4.4 Measuring continuous mode equipment . 15
4.5 Measuring discontinuous mode equipment . 15
4.6 Constant and non-constant envelope modulation . 15
4.7 Environmental profile . 15
5 Test conditions, power sources and ambient temperatures . 15
5.1 Normal and extreme test conditions . 15
5.2 Test power source . 16
5.3 Normal test conditions . 16
5.3.1 Normal temperature and humidity . 16
5.3.2 Normal test power source . 16
5.3.2.1 Mains voltage . 16
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 16
5.3.2.3 Other power sources . 16
5.4 Extreme test conditions . 17
5.4.1 Extreme temperatures . 17
5.4.2 Extreme test source voltages . 17
5.4.2.1 Mains voltage . 17
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 17
5.4.2.3 Power sources using other types of batteries . 17
5.4.2.4 Other power sources . 17
5.5 Procedure for tests at extreme temperatures . 18
5.5.0 Thermal balance . 18
5.5.1 Procedure for equipment designed for continuous transmission. 18
5.5.2 Procedure for equipment designed for intermittent transmission . 18
5.5.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna

equipment) . 18
6 General conditions of measurement . 19
6.1 Test signals . 19
6.1.1 Transmitter test signals . 19
6.1.1.0 General . 19
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 166 V2.1.1 (2016-07)
6.1.1.1 Analogue signals (B1) . 19
6.1.1.2 Digital signals (M5, M7) . 19
6.1.2 Receiver test signal for analogue equipment . 19
6.1.3 Receiver test signals for data (and digitized voice) equipment (M2), (M3), (M4) and (M6) . 20
6.1.4 Transmitter effective radiated power test signal (C1) . 20
6.2 Test load (artificial antenna) . 20
6.3 PEP . 20
6.4 Encoders . 20
6.5 Modulation processing . 20
6.6 Test sites and general arrangements for radiated measurements . 21
6.7 Transmitter automatic shut-off facility . 21
6.8 Arrangement for analogue test signals at the input of the transmitter . 21
6.9 Arrangement for test signals at the input of the receiver . 21
6.10 Receiver mute or squelch facility . 21
6.11 Receiver rated audio output power . 21
6.12 Facilities for access . 21
6.12.1 Analogue access . 21
6.12.2 Test points for bit stream measurements. 21
6.12.3 Coupling arrangements . 22
6.12.3.0 General . 22
6.12.3.1 Arrangements for measurements with continuous bit streams . 22
6.12.3.2 Arrangements for measurements with messages . 22
6.12.4 Modes of operation of the transmitter . 22
6.13 Duplex equipment . 22
7 Technical characteristics of the transmitter . 23
7.1 Maximum power (PX) (conducted) . 23
7.1.0 General . 23
7.1.1 Definition . 23
7.1.2 Method of measurement . 23
7.1.3 Limit . 23
7.2 Maximum effective radiated power . 23
7.2.1 Definition . 23
7.2.2 Method of measurement . 23
7.2.2.0 General . 23
7.2.2.1 Evaluation of CW-to-PEP correction factor for signal C1 . 24
7.2.2.2 Measurements on a test site . 24
7.2.3 Limit . 25
7.3 Adjacent and alternate channels power . 25
7.3.1 Definition . 25
7.3.2 Methods of measurement . 26
7.3.3 Limit . 26
7.4 Unwanted emissions in the spurious domain. 27
7.4.1 Definition . 27
7.4.2 Method of measurement . 27
7.4.2.1 Method of measuring conducted spurious emissions (clause 7.4.1 a)) in a specified load . 27
7.4.2.2 Method of measuring the effective radiated power with an external antenna connector

(clause 7.4.1 b)) . 28
7.4.2.3 Method of measuring the effective radiated power with an integral antenna (clause 7.4.1 c)) . 29
7.4.3 Limits . 29
7.5 Intermodulation attenuation. 30
7.5.1 Definition . 30
7.5.2 Method of measurement . 30
7.5.3 Limits . 31
7.6 Transient power . 31
7.6.1 Definition . 31
7.6.2 Method of measurement . 32
7.6.2.0 Method . 32
7.6.2.1 Characteristics of the transient power measuring device . 33
7.6.3 Limits . 33
7.7 Frequency error . 33
7.7.0 General . 33
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 166 V2.1.1 (2016-07)
7.7.1 Definition . 33
7.7.2 Method of measurement . 34
7.7.3 Limits . 34
7.8 Transmitter timeout timer . 35
7.8.1 Definition . 35
7.8.2 Method of measurement . 35
7.8.3 Limits . 35
8 Technical characteristics of the receiver . 35
8.1 Maximum usable sensitivity (analogue, conducted) . 35
8.1.1 Definition . 35
8.1.2 Method of measuring the SINAD ratio . 35
8.1.3 Limits . 36
8.2 Maximum usable sensitivity (analogue, field strength) . 36
8.2.1 Definition . 36
8.2.2 Method of measurement . 36
8.2.3 Limits . 37
8.3 Maximum usable sensitivity (digital, conducted) . 38
8.3.1 Definition . 38
8.3.2 Methods of measurement . 38
8.3.2.1 Method of measurement with continuous bit streams . 38
8.3.2.2 Method of measurement with messages . 38
8.3.3 Limits . 39
8.4 Maximum usable sensitivity (digital, field strength) . 39
8.4.1 Definition . 39
8.4.2 Method of measurement . 39
8.4.2.0 General . 39
8.4.2.1 Method of measurement with continuous bit streams . 40
8.4.2.2 Method of measurement with messages . 41
8.4.3 Limits . 42
8.5 Adjacent channel selectivity . 42
8.5.1 Definition . 42
8.5.2 Method of measurement . 42
8.5.2.0 General . 42
8.5.2.1 Method of measurement (analogue) . 43
8.5.2.2 Method of measurement (digital with continuous bit stream) . 43
8.5.2.3 Method of measurement with messages . 44
8.5.3 Limits . 45
8.6 Spurious response rejection . 45
8.6.1 Definition . 45
8.6.2 Method of measurement . 45
8.6.2.1 Introduction to the method of measurement . 45
8.6.2.2 Method of search over the "limited frequency range" . 46
8.6.2.3 Method of measurement (analogue) . 47
8.6.2.4 Method of measurement (digital with continuous bit streams) . 47
8.6.2.5 Method of measurement (digital with messages) . 48
8.6.3 Limits . 49
8.7 Intermodulation response rejection . 49
8.7.1 Definition . 49
8.7.2 Method of measurement . 49
8.7.2.1 Method of measurement (analogue) . 49
8.7.2.2 Method of measurement (digital with continuous bit stream) . 50
8.7.2.3 Method of measurement with messages . 51
8.7.3 Limit . 52
8.8 Blocking or desensitization . 52
8.8.1 Definition . 52
8.8.2 Method of measurement . 52
8.8.2.1 Method of measurement (analogue) . 52
8.8.2.2 Method of measurement (digital with continuous bit stream) .
...

Draft ETSI EN 301 166 V2.1.0 (2015-12)






HARMONISED EUROPEAN STANDARD
Land mobile service;
Radio equipment for analogue and/or digital communication
(speech and/or data) and operating on narrow band channels
and having an antenna connector;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 166 V2.1.0 (2015-12)



Reference
REN/ERM-TGDMR-344
Keywords
analogue, antenna, connector, data, digital,
mobile, PMR, radio, speech

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2015.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 166 V2.1.0 (2015-12)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 12
3.3 Abbreviations . 13
4 General . 13
4.1 Testing . 13
4.1.0 Presentation of equipment for testing purposes . 13
4.1.1 Choice of model for testing . 13
4.1.1.0 General . 13
4.1.1.1 Auxiliary test equipment . 14
4.1.1.2 Declarations by the supplier . 14
4.2 Mechanical and electrical design . 14
4.2.1 General . 14
4.2.2 Controls . 14
4.2.3 Transmitter shut-off facility . 14
4.3 Marking . 14
4.4 Testing using bit streams or messages . 14
4.5 Measuring continuous mode equipment . 14
4.6 Measuring discontinuous mode equipment . 14
4.7 Constant and non-constant envelope modulation . 15
4.8 Environmental profile . 15
5 Test conditions, power sources and ambient temperatures . 15
5.1 Normal and extreme test conditions . 15
5.2 Test power source . 15
5.3 Normal test conditions . 15
5.3.1 Normal temperature and humidity . 15
5.3.2 Normal test power source . 16
5.3.2.1 Mains voltage . 16
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 16
5.3.2.3 Other power sources . 16
5.4 Extreme test conditions . 16
5.4.1 Extreme temperatures . 16
5.4.2 Extreme test source voltages . 16
5.4.2.1 Mains voltage . 16
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 16
5.4.2.3 Power sources using other types of batteries . 16
5.4.2.4 Other power sources . 17
5.5 Procedure for tests at extreme temperatures . 17
5.5.0 Thermal balance . 17
5.5.1 Procedure for equipment designed for continuous transmission. 17
5.5.2 Procedure for equipment designed for intermittent transmission . 17
5.5.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 17
6 General conditions of measurement . 18
6.1 Test signals . 18
6.1.1 Transmitter test signals . 18
6.1.1.0 General . 18
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 166 V2.1.0 (2015-12)
6.1.1.1 Analogue signals (B1) . 18
6.1.1.2 Digital signals (M5, M7) . 18
6.1.2 Receiver test signal for analogue equipment . 18
6.1.3 Receiver test signals for data (and digitized voice) equipment (M2), (M3), (M4) and (M6) . 19
6.1.4 Transmitter effective radiated power test signal (C1) . 19
6.2 Test load (artificial antenna) . 19
6.3 PEP . 19
6.4 Encoders . 19
6.5 Modulation processing . 19
6.6 Test sites and general arrangements for radiated measurements . 19
6.7 Transmitter automatic shut-off facility . 20
6.8 Arrangement for analogue test signals at the input of the transmitter . 20
6.9 Arrangement for test signals at the input of the receiver . 20
6.10 Receiver mute or squelch facility . 20
6.11 Receiver rated audio output power . 20
6.12 Facilities for access . 20
6.12.1 Analogue access . 20
6.12.2 Test points for bit stream measurements. 20
6.12.3 Coupling arrangements . 21
6.12.3.0 General . 21
6.12.3.1 Arrangements for measurements with continuous bit streams . 21
6.12.3.2 Arrangements for measurements with messages . 21
6.12.4 Modes of operation of the transmitter . 21
6.13 Duplex equipment . 21
7 Technical characteristics of the transmitter . 21
7.1 Maximum power (PX) (conducted) . 21
7.1.0 General . 21
7.1.1 Definition . 21
7.1.2 Method of measurement . 21
7.1.3 Limit . 22
7.2 Maximum effective radiated power . 22
7.2.1 Definition . 22
7.2.2 Method of measurement . 22
7.2.2.0 General . 22
7.2.2.1 Evaluation of CW-to-PEP correction factor for signal C1 . 22
7.2.2.2 Measurements on a test site . 22
7.2.3 Limit . 23
7.3 Adjacent and alternate channels power . 24
7.3.1 Definition . 24
7.3.2 Methods of measurement . 24
7.3.3 Limit . 25
7.4 Unwanted emissions in the spurious domain. 25
7.4.1 Definition . 25
7.4.2 Method of measurement . 26
7.4.2.1 Method of measuring conducted spurious emissions (clause 7.4.1 a)) in a specified load . 26
7.4.2.2 Method of measuring the effective radiated power with an external antenna connector

(clause 7.4.1 b)) . 26
7.4.2.3 Method of measuring the effective radiated power with an integral antenna (clause 7.4.1 c)) . 27
7.4.3 Limits . 27
7.5 Intermodulation attenuation. 28
7.5.1 Definition . 28
7.5.2 Method of measurement . 29
7.5.3 Limits . 30
7.6 Transient power . 30
7.6.1 Definition . 30
7.6.2 Method of measurement . 30
7.6.2.0 Method . 30
7.6.2.1 Characteristics of the transient power measuring device . 31
7.6.3 Limits . 31
7.7 Frequency error . 31
7.7.0 General . 31
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 166 V2.1.0 (2015-12)
7.7.1 Definition . 31
7.7.2 Method of measurement . 32
7.7.3 Limits . 32
7.8 Transmitter timeout timer . 32
7.8.1 Definition . 32
7.8.2 Method of measurement . 33
7.7.3 Limits . 33
8 Technical characteristics of the receiver . 33
8.1 Maximum usable sensitivity (analogue, conducted) . 33
8.1.1 Definition . 33
8.1.2 Method of measuring the SINAD ratio . 33
8.1.3 Limits . 34
8.2 Maximum usable sensitivity (analogue, field strength) . 34
8.2.1 Definition . 34
8.2.2 Method of measurement . 34
8.2.3 Limits . 35
8.3 Maximum usable sensitivity (digital, conducted) . 35
8.3.1 Definition . 35
8.3.2 Methods of measurement . 35
8.3.2.1 Method of measurement with continuous bit streams . 35
8.3.2.2 Method of measurement with messages . 36
8.3.3 Limits . 36
8.4 Maximum usable sensitivity (digital, field strength) . 37
8.4.1 Definition . 37
8.4.2 Method of measurement . 37
8.4.2.0 General . 37
8.4.2.1 Method of measurement with continuous bit streams . 37
8.4.2.2 Method of measurement with messages . 38
8.4.3 Limits . 39
8.5 Adjacent channel selectivity . 40
8.5.1 Definition . 40
8.5.2 Method of measurement . 40
8.5.2.0 General . 40
8.5.2.1 Method of measurement (analogue) . 40
8.5.2.2 Method of measurement (digital with continuous bit stream) . 41
8.5.2.3 Method of measurement with messages . 42
8.5.3 Limits . 43
8.6 Spurious response rejection . 43
8.6.1 Definition . 43
8.6.2 Method of measurement . 43
8.6.2.1 Introduction to the method of measurement . 43
8.6.2.2 Method of search over the "limited frequency range" . 44
8.6.2.3 Method of measurement (analogue) . 44
8.6.2.4 Method of measurement (digital with continuous bit streams) . 45
8.6.2.5 Method of measurement (digital with messages) . 46
8.6.3 Limits . 46
8.7 Intermodulation response rejection . 47
8.7.1 Definition . 47
8.7.2 Method of measurement . 47
8.7.2.1 Method of measurement (analogue) . 47
8.7.2.2 Method of measurement (digital with continuous bit stream) . 48
8.7.2.3 Method of measurement with messages . 48
8.7.3 Limit . 50
8.8 Blocking or desensitization . 50
8.8.1 Definition . 50
8.8.2 Method of measurement . 50
8.8.2.1 Method of measurement (analogue) .
...