ETSI EN 301 908-2 V7.1.1 (2015-12)
IMT cellular networks; Harmonised EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)
IMT cellular networks; Harmonised EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)
REN/MSG-TFES-011-02
Celična omrežja IMT - Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE - 2. del: CDMA z neposrednim razprševanjem (“Direct Spread”) (UTRA FDD) (UE)
Ta dokument zajema zahteve za uporabniško opremo UTRA FDD iz izdaj 99, 4, 5, 6, 7, 8, 9, 10 in 11 dokumenta 3GPP, kot je določeno v dokumentu ETSI TS 125 101 [5]. To vključuje zahteve za pasove, v katerih deluje UE iz izdaje 12 dokumenta 3GPP, kot je določeno v dokumentu ETSI TS 125 101 [i.12]. Poleg tega ta dokument zajema zahteve za uporabniško opremo UTRA FDD, ki deluje v frekvenčnih pasovih, določenih v dokumentu ETSI TS 102 735 [i.4].
OPOMBA 1: Za pas XX:
- Za uporabniško opremo, zasnovano kot mobilno ali nomadsko, so zahteve iz tega dokumenta, izmerjene na antenskem vhodu, tudi v skladu z ustrezno zahtevo, opredeljeno kot TRP (skupna sevana moč), kot je opisana v Sklepu Komisije 2010/267/EU [i.7], Sklepu Odbora za elektronske komunikacije (09)03 [i.8] in poročilu CEPT 30 [i.9].
- Za uporabniško opremo, zasnovano za priključitev ali namestitev, ta dokument ne obravnava zahtev, opisanih v Sklepu Komisije 2010/267/EU [i.7], Sklepu Odbora za elektronske komunikacije (09)03 [i.8] in poročilu CEPT 30 [i.9].
Ta dokument zajema določbe člena 3.2 Direktive 1999/5/ES [i.2] (direktive R&TTE), ki navaja, da »/.../ mora biti radijska oprema skonstruirana tako, da učinkovito uporablja spekter, razporejen za prizemne/vesoljske radijske komunikacije in orbitalne vire, tako da ne pride do škodljivega motenja.«
Poleg tega dokumenta se lahko za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov člena 3 direktive R&TTE [i.2].
General Information
Standards Content (Sample)
Draft ETSI EN 301 908-2 V7.0.1 (2015-05)
HARMONIZED EUROPEAN STANDARD
IMT cellular networks;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive;
Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)
2 Draft ETSI EN 301 908-2 V7.0.1 (2015-05)
ReRefeferreencncee
RREENN//MMSSGG--TTFES-011-02FES-011-02
KKeeyywwords ords
3G3G, 3G, 3GPP, cePP, cellullular, dlar, diigigital,tal, IM IMTT,, mobil mobilee, rad, radiio, o,
regularegulattioion, Un, UMMTTSS, U, UTTRRAA, , WWCCDDMMAA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Draft ETSI EN 301 908-2 V7.0.1 (2015-05)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 11
3.3 Abbreviations . 12
4 Technical requirements specifications . 13
4.1 Environmental profile . 13
4.2 Conformance requirements . 13
4.2.1 Introduction. 13
4.2.2 Transmitter maximum output power. 14
4.2.2.1 Transmitter maximum output power . 14
4.2.2.1.1 Definition. 14
4.2.2.1.2 Limits . 14
4.2.2.1.3 Conformance . 14
4.2.2.2 Transmitter maximum output power for DC-HSUPA . 15
4.2.2.2.1 Definition for DC-HSUPA . 15
4.2.2.2.2 Limits for DC-HSUPA . 15
4.2.2.2.3 Conformance . 15
4.2.2.3 Transmitter maximum output power for UL OLTD . 15
4.2.2.3.1 Definition for UL OLTD . 15
4.2.2.3.2 Limits for UL OLTD . 15
4.2.2.3.3 Conformance . 16
4.2.3 Transmitter spectrum emission mask . 16
4.2.3.1 Transmitter spectrum emission mask . 16
4.2.3.1.1 Definition. 16
4.2.3.1.2 Limits . 16
4.2.3.1.3 Conformance . 16
4.2.3.2 Transmitter spectrum emission mask for DC-HSUPA . 17
4.2.3.2.1 Definition for DC-HSUPA . 17
4.2.3.2.2 Limits for DC-HSUPA . 17
4.2.3.2.3 Conformance . 17
4.2.3.3 Transmitter spectrum emission mask for UL OLTD . 17
4.2.3.3.1 Definition for UL OLTD . 17
4.2.3.3.2 Limits for UL OLTD . 17
4.2.3.3.3 Conformance . 18
4.2.3.4 Transmitter spectrum emission mask for UL CLTD Activation state 1 . 18
4.2.3.4.1 Definition for UL CLTD Activation state 1 . 18
4.2.3.4.2 Limits for UL CLTD Activation state 1 . 18
4.2.3.4.3 Conformance . 19
4.2.4 Transmitter spurious emis sions . 19
4.2.4.1 Transmitter spurious emissions . 19
4.2.4.1.1 Definition. 19
4.2.4.1.2 Limits . 19
4.2.4.1.3 Conformance . 21
4.2.4.2 Transmitter spurious emissions for DC-HSUPA . 21
4.2.4.2.1 Definition for DC-HSUPA . 21
4.2.4.2.2 Limits for DC-HSUPA . 21
ETSI
4 Draft ETSI EN 301 908-2 V7.0.1 (2015-05)
4.2.4.2.3 Conformance . 23
4.2.5 Transmitter minimum output power . 24
4.2.5.1 Transmitter minimum output power. 24
4.2.5.1.1 Definition. 24
4.2.5.1.2 Limits . 24
4.2.5.1.3 Conformance . 24
4.2.5.2 Transmitter minimum output power for DC-HSUPA . 24
4.2.5.2.1 Definition for DC-HSUPA . 24
4.2.5.2.2 Limits for DC-HSUPA . 24
4.2.5.2.3 Conformance . 24
4.2.5.3 Transmitter minimum output power for UL CLTD Activation state 1 . 24
4.2.5.3.1 Definition for UL CLTD Activation state 1 . 24
4.2.5.3.2 Limits for UL CLTD Activation state 1 . 24
4.2.5.3.3 Conformance . 24
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 24
4.2.6.1 Definition . 24
4.2.6.2 Limits . 25
4.2.6.3 Conformance . 25
4.2.7 Receiver blocking characteristics . 25
4.2.7.1 Definition . 25
4.2.7.2 Limits . 25
4.2.7.3 Conformance . 27
4.2.8 Receiver spurious response . 27
4.2.8.1 Definition . 27
4.2.8.2 Limits . 27
4.2.8.3 Conformance . 27
4.2.9 Receiver intermodulation characteristics . 27
4.2.9.1 Definition . 27
4.2.9.2 Limits . 27
4.2.9.3 Conformance . 28
4.2.10 Receiver spurious emissions . 28
4.2.10.1 Definition . 28
4.2.10.2 Limits . 28
4.2.10.3 Conformance . 30
4.2.11 Out-of-synchronization handling of output power . 30
4.2.11.1 Definition . 30
4.2.11.2 Limits . 30
4.2.11.3 Conformance . 32
4.2.12 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 32
4.2.12.1 Transmitter adjacent channel leakage power ratio (ACLR) . 32
4.2.12.1.1 Definition. 32
4.2.12.1.2 Limits . 32
4.2.12.1.3 Conformance . 32
4.2.12.2 Adjacent channel leakage power ratio for DC-HSUPA . 32
4.2.12.2.1 Definition for DC-HSUPA . 32
4.2.12.2.2 Limits for DC-HSUPA . 32
4.2.12.2.3 Conformance . 32
4.2.12.3 Adjacent channel leakage power ratio for UL OLTD . 33
4.2.12.3.1 Definition for UL OLTD . 33
4.2.12.3.2 Limits for UL OLTD . 33
4.2.12.3.3 Conformance . 33
4.2.12.4 Adjacent channel leakage power ratio for UL CLTD Activation state 1 . 33
4.2.12.4.1 Definition for UL CLTD Activation state 1 . 33
4.2.12.4.2 Limits for UL CLTD Activation state 1 . 33
4.2.12.4.3 Conformance . 33
5 Testing for compliance with technical requirements . 34
5.1 Environmental conditions for testing . 34
5.2 Interpretation of the measurement results . 34
5.3 Essential radio test suites . 35
5.3.1 Transmitter maximum output power. 35
5.3.1.1 Method of test . 35
ETSI
5 Draft ETSI EN 301 908-2 V7.0.1 (2015-05)
5.3.1.1.1 UTRA . 35
5.3.1.1.1A DC-HSUPA . 36
5.3.1.1.1B UL OLTD . 36
5.3.1.2 Test requirements . 37
5.3.2 Transmitter spectrum emission mask . 37
5.3.2.1 Method of test . 37
5.3.2.1.1 UEs not supporting HSDPA and/or E-DCH . 37
5.3.2.1.1A UEs supporting HSDPA and/or E-DCH . 38
5.3.2.1.1B DC-HSUPA . 38
5.3.2.1.1C UL OLTD . 39
5.3.2.1.1D UL CLTD Activation state 1 . 39
5.3.2.2 Test requirements . 40
5.3.3 Transmitter spurious emis sions . 40
5.3.3.1 Method of test . 40
5.3.3.1.1 UTRA . 40
5.3.3.1.1A DC-HSUPA . 41
5.3.3.2 Test requirements . 41
5.3.4 Transmitter minimum output power . 41
5.3.4.1 Method of test . 41
5.3.4.1.1 UTRA . 41
5.3.4.1.1A DC-HSUPA . 42
5.3.4.1.1B UL CLTD Activation state 1 . 42
5.3.4.2 Test requirements . 42
5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 43
5.3.5.1 Method of test . 43
5.3.5.1.1 Initial conditions . 43
5.3.5.1.2 Procedure . 43
5.3.5.2 Test requirements . 43
5.3.6 Receiver blocking characteristics . 43
5.3.6.1 Method of test . 43
5.3.6.1.1 Initial requirements . 43
5.3.6.1.2 Procedure . 44
5.3.6.2 Test requirements . 44
5.3.7 Receiver spurious response . 44
5.3.7.1 Method of test . 44
5.3.7.1.1 Initial conditions . 44
5.3.7.1.2 Procedure . 44
5.3.7.2 Test requirements . 44
5.3.8 Receiver Intermodulation characteristics . 45
5.3.8.1 Method of test . 45
5.3.8.1.1 Initial conditions . 45
5.3.8.1.2 Procedure . 45
5.3.8.2 Test requirements . 45
5.3.9 Receiver spurious emissions . 45
5.3.9.1 Method of test . 45
5.3.9.1.1 Initial conditions . 45
5.3.9.1.2 Procedure . 45
5.3.9.2 Test requirements . 45
5.3.10 Out-of-synchronization handling of output power . 46
5.3.10.1 Method of test . 46
5.3.10.1.1 Initial conditions . 46
5.3.10.1.2 Procedure . 46
5.3.10.2 Test requirements . 46
5.3.11 Transmitter adjacent channel leakage power ratio . 46
5.3.11.1 Method of test . 46
5.3.11.1.1 UEs not supporting HSDPA and/or E-DCH . 46
5.3.11.1.1A UEs supporting HSDPA and/or E-DCH . 47
5.3.11.1.1B DC-HSUPA . 47
5.3.11.1.1C UL OLTD . 48
5.3.11.1.1D UL CLTD Activation state 1 . 49
5.3.11.2 Test requirements . 49
ETSI
6 Draft ETSI EN 301 908-2 V7.0.1 (2015-05)
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 50
Annex B (normative): Environmental profile . 52
B.1 General . 52
B.1.1 Introduction . 52
B.1.2 Temperature . 52
B.1.3 Voltage . 52
B.1.4 Test environment . 52
Annex C: Void . 53
Annex D (informative): Bibliography . 54
History . 55
ETSI
7 Draft ETSI EN 301 908-2 V7.0.1 (2015-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards
Group (MSG), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN
Approval Procedure.
The present document has been produced by ETSI in response to mandates M/284 and M/406 issued from the European
Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.10].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2].
The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 [10].
National transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in ETSI EG 201 399 [i.3].
ETSI
8 Draft ETSI EN 301 908-2 V7.0.1 (2015-05)
1 Scope
The present document applies to the following radio equipment type:
• User Equipment for IMT-2000 CDMA Direct Spread (UTRA FDD).
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1.
Table 1-1: UTRA FDD operating bands
UTRA FDD Band Direction of transmission UTRA FDD operating bands
I Transmit 1 920 MHz to 1 980 MHz
Receive 2 110 MHz to 2 170 MHz
III Transmit 1 710 MHz to 1 785 MHz
Receive 1 805 MHz to 1 880 MHz
VII Transmit 2 500 MHz to 2 570 MHz
Receive 2 620 MHz to 2 690 MHz
VIII Transmit 880 MHz to 915 MHz
Receive 925 MHz to 960 MHz
XV Transmit 1 900 MHz to 1 920 MHz
Receive 2 600 MHz to 2 620 MHz
XVI Transmit 2 010 MHz to 2 025 MHz
Receive 2 585 MHz to 2 600 MHz
XX Transmit 832 MHz to 862 MHz
Receive 791 MHz to 821 MHz
XXII Transmit 3 410 MHz to 3 490 MHz
Receive 3 510 MHz to 3 590 MHz
The present document covers requirements for UTRA FDD User Equipment from 3GPP Releases 99, 4, 5, 6, 7, 8, 9, 10,
and 11 defined in ETSI TS 125 101 [5]. This includes the requirements for UE operating bands from 3GPP Release 12
defined in ETSI TS 125 101 [11]. In addition, the present document covers requirements for UTRA FDD User
Equipment in the operating bands specified in ETSI TS 102 735 [i.4].
NOTE 1: For Band XX:
- for user equipment designed to be mobile or nomadic, the requirements in the present document
measured at the antenna port also show conformity to the corresponding requirement defined as
TRP (Total Radiated Power), as described in Commission Decision 2010/267/EU [i.7],
ECC Decision (09)03 [i.8] and CEPT Report 30 [i.9];
- for user equipment designed to be fixed or installed, the present document does not address the
requirements described in Commission Decision 2010/267/EU [i.7], ECC Decision (09)03 [i.8] and
CEPT Report 30 [i.9].
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2,
which states that "radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
NOTE 2: A list of such ENs is included on the web site http://www.newapproach.org/.
ETSI
9 Draft ETSI EN 301 908-2 V7.0.1 (2015-05)
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Void.
[2] ETSI TS 134 121-1 (V11.6.0) (02-2015): "Universal Mobile Telecommunications System
(UMTS); User Equipment (UE) conformance specification; Radio transmission and reception
(FDD); Part 1: Conformance specification (3GPP TS 34.121-1 version 11.7.0 Release 11)".
[3] ETSI TS 134 108 (V11.13.0) (04-2015): "Universal Mobile Telecommunications System (UMTS);
LTE; Common test environments for User Equipment (UE); Conformance testing
(3GPP TS 34.108 version 11.13.0 Release 11)".
[4] ETSI TS 134 109 (V12.0.0) (09-2014): "Universal Mobile Telecommunications System (UMTS);
Terminal logical test interface; Special conformance testing functions (3GPP TS 34.109
version 12.0.0 Release 12)".
[5] ETSI TS 125 101 (V11.11.0) (01-2015): "Universal Mobile Telecommunications System (UMTS);
User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.101 version 11.11.0
Release 11)".
[6] IEC 60068-2-1 (03-2007): "Environmental testing - Part 2-1: Tests - Test A: Cold".
[7] IEC 60068-2-2 (07-2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[8] ETSI TS 125 214 (V11.11.0) (01-2015): "Universal Mobile Telecommunications System (UMTS);
Physical layer procedures (FDD) (3GPP TS 25.214 version 11.11.0 Release 11)".
[9] ETSI TS 145 004 (V11.0.0) (10-2012): "Digital cellular telecommunications system (Phase 2+);
Modulation (3GPP TS 45.004 version 11.0.0 Release 11)".
[10] ETSI EN 301 908-1 (V7.1.1) (03-2015): "IMT cellular networks; Harmonized EN covering the
essential requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common
requirements".
[11] ETSI TS 125 101 (V12.7.0) (04-2015): "Universal Mobile Telecommunications System (UMTS);
User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.101 version 12.7.0
Release 12)".
ETSI
10 Draft ETSI EN 301 908-2 V7.0.1 (2015-05)
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.3] ETSI EG 201 399 (V2.2.1) (08-2010): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); A guide to the production of Harmonized Standards for application under the
R&TTE Directive".
[i.4] ETSI TS 102 735 (V7.1.0): "Universal Mobile Telecommunications System (UMTS); Band-
specific requirements for UMTS Frequency Division Duplex (FDD) operation in the bands
1 900 MHz to 1 920 MHz paired with 2 600 MHz to 2 620 MHz and 2 010 MHz to 2 025 MHz
paired with 2 585 MHz to 2 600 MHz".
[i.5] Void.
[i.6] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[i.7] Commission Decision 2010/267/EU of 6 May 2010 on harmonised technical conditions of use in
the 790-862 MHz frequency band for terrestrial systems capable of providing electronic
communications services in the European Union.
[i.8] ECC Decision (09)03 of 30 October 2009 on harmonised conditions for mobile/fixed
communications networks (MFCN) operating in the band 790 - 862 MHz.
[i.9] CEPT Report 30 of 30 October 2009 to the European Commission in response to the Mandate on
"The identification of common and minimal (least restrictive) technical conditions for
790 - 862 MHz for the digital dividend in the European Union".
[i.10] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending
Directive 98/34/EC laying down a procedure for the provision of information in the field of
technical standards and regulations.
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
chip rate: rate of "chips" (modulated symbols after spreading) per second
NOTE: The UTRA FDD chip rate is 3,84 Mchip/s.
data rate: rate of the user information, which is transmitted over the Air Interface
EXAMPLE: Output rate of the voice codec.
enhanced performance receiver type 1 for DCH: receiver with performance requirements which are optional for the
UE and utilize receiver diversity during DCH reception
ETSI
11 Draft ETSI EN 301 908-2 V7.0.1 (2015-05)
environmental profile: range of environmental conditions under which equipment within the scope of the present
document is required to comply with the provisions of the present document
maximum output power: measure of the maximum power the UE can transmit (i.e. the actual power as would be
measured assuming no measurement error) in a bandwidth of at least (1 + α) times the chip rate of the radio access
mode
NOTE: The period of measurement is assumed to be at least one timeslot.
mean power: power (transmitted or received) in a bandwidth of at least (1 + α) times the chip rate of the radio access
mode, when applied to a WCDMA modulated signal
NOTE: The period of measurement is assumed to be at least one timeslot unless otherwise stated.
node B: logical node responsible for radio transmission/reception in one or more cells to/from the User Equipment
nominal maximum output power: nominal power defined by the UE power class
operating band: frequency range that is defined with a specific set of technical requirements, in which UTRA FDD
operates
NOTE: Operating bands for UTRA are designated with Roman numerals, while the corresponding operating
bands for E-UTRA are designated with Arabic numerals.
power spectral density: function of power versus frequency and when integrated across a
...
Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)
HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised EN covering the essential requirements
of article 3.2 of the R&TTE Directive;
Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)
2 Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)
Reference
REN/MSG-TFES-011-02
Keywords
3G, 3GPP, cellular, digital, IMT, mobile, radio,
regulation, UMTS, UTRA, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 11
3.3 Abbreviations . 12
4 Technical requirements specifications . 13
4.1 Environmental profile . 13
4.2 Conformance requirements . 13
4.2.1 Introduction. 13
4.2.2 Transmitter maximum output power. 14
4.2.2.1 Transmitter maximum output power . 14
4.2.2.1.1 Definition. 14
4.2.2.1.2 Limits . 14
4.2.2.1.3 Conformance . 14
4.2.2.2 Transmitter maximum output power for DC-HSUPA . 14
4.2.2.2.1 Definition for DC-HSUPA . 14
4.2.2.2.2 Limits for DC-HSUPA . 15
4.2.2.2.3 Conformance . 15
4.2.2.3 Transmitter maximum output power for UL OLTD . 15
4.2.2.3.1 Definition for UL OLTD . 15
4.2.2.3.2 Limits for UL OLTD . 15
4.2.2.3.3 Conformance . 15
4.2.3 Transmitter spectrum emission mask . 16
4.2.3.1 Transmitter spectrum emission mask . 16
4.2.3.1.1 Definition. 16
4.2.3.1.2 Limits . 16
4.2.3.1.3 Conformance . 16
4.2.3.2 Transmitter spectrum emission mask for DC-HSUPA . 16
4.2.3.2.1 Definition for DC-HSUPA . 16
4.2.3.2.2 Limits for DC-HSUPA . 16
4.2.3.2.3 Conformance . 17
4.2.3.3 Transmitter spectrum emission mask for UL OLTD . 17
4.2.3.3.1 Definition for UL OLTD . 17
4.2.3.3.2 Limits for UL OLTD . 17
4.2.3.3.3 Conformance . 17
4.2.3.4 Transmitter spectrum emission mask for UL CLTD Activation state 1 . 18
4.2.3.4.1 Definition for UL CLTD Activation state 1 . 18
4.2.3.4.2 Limits for UL CLTD Activation state 1 . 18
4.2.3.4.3 Conformance . 18
4.2.4 Transmitter spurious emis sions . 18
4.2.4.1 Transmitter spurious emissions . 18
4.2.4.1.1 Definition. 18
4.2.4.1.2 Limits . 18
4.2.4.1.3 Conformance . 20
4.2.4.2 Transmitter spurious emissions for DC-HSUPA . 20
4.2.4.2.1 Definition for DC-HSUPA . 20
4.2.4.2.2 Limits for DC-HSUPA . 20
ETSI
4 Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)
4.2.4.2.3 Conformance . 22
4.2.5 Transmitter minimum output power . 23
4.2.5.1 Transmitter minimum output power. 23
4.2.5.1.1 Definition. 23
4.2.5.1.2 Limits . 23
4.2.5.1.3 Conformance . 23
4.2.5.2 Transmitter minimum output power for DC-HSUPA . 23
4.2.5.2.1 Definition for DC-HSUPA . 23
4.2.5.2.2 Limits for DC-HSUPA . 23
4.2.5.2.3 Conformance . 23
4.2.5.3 Transmitter minimum output power for UL CLTD Activation state 1 . 23
4.2.5.3.1 Definition for UL CLTD Activation state 1 . 23
4.2.5.3.2 Limits for UL CLTD Activation state 1 . 23
4.2.5.3.3 Conformance . 23
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 23
4.2.6.1 Definition . 23
4.2.6.2 Limits . 24
4.2.6.3 Conformance . 24
4.2.7 Receiver blocking characteristics . 24
4.2.7.1 Definition . 24
4.2.7.2 Limits . 24
4.2.7.3 Conformance . 26
4.2.8 Receiver spurious response . 26
4.2.8.1 Definition . 26
4.2.8.2 Limits . 26
4.2.8.3 Conformance . 26
4.2.9 Receiver intermodulation characteristics . 26
4.2.9.1 Definition . 26
4.2.9.2 Limits . 26
4.2.9.3 Conformance . 27
4.2.10 Receiver spurious emissions . 27
4.2.10.1 Definition . 27
4.2.10.2 Limits . 27
4.2.10.3 Conformance . 28
4.2.11 Out-of-synchronization handling of output power . 28
4.2.11.1 Definition . 28
4.2.11.2 Limits . 28
4.2.11.3 Conformance . 30
4.2.12 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 30
4.2.12.1 Transmitter adjacent channel leakage power ratio (ACLR) . 30
4.2.12.1.1 Definition. 30
4.2.12.1.2 Limits . 30
4.2.12.1.3 Conformance . 30
4.2.12.2 Adjacent channel leakage power ratio for DC-HSUPA . 30
4.2.12.2.1 Definition for DC-HSUPA . 30
4.2.12.2.2 Limits for DC-HSUPA . 30
4.2.12.2.3 Conformance . 30
4.2.12.3 Adjacent channel leakage power ratio for UL OLTD . 31
4.2.12.3.1 Definition for UL OLTD . 31
4.2.12.3.2 Limits for UL OLTD . 31
4.2.12.3.3 Conformance . 31
4.2.12.4 Adjacent channel leakage power ratio for UL CLTD Activation state 1 . 31
4.2.12.4.1 Definition for UL CLTD Activation state 1 . 31
4.2.12.4.2 Limits for UL CLTD Activation state 1 . 31
4.2.12.4.3 Conformance . 31
5 Testing for compliance with technical requirements . 32
5.1 Environmental conditions for testing . 32
5.2 Interpretation of the measurement results . 32
5.3 Essential radio test suites . 33
5.3.1 Transmitter maximum output power. 33
5.3.1.1 Method of test . 33
ETSI
5 Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)
5.3.1.1.1 UTRA . 33
5.3.1.1.1A DC-HSUPA . 34
5.3.1.1.1B UL OLTD . 34
5.3.1.2 Test requirements . 35
5.3.2 Transmitter spectrum emission mask . 35
5.3.2.1 Method of test . 35
5.3.2.1.1 UEs not supporting HSDPA and/or E-DCH . 35
5.3.2.1.1A UEs supporting HSDPA and/or E-DCH . 36
5.3.2.1.1B DC-HSUPA . 36
5.3.2.1.1C UL OLTD . 36
5.3.2.1.1D UL CLTD Activation state 1 . 37
5.3.2.2 Test requirements . 38
5.3.3 Transmitter spurious emis sions . 38
5.3.3.1 Method of test . 38
5.3.3.1.1 UTRA . 38
5.3.3.1.1A DC-HSUPA . 38
5.3.3.2 Test requirements . 39
5.3.4 Transmitter minimum output power . 39
5.3.4.1 Method of test . 39
5.3.4.1.1 UTRA . 39
5.3.4.1.1A DC-HSUPA . 39
5.3.4.1.1B UL CLTD Activation state 1 . 40
5.3.4.2 Test requirements . 40
5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 40
5.3.5.1 Method of test . 40
5.3.5.1.1 Initial conditions . 40
5.3.5.1.2 Procedure . 41
5.3.5.2 Test requirements . 41
5.3.6 Receiver blocking characteristics . 41
5.3.6.1 Method of test . 41
5.3.6.1.1 Initial requirements . 41
5.3.6.1.2 Procedure . 41
5.3.6.2 Test requirements . 41
5.3.7 Receiver spurious response . 42
5.3.7.1 Method of test . 42
5.3.7.1.1 Initial conditions . 42
5.3.7.1.2 Procedure . 42
5.3.7.2 Test requirements . 42
5.3.8 Receiver Intermodulation characteristics . 42
5.3.8.1 Method of test . 42
5.3.8.1.1 Initial conditions . 42
5.3.8.1.2 Procedure . 43
5.3.8.2 Test requirements . 43
5.3.9 Receiver spurious emissions . 43
5.3.9.1 Method of test . 43
5.3.9.1.1 Initial conditions . 43
5.3.9.1.2 Procedure . 43
5.3.9.2 Test requirements . 43
5.3.10 Out-of-synchronization handling of output power . 43
5.3.10.1 Method of test . 43
5.3.10.1.1 Initial conditions . 43
5.3.10.1.2 Procedure . 44
5.3.10.2 Test requirements . 44
5.3.11 Transmitter adjacent channel leakage power ratio . 44
5.3.11.1 Method of test . 44
5.3.11.1.1 UEs not supporting HSDPA and/or E-DCH . 44
5.3.11.1.1A UEs supporting HSDPA and/or E-DCH . 45
5.3.11.1.1B DC-HSUPA . 45
5.3.11.1.1C UL OLTD . 45
5.3.11.1.1D UL CLTD Activation state 1 . 46
5.3.11.2 Test requirements . 47
ETSI
6 Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 48
Annex B (normative): Environmental profile . 50
B.1 General . 50
B.1.1 Introduction . 50
B.1.2 Temperature . 50
B.1.3 Voltage . 50
B.1.4 Test environment . 50
Annex C: Void . 51
Annex D (informative): Bibliography . 52
History . 53
ETSI
7 Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile
Standards Group (MSG), and is now submitted for the Vote phase of the ETSI standards EN Approval Procedure.
The present document has been produced by ETSI in response to mandates M/284 and M/406 issued from the European
Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.10].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonised Standard under the Directive 1999/5/EC [i.2].
The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.11].
National transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in ETSI EG 201 399 [i.3].
ETSI
8 Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)
1 Scope
The present document applies to the following radio equipment type:
• User Equipment for IMT-2000 CDMA Direct Spread (UTRA FDD).
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1.
Table 1-1: UTRA FDD operating bands
UTRA FDD Band Direction of transmission UTRA FDD operating bands
I Transmit 1 920 MHz to 1 980 MHz
Receive 2 110 MHz to 2 170 MHz
III Transmit 1 710 MHz to 1 785 MHz
Receive 1 805 MHz to 1 880 MHz
VII Transmit 2 500 MHz to 2 570 MHz
Receive 2 620 MHz to 2 690 MHz
VIII Transmit 880 MHz to 915 MHz
Receive 925 MHz to 960 MHz
XV Transmit 1 900 MHz to 1 920 MHz
Receive 2 600 MHz to 2 620 MHz
XVI Transmit 2 010 MHz to 2 025 MHz
Receive 2 585 MHz to 2 600 MHz
XX Transmit 832 MHz to 862 MHz
Receive 791 MHz to 821 MHz
XXII Transmit 3 410 MHz to 3 490 MHz
Receive 3 510 MHz to 3 590 MHz
The present document covers requirements for UTRA FDD User Equipment from 3GPP Releases 99, 4, 5, 6, 7, 8, 9, 10,
and 11 defined in ETSI TS 125 101 [5]. This includes the requirements for UE operating bands from 3GPP Release 12
defined in ETSI TS 125 101 [i.12]. In addition, the present document covers requirements for UTRA FDD User
Equipment in the operating bands specified in ETSI TS 102 735 [i.4].
NOTE 1: For Band XX:
- for user equipment designed to be mobile or nomadic, the requirements in the present document
measured at the antenna port also show conformity to the corresponding requirement defined as
TRP (Total Radiated Power), as described in Commission Decision 2010/267/EU [i.7],
ECC Decision (09)03 [i.8] and CEPT Report 30 [i.9];
- for user equipment designed to be fixed or installed, the present document does not address the
requirements described in Commission Decision 2010/267/EU [i.7], ECC Decision (09)03 [i.8] and
CEPT Report 30 [i.9].
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2,
which states that "radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
NOTE 2: A list of such ENs is included on the web site http://www.newapproach.org/.
ETSI
9 Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Void.
[2] ETSI TS 134 121-1 (V12.1.0) (10-2015): "Universal Mobile Telecommunications System
(UMTS); User Equipment (UE) conformance specification; Radio transmission and reception
(FDD); Part 1: Conformance specification (3GPP TS 34.121-1 version 12.1.0 Release 12)".
[3] ETSI TS 134 108 (V12.1.0) (10-2015): "Universal Mobile Telecommunications System (UMTS);
LTE; Common test environments for User Equipment (UE); Conformance testing
(3GPP TS 34.108 version 12.1.0 Release 12)".
[4] ETSI TS 134 109 (V12.0.0) (09-2014): "Universal Mobile Telecommunications System (UMTS);
Terminal logical test interface; Special conformance testing functions (3GPP TS 34.109
version 12.0.0 Release 12)".
[5] ETSI TS 125 101 (V11.11.0) (01-2015): "Universal Mobile Telecommunications System (UMTS);
User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.101 version 11.11.0
Release 11)".
[6] IEC 60068-2-1 (03-2007): "Environmental testing - Part 2-1: Tests - Test A: Cold".
[7] IEC 60068-2-2 (07-2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[8] ETSI TS 125 214 (V11.12.0) (07-2015): "Universal Mobile Telecommunications System (UMTS);
Physical layer procedures (FDD) (3GPP TS 25.214 version 11.12.0 Release 11)".
[9] ETSI TS 145 004 (V11.0.0) (10-2012): "Digital cellular telecommunications system (Phase 2+);
Modulation (3GPP TS 45.004 version 11.0.0 Release 11)".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
ETSI
10 Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)
[i.3] ETSI EG 201 399 (V2.2.1) (08-2010): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); A guide to the production of Harmonized Standards for application under the
R&TTE Directive".
[i.4] ETSI TS 102 735 (V7.1.0): "Universal Mobile Telecommunications System (UMTS);
Band-specific requirements for UMTS Frequency Division Duplex (FDD) operation in the bands
1 900 MHz to 1 920 MHz paired with 2 600 MHz to 2 620 MHz and 2 010 MHz to 2 025 MHz
paired with 2 585 MHz to 2 600 MHz".
[i.5] Void.
[i.6] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[i.7] Commission Decision 2010/267/EU of 6 May 2010 on harmonised technical conditions of use in
the 790-862 MHz frequency band for terrestrial systems capable of providing electronic
communications services in the European Union.
[i.8] ECC Decision (09)03 of 30 October 2009 on harmonised conditions for mobile/fixed
communications networks (MFCN) operating in the band 790 - 862 MHz.
[i.9] CEPT Report 30 of 30 October 2009 to the European Commission in response to the Mandate on
"The identification of common and minimal (least restrictive) technical conditions for
790 - 862 MHz for the digital dividend in the European Union".
[i.10] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending
Directive 98/34/EC laying down a procedure for the provision of information in the field of
technical standards and regulations.
[i.11] ETSI EN 301 908-1 (V7.1.1) (03-2015): "IMT cellular networks; Harmonized EN covering the
essential requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common
requirements".
[i.12] ETSI TS 125 101 (V12.9.0) (10-2015): "Universal Mobile Telecommunications System (UMTS);
User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.101 version 12.9.0
Release 12)".
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
chip rate: rate of "chips" (modulated symbols after spreading) per second
NOTE: The UTRA FDD chip rate is 3,84 Mchip/s.
data rate: rate of the user information, which is transmitted over the Air Interface
EXAMPLE: Output rate of the voice codec.
enhanced performance receiver type 1 for DCH: receiver with performance requirements which are optional for the
UE and utilize receiver diversity during DCH reception
environmental profile: range of environmental conditions under which equipment within the scope of the present
document is required to comply with the provisions of the present document
maximum output power: measure of the maximum power the UE can transmit (i.e. the actual power as would be
measured assuming no measurement error) in a bandwidth of at least (1 + α) times the chip rate of the radio access
mode
NOTE: The period of measurement is assumed to be at least one timeslot.
ETSI
11 Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)
mean power: power (transmitted or received) in a bandwidth of at least (1 + α) times the chip rate of the radio access
mode, when applied to a WCDMA modulated signal
NOTE: The period of measurement is assumed to be at least one timeslot unless otherwise stated.
node B: logical node responsible for radio transmission/reception in one or more cells to/from the User Equipment
nominal maximum output power: nominal power defined by the UE power class
operating band: frequency range that is defined with a specific set of technical requirements, in which UTRA FDD
operates
NOTE: Operating bands for UTRA are designated with Roman numerals, while the corresponding operating
bands for E-UTRA are designated with Arabic numerals.
power spectral density: function of power versus frequency and when integrated across a given bandwidth, the
function represents the mean power in s
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)33.070.99Druge mobilne storitveOther mobile services33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-2 V7.1.1SIST EN 301 908-2 V7.1.1:2016en01-marec-2016SIST EN 301 908-2 V7.1.1:2016SLOVENSKI
STANDARD
HARMONISED EUROPEAN STANDARD SIST EN 301 908-2 V7.1.1:2016
ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 2
Reference REN/MSG-TFES-011-02 Keywords 3G, 3GPP, cellular, digital, IMT, mobile, radio, regulation, UMTS, UTRA, WCDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-2 V7.1.1:2016
ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 Introduction . 7 1 Scope . 8 2 References . 9 2.1 Normative references . 9 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 10 3.1 Definitions . 10 3.2 Symbols . 11 3.3 Abbreviations . 12 4 Technical requirements specifications . 13 4.1 Environmental profile . 13 4.2 Conformance requirements . 13 4.2.1 Introduction. 13 4.2.2 Transmitter maximum output power. 14 4.2.2.1 Transmitter maximum output power . 14 4.2.2.1.1 Definition. 14 4.2.2.1.2 Limits . 14 4.2.2.1.3 Conformance . 14 4.2.2.2 Transmitter maximum output power for DC-HSUPA . 14 4.2.2.2.1 Definition for DC-HSUPA . 14 4.2.2.2.2 Limits for DC-HSUPA . 15 4.2.2.2.3 Conformance . 15 4.2.2.3 Transmitter maximum output power for UL OLTD . 15 4.2.2.3.1 Definition for UL OLTD . 15 4.2.2.3.2 Limits for UL OLTD . 15 4.2.2.3.3 Conformance . 15 4.2.3 Transmitter spectrum emission mask . 16 4.2.3.1 Transmitter spectrum emission mask . 16 4.2.3.1.1 Definition. 16 4.2.3.1.2 Limits . 16 4.2.3.1.3 Conformance . 16 4.2.3.2 Transmitter spectrum emission mask for DC-HSUPA . 16 4.2.3.2.1 Definition for DC-HSUPA . 16 4.2.3.2.2 Limits for DC-HSUPA . 16 4.2.3.2.3 Conformance . 17 4.2.3.3 Transmitter spectrum emission mask for UL OLTD . 17 4.2.3.3.1 Definition for UL OLTD . 17 4.2.3.3.2 Limits for UL OLTD . 17 4.2.3.3.3 Conformance . 17 4.2.3.4 Transmitter spectrum emission mask for UL CLTD Activation state 1 . 18 4.2.3.4.1 Definition for UL CLTD Activation state 1 . 18 4.2.3.4.2 Limits for UL CLTD Activation state 1 . 18 4.2.3.4.3 Conformance . 18 4.2.4 Transmitter spurious emissions . 18 4.2.4.1 Transmitter spurious emissions . 18 4.2.4.1.1 Definition. 18 4.2.4.1.2 Limits . 18 4.2.4.1.3 Conformance . 20 4.2.4.2 Transmitter spurious emissions for DC-HSUPA . 20 4.2.4.2.1 Definition for DC-HSUPA . 20 4.2.4.2.2 Limits for DC-HSUPA . 20 SIST EN 301 908-2 V7.1.1:2016
ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 4 4.2.4.2.3 Conformance . 22 4.2.5 Transmitter minimum output power . 23 4.2.5.1 Transmitter minimum output power. 23 4.2.5.1.1 Definition. 23 4.2.5.1.2 Limits . 23 4.2.5.1.3 Conformance . 23 4.2.5.2 Transmitter minimum output power for DC-HSUPA . 23 4.2.5.2.1 Definition for DC-HSUPA . 23 4.2.5.2.2 Limits for DC-HSUPA . 23 4.2.5.2.3 Conformance . 23 4.2.5.3 Transmitter minimum output power for UL CLTD Activation state 1 . 23 4.2.5.3.1 Definition for UL CLTD Activation state 1 . 23 4.2.5.3.2 Limits for UL CLTD Activation state 1 . 23 4.2.5.3.3 Conformance . 23 4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 23 4.2.6.1 Definition . 23 4.2.6.2 Limits . 24 4.2.6.3 Conformance . 24 4.2.7 Receiver blocking characteristics . 24 4.2.7.1 Definition . 24 4.2.7.2 Limits . 24 4.2.7.3 Conformance . 26 4.2.8 Receiver spurious response . 26 4.2.8.1 Definition . 26 4.2.8.2 Limits . 26 4.2.8.3 Conformance . 26 4.2.9 Receiver intermodulation characteristics . 26 4.2.9.1 Definition . 26 4.2.9.2 Limits . 26 4.2.9.3 Conformance . 27 4.2.10 Receiver spurious emissions . 27 4.2.10.1 Definition . 27 4.2.10.2 Limits . 27 4.2.10.3 Conformance . 28 4.2.11 Out-of-synchronization handling of output power . 28 4.2.11.1 Definition . 28 4.2.11.2 Limits . 28 4.2.11.3 Conformance . 30 4.2.12 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 30 4.2.12.1 Transmitter adjacent channel leakage power ratio (ACLR) . 30 4.2.12.1.1 Definition. 30 4.2.12.1.2 Limits . 30 4.2.12.1.3 Conformance . 30 4.2.12.2 Adjacent channel leakage power ratio for DC-HSUPA . 30 4.2.12.2.1 Definition for DC-HSUPA . 30 4.2.12.2.2 Limits for DC-HSUPA . 30 4.2.12.2.3 Conformance . 30 4.2.12.3 Adjacent channel leakage power ratio for UL OLTD . 31 4.2.12.3.1 Definition for UL OLTD . 31 4.2.12.3.2 Limits for UL OLTD . 31 4.2.12.3.3 Conformance . 31 4.2.12.4 Adjacent channel leakage power ratio for UL CLTD Activation state 1 . 31 4.2.12.4.1 Definition for UL CLTD Activation state 1 . 31 4.2.12.4.2 Limits for UL CLTD Activation state 1 . 31 4.2.12.4.3 Conformance . 31 5 Testing for compliance with technical requirements . 32 5.1 Environmental conditions for testing . 32 5.2 Interpretation of the measurement results . 32 5.3 Essential radio test suites . 33 5.3.1 Transmitter maximum output power. 33 5.3.1.1 Method of test . 33 SIST EN 301 908-2 V7.1.1:2016
ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 5 5.3.1.1.1 UTRA . 33 5.3.1.1.1A DC-HSUPA . 34 5.3.1.1.1B UL OLTD . 34 5.3.1.2 Test requirements . 35 5.3.2 Transmitter spectrum emission mask . 35 5.3.2.1 Method of test . 35 5.3.2.1.1 UEs not supporting HSDPA and/or E-DCH . 35 5.3.2.1.1A UEs supporting HSDPA and/or E-DCH . 36 5.3.2.1.1B DC-HSUPA . 36 5.3.2.1.1C UL OLTD . 36 5.3.2.1.1D UL CLTD Activation state 1 . 37 5.3.2.2 Test requirements . 38 5.3.3 Transmitter spurious emissions . 38 5.3.3.1 Method of test . 38 5.3.3.1.1 UTRA . 38 5.3.3.1.1A DC-HSUPA . 38 5.3.3.2 Test requirements . 39 5.3.4 Transmitter minimum output power . 39 5.3.4.1 Method of test . 39 5.3.4.1.1 UTRA . 39 5.3.4.1.1A DC-HSUPA . 39 5.3.4.1.1B UL CLTD Activation state 1 . 40 5.3.4.2 Test requirements . 40 5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 40 5.3.5.1 Method of test . 40 5.3.5.1.1 Initial conditions . 40 5.3.5.1.2 Procedure . 41 5.3.5.2 Test requirements . 41 5.3.6 Receiver blocking characteristics . 41 5.3.6.1 Method of test . 41 5.3.6.1.1 Initial requirements . 41 5.3.6.1.2 Procedure . 41 5.3.6.2 Test requirements . 41 5.3.7 Receiver spurious response . 42 5.3.7.1 Method of test . 42 5.3.7.1.1 Initial conditions . 42 5.3.7.1.2 Procedure . 42 5.3.7.2 Test requirements . 42 5.3.8 Receiver Intermodulation characteristics . 42 5.3.8.1 Method of test . 42 5.3.8.1.1 Initial conditions . 42 5.3.8.1.2 Procedure . 43 5.3.8.2 Test requirements . 43 5.3.9 Receiver spurious emissions . 43 5.3.9.1 Method of test . 43 5.3.9.1.1 Initial conditions . 43 5.3.9.1.2 Procedure . 43 5.3.9.2 Test requirements . 43 5.3.10 Out-of-synchronization handling of output power . 43 5.3.10.1 Method of test . 43 5.3.10.1.1 Initial conditions . 43 5.3.10.1.2 Procedure . 44 5.3.10.2 Test requirements . 44 5.3.11 Transmitter adjacent channel leakage power ratio . 44 5.3.11.1 Method of test . 44 5.3.11.1.1 UEs not supporting HSDPA and/or E-DCH . 44 5.3.11.1.1A UEs supporting HSDPA and/or E-DCH . 45 5.3.11.1.1B DC-HSUPA . 45 5.3.11.1.1C UL OLTD . 45 5.3.11.1.1D UL CLTD Activation state 1 . 46 5.3.11.2 Test requirements . 47 SIST EN 301 908-2 V7.1.1:2016
ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 6 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 48 Annex B (normative): Environmental profile . 50 B.1 General . 50 B.1.1 Introduction . 50 B.1.2 Temperature . 50 B.1.3 Voltage . 50 B.1.4 Test environment . 50 Annex C: Void . 51 Annex D (informative): Bibliography . 52 History . 53
ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 7 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document has been produced by ETSI in response to mandates M/284 and M/406 issued from the European Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.10]. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonised Standard under the Directive 1999/5/EC [i.2]. The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A. The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.11].
National transposition dates Date of adoption of this EN: 21 December 2015 Date of latest announcement of this EN (doa): 31 March 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 September 2016 Date of withdrawal of any conflicting National Standard (dow): 30 September 2017
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The modular structure is shown in ETSI EG 201 399 [i.3]. SIST EN 301 908-2 V7.1.1:2016
ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 8 1 Scope The present document applies to the following radio equipment type: • User Equipment for IMT-2000 CDMA Direct Spread (UTRA FDD). These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: UTRA FDD operating bands UTRA FDD Band Direction of transmission UTRA FDD operating bands I Transmit 1 920 MHz to 1 980 MHz Receive 2 110 MHz to 2 170 MHz III Transmit 1 710 MHz to 1 785 MHz Receive 1 805 MHz to 1 880 MHz VII Transmit 2 500 MHz to 2 570 MHz Receive 2 620 MHz to 2 690 MHz VIII Transmit 880 MHz to 915 MHz Receive 925 MHz to 960 MHz XV Transmit 1 900 MHz to 1 920 MHz Receive 2 600 MHz to 2 620 MHz XVI Transmit 2 010 MHz to 2 025 MHz Receive
2 585 MHz to 2 600 MHz XX Transmit 832 MHz to 862 MHz Receive 791 MHz to 821 MHz XXII Transmit 3 410 MHz to 3 490 MHz Receive 3 510 MHz to 3 590 MHz
The present document covers requirements for UTRA FDD User Equipment from 3GPP Releases 99, 4, 5, 6, 7, 8, 9, 10, and 11 defined in ETSI TS 125 101 [5]. This includes the requirements for UE operating bands from 3GPP Release 12 defined in ETSI TS 125 101 [i.12]. In addition, the present document covers requirements for UTRA FDD User Equipment in the operating bands specified in ETSI TS 102 735 [i.4]. NOTE 1: For Band XX: - for user equipment designed to be mobile or nomadic, the requirements in the present document measured at the antenna port also show conformity to the corresponding requirement defined as TRP (Total Radiated Power), as described in Commission Decision 2010/267/EU [i.7],
ECC Decision (09)03 [i.8] and CEPT Report 30 [i.9]; - for user equipment designed to be fixed or installed, the present document does not address the requirements described in Commission Decision 2010/267/EU [i.7], ECC Decision (09)03 [i.8] and CEPT Report 30 [i.9]. The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2, which states that "radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present document. NOTE 2: A list of such ENs is included on the web site http://www.newapproach.org/. SIST EN 301 908-2 V7.1.1:2016
ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 9 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] Void. [2] ETSI TS 134 121-1 (V12.1.0) (10-2015): "Universal Mobile Telecommunications System (UMTS); User Equipment (UE) conformance specification; Radio transmission and reception (FDD); Part 1: Conformance specification (3GPP TS 34.121-1 version 12.1.0 Release 12)". [3] ETSI TS 134 108 (V12.1.0) (10-2015): "Universal Mobile Telecommunications System (UMTS); LTE; Common test environments for User Equipment (UE); Conformance testing (3GPP TS 34.108 version 12.1.0 Release 12)". [4] ETSI TS 134 109 (V12.0.0) (09-2014): "Universal Mobile Telecommunications System (UMTS); Terminal logical test interface; Special conformance testing functions (3GPP TS 34.109 version 12.0.0 Release 12)". [5] ETSI TS 125 101 (V11.11.0) (01-2015): "Universal Mobile Telecommunications System (UMTS); User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.101 version 11.11.0 Release 11)". [6] IEC 60068-2-1 (03-2007): "Environmental testing - Part 2-1: Tests - Test A: Cold". [7] IEC 60068-2-2 (07-2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat". [8] ETSI TS 125 214 (V11.12.0) (07-2015): "Universal Mobile Telecommunications System (UMTS); Physical layer procedures (FDD) (3GPP TS 25.214 version 11.12.0 Release 11)". [9] ETSI TS 145 004 (V11.0.0) (10-2012): "Digital cellular telecommunications system (Phase 2+); Modulation (3GPP TS 45.004 version 11.0.0 Release 11)". 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations. [i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R&TTE Directive). SIST EN 301 908-2 V7.1.1:2016
ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 10 [i.3] ETSI EG 201 399 (V2.2.1) (08-2010): "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to the production of Harmonized Standards for application under the R&TTE Directive". [i.4] ETSI TS 102 735 (V7.1.0): "Universal Mobile Telecommunications System (UMTS); Band-specific requirements for UMTS Frequency Division Duplex (FDD) operation in the bands 1 900 MHz to 1 920 MHz paired with 2 600 MHz to 2 620 MHz and 2 010 MHz to 2 025 MHz paired with 2 585 MHz to 2 600 MHz". [i.5] Void. [i.6] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics". [i.7] Commission Decision 2010/267/EU of 6 May 2010 on harmonised technical conditions of use in the 790-862 MHz frequency band for terrestrial systems capable of providing electronic communications services in the European Union. [i.8] ECC Decision (09)03 of 30 October 2009 on harmonised conditions for mobile/fixed communications networks (MFCN) operating in the band 790 - 862 MHz. [i.9] CEPT Report 30 of 30 October 2009 to the European Commission in response to the Mandate on "The identification of common and minimal (least restrictive) technical conditions for 790 - 862 MHz for the digital dividend in the European Union". [i.10] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending Directive 98/34/EC laying down a procedure for the provision of information in the field of technical standards and regulations. [i.11] ETSI EN 301 908-1 (V7.1.1) (03-2015): "IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common requirements". [i.12] ETSI TS 125 101 (V12.9.0) (10-2015): "Universal Mobile Telecommunications System (UMTS); User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.101 version 12.9.0 Release 12)". 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: chip rate: rate of "chips" (modulated symbols after spreading) per second NOTE: The UTRA FDD chip rate is 3,84 Mchip/s. data rate: rate of the user information, which is transmitted over the Air Interface EXAMPLE: Output rate of the voice codec. enhanced performance receiver type 1 for DCH: receiver with performance requirements which are optional for the UE and utilize receiver diversity during DCH reception environmental profile: range of environmental conditions under which equipment within the scope of the present document is required to comply with the provisions of the present document maximum output power: measure of the maximum power the UE can transmit (i.e. the actual power as would be measured assuming no measurement error) in a bandwidth of at least (1 + α) times the chip rate of the radio access mode NOTE: The period of measurement is assumed to be at least one timeslot. SIST EN 301 908-2 V7.1.1:2016
ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 11 mean power: power (transmitted or received) in a bandwidth of at least (1 + α) times the chip rate of the radio access mode, when applied to a WCDMA modulated signal NOTE: The period of measurement is assumed to be at least one timeslot unless otherwise stated. node B: logical node responsible for radio transmission/reception in one or more cells to/from the User Equipment nominal maximum output power: nominal power defined by the UE power class operating band: frequency range that is defined with a specific set of technical requirements, in which UTRA FDD operates NOTE: Operating bands for UTRA are designated with Roman numerals, while the corresponding operating bands for E-UTRA are designated with Arabic numerals. power spectral density: function of power versus frequency and when integrated across a given bandwidth, the function represents the mean power in such a bandwidth NOTE 1: When the mean power is normalized to (divided by) the chip-rate it represents the mean energy per chip. Some signals are directly defined in terms of energy per chip, (DPCH_Ec, Ec, OCNS_Ec and S-CCPCH_Ec) and others defined in terms of PSD (Io, Ioc, Ior and Îor). There also exist qu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...