ETSI EN 303 204 V2.1.2 (2016-09)
Network Based Short Range Devices (SRD); Radio equipment to be used in the 870 MHz to 876 MHz frequency range with power levels ranging up to 500 mW; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
Network Based Short Range Devices (SRD); Radio equipment to be used in the 870 MHz to 876 MHz frequency range with power levels ranging up to 500 mW; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
REN/ERM-TG28-536
Omrežne naprave kratkega dosega (SRD) - Radijska oprema, ki se uporablja v frekvenčnem območju od 870 MHz do 876 MHz z močnostnimi nivoji do največ 500 mW - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU
Ta dokument se uporablja za radijsko opremo naslednjih vrst:
1) Omrežne naprave kratkega dosega (SRD), namenjene za delovanje v povezavi z drugimi napravami kratkega dosega, da se oblikujejo omrežne topologije, ki podpirajo predvideno vrsto uporabe.
2) Omrežne relejne točke, tj. specifične omrežne naprave kratkega dosega, ki podpirajo medsebojno povezovanje omrežja naprav kratkega dosega z zunanjim omrežjem ali storitvijo.
Ta dokument zajema opremo, namenjeno za uporabo na stalni lokaciji, opremo, ki je običajno nameščena v vozilu, in opremo, namenjeno za prenašanje ali pritrditev.
Ta dokument vsebuje zahteve, s katerimi se dokazuje, da radijska oprema optimalno uporablja in tudi podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivega motenja.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.(8Network Based Short Range Devices (SRD) - Radio equipment to be used in the 870 MHz to 876 MHz frequency range with power levels ranging up to 500 mW - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:ETSI EN 303 204 V2.1.2 (2016-09)SIST EN 303 204 V2.1.2:2016en01-november-2016SIST EN 303 204 V2.1.2:2016SLOVENSKI
STANDARD
SIST EN 303 204 V2.1.2:2016
ETSI EN 303 204 V2.1.2 (2016-09) Network Based Short Range Devices (SRD); Radio equipment to be used in the 870 MHz to 876 MHz frequency range with power levels ranging up to 500 mW; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 303 204 V2.1.2:2016
ETSI ETSI EN 303 204 V2.1.2 (2016-09) 2
Reference REN/ERM-TG28-536 Keywords harmonised standard, radio, SRD, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 303 204 V2.1.2:2016
ETSI ETSI EN 303 204 V2.1.2 (2016-09) 3 Contents Intellectual Property Rights . 9 Foreword . 9 Modal verbs terminology . 9 Introduction . 9 1 Scope . 12 2 References . 12 2.1 Normative references . 12 2.2 Informative references . 13 3 Definitions, symbols and abbreviations . 13 3.1 Definitions . 13 3.2 Symbols . 15 3.3 Abbreviations . 16 4 Technical requirements specifications . 16 4.1 Environmental profile . 16 4.2 General requirements . 17 4.2.1 General considerations . 17 4.2.2 Performance criteria . 17 4.2.3 Limits . 17 4.3 Requirements for transmitters . 18 4.3.1 Frequency Tolerance. 18 4.3.1.1 Applicability. 18 4.3.1.2 Description . 18 4.3.1.3 Limits . 18 4.3.1.4 Conformance . 18 4.3.2 Effective radiated power . 18 4.3.2.1 Applicability. 18 4.3.2.2 Description . 18 4.3.2.3 Limits . 18 4.3.2.4 Conformance . 18 4.3.3 Transient power . 19 4.3.3.1 Applicability. 19 4.3.3.2 Description . 19 4.3.3.3 Limits . 19 4.3.3.4 Conformance . 19 4.3.4 Occupied bandwidth . 19 4.3.4.1 Applicability. 19 4.3.4.2 Description . 19 4.3.4.3 Limits . 19 4.3.4.4 Conformance . 19 4.3.5 Unwanted emissions in the out-of-band domain . 20 4.3.5.1 Applicability. 20 4.3.5.2 Description . 20 4.3.5.3 Limits . 21 4.3.5.4 Conformance . 21 4.3.6 Unwanted emissions in the spurious domain . 21 4.3.6.1 Applicability. 21 4.3.6.2 Description . 22 4.3.6.3 Limits . 22 4.3.6.4 Conformance . 22 4.3.7 Frequency stability under low-voltage conditions . 22 4.3.7.1 Applicability. 22 4.3.7.2 Description . 22 4.3.7.3 Limits . 23 4.3.7.4 Conformance . 23 SIST EN 303 204 V2.1.2:2016
ETSI ETSI EN 303 204 V2.1.2 (2016-09) 4 4.3.8 Duty cycle . 23 4.3.8.1 Applicability. 23 4.3.8.2 Description . 23 4.3.8.3 Duty cycle . 23 4.3.8.4 Short term behaviour . 23 4.3.8.5 Limits . 24 4.3.8.6 Conformance . 24 4.3.9 Automatic/Adaptive Power Control . 24 4.3.9.1 Applicability. 24 4.3.9.2 Description . 24 4.3.9.3 Limits . 24 4.3.9.4 Conformance . 24 4.4 Requirements for receivers . 24 4.4.1 Receiver sensitivity . 24 4.4.1.1 Applicability. 24 4.4.1.2 Description . 24 4.4.1.3 Limits . 25 4.4.1.4 Conformance . 25 4.4.2 Clear channel assessment threshold . 25 4.4.2.1 Applicability. 25 4.4.2.2 Description . 25 4.4.2.3 Limits . 25 4.4.2.4 Conformance . 25 4.4.3 Adjacent channel selectivity . 25 4.4.3.1 Applicability. 25 4.4.3.2 Description . 26 4.4.3.3 Limits . 26 4.4.3.4 Conformance . 26 4.4.4 Blocking . 26 4.4.4.1 Applicability. 26 4.4.4.2 Description . 26 4.4.4.3 Limits . 26 4.4.4.4 Conformance . 26 4.4.5 Receiver spurious radiations . 26 4.4.5.1 Applicability. 26 4.4.5.2 Description . 27 4.4.5.3 Limits . 27 4.4.5.4 Conformance . 27 4.5 Requirements for spectrum access . 27 4.5.1 General limits . 27 4.5.2 Listen before talk . 27 4.5.2.1 Applicability. 27 4.5.2.2 Description . 27 4.5.2.3 Limits . 28 4.5.2.4 Conformance . 28 4.6 Other requirements . 28 4.6.1 Channel adaptivity . 28 4.6.1.1 Applicability. 28 4.6.1.2 Description . 28 4.6.1.3 Limits . 28 4.6.1.4 Conformance . 28 4.6.2 Short control signalling transmissions . 28 4.6.2.1 Applicability. 28 4.6.2.2 Description . 29 4.6.2.3 Limits . 29 4.6.2.4 Conformance . 29 4.6.3 Coordination of network relay points . 29 4.6.3.1 Applicability. 29 4.6.3.2 Description . 29 4.6.3.3 Limits . 29 4.6.3.4 Conformance . 30 SIST EN 303 204 V2.1.2:2016
ETSI ETSI EN 303 204 V2.1.2 (2016-09) 5 5 Testing for compliance with technical requirements . 30 5.1 Environmental conditions for testing . 30 5.2 General conditions for testing . 30 5.2.1 General considerations . 30 5.2.2 Provider declared information . 30 5.2.3 Presentation of equipment for testing purposes . 31 5.2.3.1 General Considerations . 31 5.2.3.2 Choice of model for testing . 31 5.2.3.2.1 General considerations . 31 5.2.3.2.2 EUT with an external RF connector . 32 5.2.3.2.3 EUT without an external RF connector . 32 5.2.3.3 Testing of modular equipment . 32 5.2.3.4 Transmitter shut-off facility . 33 5.2.3.5 Battery saving circuit . 33 5.2.3.6 Test power source . 33 5.2.3.6.1 General considerations . 33 5.2.3.6.2 External test power source . 33 5.2.3.6.3 Internal test power source . 33 5.2.4 Normal and extreme test conditions. 33 5.2.4.1 Normal temperature and humidity . 33 5.2.4.2 Extreme temperatures . 34 5.2.4.2.1 Procedure for tests at extreme temperatures . 34 5.2.4.2.2 Procedure for equipment designed for continuous operation . 34 5.2.4.2.3 Procedure for equipment designed for intermittent operation . 34 5.2.4.2.4 Extreme temperature ranges . 34 5.2.4.3 Normal test power source . 35 5.2.4.3.1 Mains voltage . 35 5.2.4.3.2 Regulated lead-acid battery power sources . 35 5.2.4.3.3 Other power sources . 35 5.2.4.4 Extreme test source voltages . 35 5.2.4.4.1 Mains voltage . 35 5.2.4.4.2 Regulated lead-acid battery power sources . 35 5.2.4.4.3 Power sources using other types of batteries . 35 5.2.4.4.4 Other power sources . 36 5.2.5 Conducted measurements . 36 5.2.5.1 Artificial antenna . 36 5.2.5.2 Voltage Standing Wave Ratio (VSWR) . 36 5.2.6 Radiated measurements . 36 5.2.7 Measuring receiver . 36 5.2.7.1 General considerations . 36 5.2.7.2 Reference Bandwidth . 37 5.2.8 Transmitter test signals . 37 5.2.9 Applicable measurement methods . 38 5.2.10 Modes of operation . 39 5.2.10.1 Test mode . 39 5.2.10.2 Transmitter operation . 39 5.2.10.3 Testing of multi-frequency or channel agile equipment . 40 5.2.10.4 Non-uniform maximum transmit power . 40 5.3 Interpretation of the measurement results . 40 5.4 Conformance methods of measurement for transmitters . 41 5.4.1 Frequency tolerance . 41 5.4.1.1 Test conditions . 41 5.
...
ETSI EN 303 204 V2.1.2 (2016-09)
HARMONISED EUROPEAN STANDARD
Network Based Short Range Devices (SRD);
Radio equipment to be used in the 870 MHz to 876 MHz
frequency range with power levels ranging up to 500 mW;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 303 204 V2.1.2 (2016-09)
Reference
REN/ERM-TG28-536
Keywords
harmonised standard, radio, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 303 204 V2.1.2 (2016-09)
Contents
Intellectual Property Rights . 9
Foreword . 9
Modal verbs terminology . 9
Introduction . 9
1 Scope . 12
2 References . 12
2.1 Normative references . 12
2.2 Informative references . 13
3 Definitions, symbols and abbreviations . 13
3.1 Definitions . 13
3.2 Symbols . 15
3.3 Abbreviations . 16
4 Technical requirements specifications . 16
4.1 Environmental profile . 16
4.2 General requirements . 17
4.2.1 General considerations . 17
4.2.2 Performance criteria . 17
4.2.3 Limits . 17
4.3 Requirements for transmitters . 18
4.3.1 Frequency Tolerance. 18
4.3.1.1 Applicability. 18
4.3.1.2 Description . 18
4.3.1.3 Limits . 18
4.3.1.4 Conformance . 18
4.3.2 Effective radiated power . 18
4.3.2.1 Applicability. 18
4.3.2.2 Description . 18
4.3.2.3 Limits . 18
4.3.2.4 Conformance . 18
4.3.3 Transient power . 19
4.3.3.1 Applicability. 19
4.3.3.2 Description . 19
4.3.3.3 Limits . 19
4.3.3.4 Conformance . 19
4.3.4 Occupied bandwidth . 19
4.3.4.1 Applicability. 19
4.3.4.2 Description . 19
4.3.4.3 Limits . 19
4.3.4.4 Conformance . 19
4.3.5 Unwanted emissions in the out-of-band domain . 20
4.3.5.1 Applicability. 20
4.3.5.2 Description . 20
4.3.5.3 Limits . 21
4.3.5.4 Conformance . 21
4.3.6 Unwanted emissions in the spurious domain . 21
4.3.6.1 Applicability. 21
4.3.6.2 Description . 22
4.3.6.3 Limits . 22
4.3.6.4 Conformance . 22
4.3.7 Frequency stability under low-voltage conditions . 22
4.3.7.1 Applicability. 22
4.3.7.2 Description . 22
4.3.7.3 Limits . 23
4.3.7.4 Conformance . 23
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 303 204 V2.1.2 (2016-09)
4.3.8 Duty cycle . 23
4.3.8.1 Applicability. 23
4.3.8.2 Description . 23
4.3.8.3 Duty cycle . 23
4.3.8.4 Short term behaviour . 23
4.3.8.5 Limits . 24
4.3.8.6 Conformance . 24
4.3.9 Automatic/Adaptive Power Control . 24
4.3.9.1 Applicability. 24
4.3.9.2 Description . 24
4.3.9.3 Limits . 24
4.3.9.4 Conformance . 24
4.4 Requirements for receivers . 24
4.4.1 Receiver sensitivity . 24
4.4.1.1 Applicability. 24
4.4.1.2 Description . 24
4.4.1.3 Limits . 25
4.4.1.4 Conformance . 25
4.4.2 Clear channel assessment threshold . 25
4.4.2.1 Applicability. 25
4.4.2.2 Description . 25
4.4.2.3 Limits . 25
4.4.2.4 Conformance . 25
4.4.3 Adjacent channel selectivity . 25
4.4.3.1 Applicability. 25
4.4.3.2 Description . 26
4.4.3.3 Limits . 26
4.4.3.4 Conformance . 26
4.4.4 Blocking . 26
4.4.4.1 Applicability. 26
4.4.4.2 Description . 26
4.4.4.3 Limits . 26
4.4.4.4 Conformance . 26
4.4.5 Receiver spurious radiations . 26
4.4.5.1 Applicability. 26
4.4.5.2 Description . 27
4.4.5.3 Limits . 27
4.4.5.4 Conformance . 27
4.5 Requirements for spectrum access . 27
4.5.1 General limits . 27
4.5.2 Listen before talk . 27
4.5.2.1 Applicability. 27
4.5.2.2 Description . 27
4.5.2.3 Limits . 28
4.5.2.4 Conformance . 28
4.6 Other requirements . 28
4.6.1 Channel adaptivity . 28
4.6.1.1 Applicability. 28
4.6.1.2 Description . 28
4.6.1.3 Limits . 28
4.6.1.4 Conformance . 28
4.6.2 Short control signalling transmissions . 28
4.6.2.1 Applicability. 28
4.6.2.2 Description . 29
4.6.2.3 Limits . 29
4.6.2.4 Conformance . 29
4.6.3 Coordination of network relay points . 29
4.6.3.1 Applicability. 29
4.6.3.2 Description . 29
4.6.3.3 Limits . 29
4.6.3.4 Conformance . 30
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 303 204 V2.1.2 (2016-09)
5 Testing for compliance with technical requirements . 30
5.1 Environmental conditions for testing . 30
5.2 General conditions for testing . 30
5.2.1 General considerations . 30
5.2.2 Provider declared information . 30
5.2.3 Presentation of equipment for testing purposes . 31
5.2.3.1 General Considerations . 31
5.2.3.2 Choice of model for testing . 31
5.2.3.2.1 General considerations . 31
5.2.3.2.2 EUT with an external RF connector . 32
5.2.3.2.3 EUT without an external RF connector . 32
5.2.3.3 Testing of modular equipment . 32
5.2.3.4 Transmitter shut-off facility . 33
5.2.3.5 Battery saving circuit . 33
5.2.3.6 Test power source . 33
5.2.3.6.1 General considerations . 33
5.2.3.6.2 External test power source . 33
5.2.3.6.3 Internal test power source . 33
5.2.4 Normal and extreme test conditions. 33
5.2.4.1 Normal temperature and humidity . 33
5.2.4.2 Extreme temperatures . 34
5.2.4.2.1 Procedure for tests at extreme temperatures . 34
5.2.4.2.2 Procedure for equipment designed for continuous operation . 34
5.2.4.2.3 Procedure for equipment designed for intermittent operation . 34
5.2.4.2.4 Extreme temperature ranges . 34
5.2.4.3 Normal test power source . 35
5.2.4.3.1 Mains voltage . 35
5.2.4.3.2 Regulated lead-acid battery power sources . 35
5.2.4.3.3 Other power sources . 35
5.2.4.4 Extreme test source voltages . 35
5.2.4.4.1 Mains voltage . 35
5.2.4.4.2 Regulated lead-acid battery power sources . 35
5.2.4.4.3 Power sources using other types of batteries . 35
5.2.4.4.4 Other power sources . 36
5.2.5 Conducted measurements . 36
5.2.5.1 Artificial antenna . 36
5.2.5.2 Voltage Standing Wave Ratio (VSWR) . 36
5.2.6 Radiated measurements . 36
5.2.7 Measuring receiver . 36
5.2.7.1 General considerations . 36
5.2.7.2 Reference Bandwidth . 37
5.2.8 Transmitter test signals . 37
5.2.9 Applicable measurement methods . 38
5.2.10 Modes of operation . 39
5.2.10.1 Test mode . 39
5.2.10.2 Transmitter operation . 39
5.2.10.3 Testing of multi-frequency or channel agile equipment . 40
5.2.10.4 Non-uniform maximum transmit power . 40
5.3 Interpretation of the measurement results . 40
5.4 Conformance methods of measurement for transmitters . 41
5.4.1 Frequency tolerance . 41
5.4.1.1 Test conditions . 41
5.4.1.2 Radiated measurement . 41
5.4.1.3 Conducted measurement . 41
5.4.1.4 Alternate conducted measurement .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.