IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)

The present document covers requirements for UTRA FDD User Equipment from 3GPP Releases 99, 4, 5, 6, 7, 8, 9, 10,
and 11 defined in ETSI TS 125 101 [5]. This includes the requirements for UE operating bands from 3GPP Release 12
defined in ETSI TS 125 101 [i.12]. In addition, the present document covers requirements for UTRA FDD User
Equipment in the operating bands specified in ETSI TS 102 735 [i.4].
NOTE 1: For Band XX:
- for user equipment designed to be mobile or nomadic, the requirements in the present document
measured at the antenna port also show conformity to the corresponding requirement defined as
TRP (Total Radiated Power), as described in Commission Decision 2010/267/EU [i.7],
ECC Decision (09)03 [i.8] and CEPT Report 30 [i.9];
- for user equipment designed to be fixed or installed, the present document does not address the
requirements described in Commission Decision 2010/267/EU [i.7], ECC Decision (09)03 [i.8] and
CEPT Report 30 [i.9].
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2,
which states that "radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.

Celična omrežja IMT - Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE - 2. del: CDMA z neposrednim razprševanjem (“Direct Spread”) (UTRA FDD) (UE)

Ta dokument zajema zahteve za uporabniško opremo UTRA FDD iz izdaj 99, 4, 5, 6, 7, 8, 9, 10 in 11 dokumenta 3GPP, kot je določeno v dokumentu ETSI TS 125 101 [5]. To vključuje zahteve za pasove, v katerih deluje UE iz izdaje 12 dokumenta 3GPP, kot je določeno v dokumentu ETSI TS 125 101 [i.12]. Poleg tega ta dokument zajema zahteve za uporabniško opremo UTRA FDD, ki deluje v frekvenčnih pasovih, določenih v dokumentu ETSI TS 102 735 [i.4].
OPOMBA 1: Za pas XX:
- Za uporabniško opremo, zasnovano kot mobilno ali nomadsko, so zahteve iz tega dokumenta, izmerjene na antenskem vhodu, tudi v skladu z ustrezno zahtevo, opredeljeno kot TRP (skupna sevana moč), kot je opisana v Sklepu Komisije 2010/267/EU [i.7], Sklepu Odbora za elektronske komunikacije (09)03 [i.8] in poročilu CEPT 30 [i.9].
- Za uporabniško opremo, zasnovano za priključitev ali namestitev, ta dokument ne obravnava zahtev, opisanih v Sklepu Komisije 2010/267/EU [i.7], Sklepu Odbora za elektronske komunikacije (09)03 [i.8] in poročilu CEPT 30 [i.9].
Ta dokument zajema določbe člena 3.2 Direktive 1999/5/ES [i.2] (direktive R&TTE), ki navaja, da »/.../ mora biti radijska oprema skonstruirana tako, da učinkovito uporablja spekter, razporejen za prizemne/vesoljske radijske komunikacije in orbitalne vire, tako da ne pride do škodljivega motenja.«
Poleg tega dokumenta se lahko za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov člena 3 direktive R&TTE [i.2].

General Information

Status
Published
Publication Date
21-Jan-2016
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
12-Jan-2016
Due Date
18-Mar-2016
Completion Date
22-Jan-2016
Mandate

Buy Standard

Standard
EN 301 908-2 V7.1.1:2016
English language
53 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ETSI EN 301 908-2 V7.1.0 (2015-10) - IMT cellular networks; Harmonised EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)
English language
53 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 301 908-2 V7.0.1 (2015-05) - IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)
English language
55 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)33.070.99Druge mobilne storitveOther mobile services33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-2 V7.1.1SIST EN 301 908-2 V7.1.1:2016en01-marec-2016SIST EN 301 908-2 V7.1.1:2016SLOVENSKI
STANDARD



SIST EN 301 908-2 V7.1.1:2016



ETSI EN 301 908-2 V7.1.1 (2015-12) IMT cellular networks; Harmonised EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)
HARMONISED EUROPEAN STANDARD SIST EN 301 908-2 V7.1.1:2016



ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 2
Reference REN/MSG-TFES-011-02 Keywords 3G, 3GPP, cellular, digital, IMT, mobile, radio, regulation, UMTS, UTRA, WCDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-2 V7.1.1:2016



ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 Introduction . 7 1 Scope . 8 2 References . 9 2.1 Normative references . 9 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 10 3.1 Definitions . 10 3.2 Symbols . 11 3.3 Abbreviations . 12 4 Technical requirements specifications . 13 4.1 Environmental profile . 13 4.2 Conformance requirements . 13 4.2.1 Introduction. 13 4.2.2 Transmitter maximum output power. 14 4.2.2.1 Transmitter maximum output power . 14 4.2.2.1.1 Definition. 14 4.2.2.1.2 Limits . 14 4.2.2.1.3 Conformance . 14 4.2.2.2 Transmitter maximum output power for DC-HSUPA . 14 4.2.2.2.1 Definition for DC-HSUPA . 14 4.2.2.2.2 Limits for DC-HSUPA . 15 4.2.2.2.3 Conformance . 15 4.2.2.3 Transmitter maximum output power for UL OLTD . 15 4.2.2.3.1 Definition for UL OLTD . 15 4.2.2.3.2 Limits for UL OLTD . 15 4.2.2.3.3 Conformance . 15 4.2.3 Transmitter spectrum emission mask . 16 4.2.3.1 Transmitter spectrum emission mask . 16 4.2.3.1.1 Definition. 16 4.2.3.1.2 Limits . 16 4.2.3.1.3 Conformance . 16 4.2.3.2 Transmitter spectrum emission mask for DC-HSUPA . 16 4.2.3.2.1 Definition for DC-HSUPA . 16 4.2.3.2.2 Limits for DC-HSUPA . 16 4.2.3.2.3 Conformance . 17 4.2.3.3 Transmitter spectrum emission mask for UL OLTD . 17 4.2.3.3.1 Definition for UL OLTD . 17 4.2.3.3.2 Limits for UL OLTD . 17 4.2.3.3.3 Conformance . 17 4.2.3.4 Transmitter spectrum emission mask for UL CLTD Activation state 1 . 18 4.2.3.4.1 Definition for UL CLTD Activation state 1 . 18 4.2.3.4.2 Limits for UL CLTD Activation state 1 . 18 4.2.3.4.3 Conformance . 18 4.2.4 Transmitter spurious emissions . 18 4.2.4.1 Transmitter spurious emissions . 18 4.2.4.1.1 Definition. 18 4.2.4.1.2 Limits . 18 4.2.4.1.3 Conformance . 20 4.2.4.2 Transmitter spurious emissions for DC-HSUPA . 20 4.2.4.2.1 Definition for DC-HSUPA . 20 4.2.4.2.2 Limits for DC-HSUPA . 20 SIST EN 301 908-2 V7.1.1:2016



ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 4 4.2.4.2.3 Conformance . 22 4.2.5 Transmitter minimum output power . 23 4.2.5.1 Transmitter minimum output power. 23 4.2.5.1.1 Definition. 23 4.2.5.1.2 Limits . 23 4.2.5.1.3 Conformance . 23 4.2.5.2 Transmitter minimum output power for DC-HSUPA . 23 4.2.5.2.1 Definition for DC-HSUPA . 23 4.2.5.2.2 Limits for DC-HSUPA . 23 4.2.5.2.3 Conformance . 23 4.2.5.3 Transmitter minimum output power for UL CLTD Activation state 1 . 23 4.2.5.3.1 Definition for UL CLTD Activation state 1 . 23 4.2.5.3.2 Limits for UL CLTD Activation state 1 . 23 4.2.5.3.3 Conformance . 23 4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 23 4.2.6.1 Definition . 23 4.2.6.2 Limits . 24 4.2.6.3 Conformance . 24 4.2.7 Receiver blocking characteristics . 24 4.2.7.1 Definition . 24 4.2.7.2 Limits . 24 4.2.7.3 Conformance . 26 4.2.8 Receiver spurious response . 26 4.2.8.1 Definition . 26 4.2.8.2 Limits . 26 4.2.8.3 Conformance . 26 4.2.9 Receiver intermodulation characteristics . 26 4.2.9.1 Definition . 26 4.2.9.2 Limits . 26 4.2.9.3 Conformance . 27 4.2.10 Receiver spurious emissions . 27 4.2.10.1 Definition . 27 4.2.10.2 Limits . 27 4.2.10.3 Conformance . 28 4.2.11 Out-of-synchronization handling of output power . 28 4.2.11.1 Definition . 28 4.2.11.2 Limits . 28 4.2.11.3 Conformance . 30 4.2.12 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 30 4.2.12.1 Transmitter adjacent channel leakage power ratio (ACLR) . 30 4.2.12.1.1 Definition. 30 4.2.12.1.2 Limits . 30 4.2.12.1.3 Conformance . 30 4.2.12.2 Adjacent channel leakage power ratio for DC-HSUPA . 30 4.2.12.2.1 Definition for DC-HSUPA . 30 4.2.12.2.2 Limits for DC-HSUPA . 30 4.2.12.2.3 Conformance . 30 4.2.12.3 Adjacent channel leakage power ratio for UL OLTD . 31 4.2.12.3.1 Definition for UL OLTD . 31 4.2.12.3.2 Limits for UL OLTD . 31 4.2.12.3.3 Conformance . 31 4.2.12.4 Adjacent channel leakage power ratio for UL CLTD Activation state 1 . 31 4.2.12.4.1 Definition for UL CLTD Activation state 1 . 31 4.2.12.4.2 Limits for UL CLTD Activation state 1 . 31 4.2.12.4.3 Conformance . 31 5 Testing for compliance with technical requirements . 32 5.1 Environmental conditions for testing . 32 5.2 Interpretation of the measurement results . 32 5.3 Essential radio test suites . 33 5.3.1 Transmitter maximum output power. 33 5.3.1.1 Method of test . 33 SIST EN 301 908-2 V7.1.1:2016



ETSI ETSI EN 301 908-2 V7.1.1 (2015-12) 5 5.3.1.1.1 UTRA . 33 5.3.1.1.1A DC-HSUPA . 34 5.3.1.1.1B UL OLTD . 34 5.3.1.2 Test requirements . 35 5.3.2 Transmitter spectrum emission mask . 35 5.3.2.1 Method of test . 35 5.3.2.1.1 UEs not supporting HSDPA and/or E-DCH . 35 5.3.2.1.1A UEs supporting HSDPA and/or E-DCH . 36 5.3.2.1.1B DC-HSUPA . 36 5.3.2.1.1C UL OLTD . 36 5.3.2.1.1D UL CLTD Activation state 1 . 37 5.3.2.2 Test requirements . 38 5.3.3 Transmitter spurious emissions . 38 5.3.3.1 Method of test . 38 5.3.3.1.1 UTRA . 38 5.3.3.1.1A DC-HSUPA . 38 5.3.3.2 Test requirements . 39 5.3.4 Transmitter minimum output power . 39 5.3.4.1 Method of test . 39 5.3.4.1.1 UTRA . 39 5.3.4.1.1A DC-HSUPA . 39 5.3.4.1.1B UL CLTD Activation state 1 . 40 5.3.4.2 Test requirements . 40 5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 40 5.3.5.1 Method of test . 40 5.3.5.1.1 Initial conditions . 40 5.3.5.1.2 Procedure . 41 5.3.5.2 Test requirements . 41 5.3.6 Receiver blocking characteristics . 41 5.3.6.1 Method of test . 41 5.3.6.1.1 Initial requirements . 41 5.3.6.1.2 Procedure . 41 5.3.6.2 Test requirements . 41 5.3.7 Receiver spurious response . 42 5.3.7.1 Method of test . 42 5.3.7.1.1 Initial conditions . 42 5.3.7.1.2 Procedure . 42 5.3.7.2 Test requirements . 42 5.3.8 Receiver Intermodulation characteristics . 42 5.3.8.1 Method of test . 42 5.3.8.1.1 Initial conditions . 42 5.3.8.1.2 Procedure . 43 5.3.8.2 Test requirements . 43 5.3.9 Receiver spurious emissions . 43 5.3.9.1 Method of test . 43 5.3.9.1.1 Initial conditions . 43 5.3.9.1.2 Procedure . 43 5.3.9.2 Test requirements . 43 5.3.10 Out-of-synchronization handling of output power . 43 5.3.10.1 Method of test . 43 5.3.10.1.1 Initial conditions . 43 5.3.10.1.2 Procedure . 44 5.3.10.2 Test requirements . 44 5.3.11 Transmitter adjacent channel leakage power ratio . 44 5.3.11.1 Method of test . 44 5.3.11.1.1 UEs not supporting HSDPA and/or E-DCH . 44 5.3.11.1.1A UEs supporting HSDPA and/or E-DCH . 45 5.3.11.1.1B DC-HSUPA .
...

Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)






HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised EN covering the essential requirements
of article 3.2 of the R&TTE Directive;
Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)



Reference
REN/MSG-TFES-011-02
Keywords
3G, 3GPP, cellular, digital, IMT, mobile, radio,
regulation, UMTS, UTRA, WCDMA

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2015.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 11
3.3 Abbreviations . 12
4 Technical requirements specifications . 13
4.1 Environmental profile . 13
4.2 Conformance requirements . 13
4.2.1 Introduction. 13
4.2.2 Transmitter maximum output power. 14
4.2.2.1 Transmitter maximum output power . 14
4.2.2.1.1 Definition. 14
4.2.2.1.2 Limits . 14
4.2.2.1.3 Conformance . 14
4.2.2.2 Transmitter maximum output power for DC-HSUPA . 14
4.2.2.2.1 Definition for DC-HSUPA . 14
4.2.2.2.2 Limits for DC-HSUPA . 15
4.2.2.2.3 Conformance . 15
4.2.2.3 Transmitter maximum output power for UL OLTD . 15
4.2.2.3.1 Definition for UL OLTD . 15
4.2.2.3.2 Limits for UL OLTD . 15
4.2.2.3.3 Conformance . 15
4.2.3 Transmitter spectrum emission mask . 16
4.2.3.1 Transmitter spectrum emission mask . 16
4.2.3.1.1 Definition. 16
4.2.3.1.2 Limits . 16
4.2.3.1.3 Conformance . 16
4.2.3.2 Transmitter spectrum emission mask for DC-HSUPA . 16
4.2.3.2.1 Definition for DC-HSUPA . 16
4.2.3.2.2 Limits for DC-HSUPA . 16
4.2.3.2.3 Conformance . 17
4.2.3.3 Transmitter spectrum emission mask for UL OLTD . 17
4.2.3.3.1 Definition for UL OLTD . 17
4.2.3.3.2 Limits for UL OLTD . 17
4.2.3.3.3 Conformance . 17
4.2.3.4 Transmitter spectrum emission mask for UL CLTD Activation state 1 . 18
4.2.3.4.1 Definition for UL CLTD Activation state 1 . 18
4.2.3.4.2 Limits for UL CLTD Activation state 1 . 18
4.2.3.4.3 Conformance . 18
4.2.4 Transmitter spurious emis sions . 18
4.2.4.1 Transmitter spurious emissions . 18
4.2.4.1.1 Definition. 18
4.2.4.1.2 Limits . 18
4.2.4.1.3 Conformance . 20
4.2.4.2 Transmitter spurious emissions for DC-HSUPA . 20
4.2.4.2.1 Definition for DC-HSUPA . 20
4.2.4.2.2 Limits for DC-HSUPA . 20
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)
4.2.4.2.3 Conformance . 22
4.2.5 Transmitter minimum output power . 23
4.2.5.1 Transmitter minimum output power. 23
4.2.5.1.1 Definition. 23
4.2.5.1.2 Limits . 23
4.2.5.1.3 Conformance . 23
4.2.5.2 Transmitter minimum output power for DC-HSUPA . 23
4.2.5.2.1 Definition for DC-HSUPA . 23
4.2.5.2.2 Limits for DC-HSUPA . 23
4.2.5.2.3 Conformance . 23
4.2.5.3 Transmitter minimum output power for UL CLTD Activation state 1 . 23
4.2.5.3.1 Definition for UL CLTD Activation state 1 . 23
4.2.5.3.2 Limits for UL CLTD Activation state 1 . 23
4.2.5.3.3 Conformance . 23
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 23
4.2.6.1 Definition . 23
4.2.6.2 Limits . 24
4.2.6.3 Conformance . 24
4.2.7 Receiver blocking characteristics . 24
4.2.7.1 Definition . 24
4.2.7.2 Limits . 24
4.2.7.3 Conformance . 26
4.2.8 Receiver spurious response . 26
4.2.8.1 Definition . 26
4.2.8.2 Limits . 26
4.2.8.3 Conformance . 26
4.2.9 Receiver intermodulation characteristics . 26
4.2.9.1 Definition . 26
4.2.9.2 Limits . 26
4.2.9.3 Conformance . 27
4.2.10 Receiver spurious emissions . 27
4.2.10.1 Definition . 27
4.2.10.2 Limits . 27
4.2.10.3 Conformance . 28
4.2.11 Out-of-synchronization handling of output power . 28
4.2.11.1 Definition . 28
4.2.11.2 Limits . 28
4.2.11.3 Conformance . 30
4.2.12 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 30
4.2.12.1 Transmitter adjacent channel leakage power ratio (ACLR) . 30
4.2.12.1.1 Definition. 30
4.2.12.1.2 Limits . 30
4.2.12.1.3 Conformance . 30
4.2.12.2 Adjacent channel leakage power ratio for DC-HSUPA . 30
4.2.12.2.1 Definition for DC-HSUPA . 30
4.2.12.2.2 Limits for DC-HSUPA . 30
4.2.12.2.3 Conformance . 30
4.2.12.3 Adjacent channel leakage power ratio for UL OLTD . 31
4.2.12.3.1 Definition for UL OLTD . 31
4.2.12.3.2 Limits for UL OLTD . 31
4.2.12.3.3 Conformance . 31
4.2.12.4 Adjacent channel leakage power ratio for UL CLTD Activation state 1 . 31
4.2.12.4.1 Definition for UL CLTD Activation state 1 . 31
4.2.12.4.2 Limits for UL CLTD Activation state 1 . 31
4.2.12.4.3 Conformance . 31
5 Testing for compliance with technical requirements . 32
5.1 Environmental conditions for testing . 32
5.2 Interpretation of the measurement results . 32
5.3 Essential radio test suites . 33
5.3.1 Transmitter maximum output power. 33
5.3.1.1 Method of test . 33
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 908-2 V7.1.0 (2015-10)
5.3.1.1.1 UTRA . 33
5.3.1.1.1A DC-HSUPA . 34
5.3.1.1.1B UL OLTD . 34
5.3.1.2 Test requirements . 35
5.3.2 Transmitter spectrum emission mask . 35
5.3.2.1 Method of test . 35
5.3.2.1.1 UEs not supporting HSDPA and/or E-DCH . 35
5.3.2.1.1A UEs supporting HSDPA and/or E-DCH . 36
5.3.2.1.1B DC-HSUPA . 36
5.3.2.1.1C UL OLTD . 36
5.3.2.1.1D UL CLTD Activation state 1 . 37
5.3.2.2 Test requirements . 38
5.3.3 Transmitter spurious emis sions . 38
5.3.3.1 Method of test . 38
5.3.3.1.1 UTRA . 38
5.3.3.1.1A DC-HSUPA . 38
5.3.3.2 Test requirements . 39
5.3.4 Transmitter minimum output power . 39
5.3.4.1 Method of test . 39
5.3.4.1.1 UTRA . 39
5.3.4.1.1A DC-HSUPA . 39
5.3.4.1.1B UL CLTD Activation state 1 . 40
5.3.4.2 Test requirements . 40
5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 40
5.3.5.1 Method of test . 40
5.3.5.1.1 Initial conditions . 40
5.3.5.1.2 Procedure . 41
5.3.5.2 Test requirements . 41
5.3.6 Receiver blocking characteristics . 41
5.3.6.1 Method of test . 41
5.3.6.1.1 Initial requirements . 41
5.3.6.1.2 Procedure . 41
5.3.6.2 Test requirements . 41
5.3.7 Receiver spurious response . 42
5.3.7.1 Method of test . 42
5.3.7.1.1 Initial conditions . 42
5.3.7.1.2 Procedure . 42
5.3.7.2 Test requirements . 42
5.3.8 Receiver Intermodulation characteristics . 42
5.3.8.1 Method of test . 42
5.3.8.1.1 Initial conditions . 42
5.3.8.1.2 Procedure . 43
5.3.8.2 Test requirements . 43
5.3.9 Receiver spurious emissions . 43
5.3.9.1 Method of test . 43
5.3.9.1.1 Initial conditions . 43
5.3.9.1.2 Procedure . 43
5.3.9.2 Test requirements . 43
5.3.10 Out-of-synchronization handling of output power . 43
5.3.10.1 Method of test . 43
5.3.10.1.1 Initial conditions . 43
5.3.10.1.2 Procedure . 44
5.3.10.2 Test requirements . 44
5.3.11 Transmitter adjacent channel leakage power ratio . 44
5.3.11.1 Method of test . 44
5.3.11.1.1 UEs not supporting HSDPA and/or E-DCH . 44
5.3.11.1.1A UEs supporting HSDPA and/or E-DCH . 45
5.3.11.1.1B DC-HSUPA . 45
5.3.11.1.1C UL OLTD .
...

Draft ETSI EN 301 908-2 V7.0.1 (2015-05)






HARMONIZED EUROPEAN STANDARD
IMT cellular networks;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive;
Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 908-2 V7.0.1 (2015-05)



ReRefeferreencncee
RREENN//MMSSGG--TTFES-011-02FES-011-02
KKeeyywwords ords
3G3G, 3G, 3GPP, cePP, cellullular, dlar, diigigital,tal, IM IMTT,, mobil mobilee, rad, radiio, o,
regularegulattioion, Un, UMMTTSS, U, UTTRRAA, , WWCCDDMMAA



ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2015.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 908-2 V7.0.1 (2015-05)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 11
3.3 Abbreviations . 12
4 Technical requirements specifications . 13
4.1 Environmental profile . 13
4.2 Conformance requirements . 13
4.2.1 Introduction. 13
4.2.2 Transmitter maximum output power. 14
4.2.2.1 Transmitter maximum output power . 14
4.2.2.1.1 Definition. 14
4.2.2.1.2 Limits . 14
4.2.2.1.3 Conformance . 14
4.2.2.2 Transmitter maximum output power for DC-HSUPA . 15
4.2.2.2.1 Definition for DC-HSUPA . 15
4.2.2.2.2 Limits for DC-HSUPA . 15
4.2.2.2.3 Conformance . 15
4.2.2.3 Transmitter maximum output power for UL OLTD . 15
4.2.2.3.1 Definition for UL OLTD . 15
4.2.2.3.2 Limits for UL OLTD . 15
4.2.2.3.3 Conformance . 16
4.2.3 Transmitter spectrum emission mask . 16
4.2.3.1 Transmitter spectrum emission mask . 16
4.2.3.1.1 Definition. 16
4.2.3.1.2 Limits . 16
4.2.3.1.3 Conformance . 16
4.2.3.2 Transmitter spectrum emission mask for DC-HSUPA . 17
4.2.3.2.1 Definition for DC-HSUPA . 17
4.2.3.2.2 Limits for DC-HSUPA . 17
4.2.3.2.3 Conformance . 17
4.2.3.3 Transmitter spectrum emission mask for UL OLTD . 17
4.2.3.3.1 Definition for UL OLTD . 17
4.2.3.3.2 Limits for UL OLTD . 17
4.2.3.3.3 Conformance . 18
4.2.3.4 Transmitter spectrum emission mask for UL CLTD Activation state 1 . 18
4.2.3.4.1 Definition for UL CLTD Activation state 1 . 18
4.2.3.4.2 Limits for UL CLTD Activation state 1 . 18
4.2.3.4.3 Conformance . 19
4.2.4 Transmitter spurious emis sions . 19
4.2.4.1 Transmitter spurious emissions . 19
4.2.4.1.1 Definition. 19
4.2.4.1.2 Limits . 19
4.2.4.1.3 Conformance . 21
4.2.4.2 Transmitter spurious emissions for DC-HSUPA . 21
4.2.4.2.1 Definition for DC-HSUPA . 21
4.2.4.2.2 Limits for DC-HSUPA . 21
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 908-2 V7.0.1 (2015-05)
4.2.4.2.3 Conformance . 23
4.2.5 Transmitter minimum output power . 24
4.2.5.1 Transmitter minimum output power. 24
4.2.5.1.1 Definition. 24
4.2.5.1.2 Limits . 24
4.2.5.1.3 Conformance . 24
4.2.5.2 Transmitter minimum output power for DC-HSUPA . 24
4.2.5.2.1 Definition for DC-HSUPA . 24
4.2.5.2.2 Limits for DC-HSUPA . 24
4.2.5.2.3 Conformance . 24
4.2.5.3 Transmitter minimum output power for UL CLTD Activation state 1 . 24
4.2.5.3.1 Definition for UL CLTD Activation state 1 . 24
4.2.5.3.2 Limits for UL CLTD Activation state 1 . 24
4.2.5.3.3 Conformance . 24
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 24
4.2.6.1 Definition . 24
4.2.6.2 Limits . 25
4.2.6.3 Conformance . 25
4.2.7 Receiver blocking characteristics . 25
4.2.7.1 Definition . 25
4.2.7.2 Limits . 25
4.2.7.3 Conformance . 27
4.2.8 Receiver spurious response . 27
4.2.8.1 Definition . 27
4.2.8.2 Limits . 27
4.2.8.3 Conformance . 27
4.2.9 Receiver intermodulation characteristics . 27
4.2.9.1 Definition . 27
4.2.9.2 Limits . 27
4.2.9.3 Conformance . 28
4.2.10 Receiver spurious emissions . 28
4.2.10.1 Definition . 28
4.2.10.2 Limits . 28
4.2.10.3 Conformance . 30
4.2.11 Out-of-synchronization handling of output power . 30
4.2.11.1 Definition . 30
4.2.11.2 Limits . 30
4.2.11.3 Conformance . 32
4.2.12 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 32
4.2.12.1 Transmitter adjacent channel leakage power ratio (ACLR) . 32
4.2.12.1.1 Definition. 32
4.2.12.1.2 Limits . 32
4.2.12.1.3 Conformance . 32
4.2.12.2 Adjacent channel leakage power ratio for DC-HSUPA . 32
4.2.12.2.1 Definition for DC-HSUPA . 32
4.2.12.2.2 Limits for DC-HSUPA . 32
4.2.12.2.3 Conformance . 32
4.2.12.3 Adjacent channel leakage power ratio for UL OLTD . 33
4.2.12.3.1 Definition for UL OLTD . 33
4.2.12.3.2 Limits for UL OLTD . 33
4.2.12.3.3 Conformance . 33
4.2.12.4 Adjacent channel leakage power ratio for UL CLTD Activation state 1 . 33
4.2.12.4.1 Definition for UL CLTD Activation state 1 . 33
4.2.12.4.2 Limits for UL CLTD Activation state 1 . 33
4.2.12.4.3 Conformance . 33
5 Testing for compliance with technical requirements . 34
5.1 Environmental conditions for testing . 34
5.2 Interpretation of the measurement results . 34
5.3 Essential radio test suites . 35
5.3.1 Transmitter maximum output power. 35
5.3.1.1 Method of test . 35
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 908-2 V7.0.1 (2015-05)
5.3.1.1.1 UTRA . 35
5.3.1.1.1A DC-HSUPA . 36
5.3.1.1.1B UL OLTD . 36
5.3.1.2 Test requirements . 37
5.3.2 Transmitter spectrum emission mask . 37
5.3.2.1 Method of test . 37
5.3.2.1.1 UEs not supporting HSDPA and/or E-DCH . 37
5.3.2.1.1A UEs supporting HSDPA and/or E-DCH . 38
5.3.2.1.1B DC-HSUPA . 38
5.3.2.1.1C UL OLTD . 39
5.3.2.1.1D UL CLTD Activation state 1 . 39
5.3.2.2 Test requirements . 40
5.3.3 Transmitter spurious emis sions . 40
5.3.3.1 Method of test . 40
5.3.3.1.1 UTRA . 40
5.3.3.1.1A DC-HSUPA . 41
5.3.3.2 Test requirements . 41
5.3.4 Transmitter minimum output power . 41
5.3.4.1 Method of test . 41
5.3.4.1.1 UTRA . 41
5.3.4.1.1A DC-HSUPA . 42
5.3.4.1.1B UL CLTD Activation state 1 . 42
5.3.4.2 Test requirements . 42
5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 43
5.3.5.1 Method of test . 43
5.3.5.1.1 Initial conditions . 43
5.3.5.1.2 Procedure . 43
5.3.5.2 Test requirements . 43
5.3.6 Receiver blocking characteristics . 43
5.3.6.1 Method of test . 43
5.3.6.1.1 Initial requirements . 43
5.3.6.1.2 Procedure . 44
5.3.6.2 Test requirements . 44
5.3.7 Receiver spurious response . 44
5.3.7.1 Method of test . 44
5.3.7.1.1 Initial conditions . 44
5.3.7.1.2 Procedure . 44
5.3.7.2 Test requirements . 44
5.3.8 Receiver Intermodulation characteristics . 45
5.3.8.1 Method of test . 45
5.3.8.1.1 Initial conditions . 45
5.3.8.1.2 Procedure . 45
5.3.8.2 Test requirements . 45
5.3.9 Receiver spurious emissions . 45
5.3.9.1 Method of test . 45
5.3.9.1.1 Initial conditions . 45
5.3.9.1.2 Procedure . 45
5.3.9.2 Test requirements . 45
5.3.10 Out-of-synchronization handling of output power . 46
5.3.10.1 Method of test . 46
5.3.10.1.1 Initial conditions . 46
5.3.10.1.2 Procedure . 46
5.3.10.2 Test requirements . 46
5.3.11 Transmitter adjacent channel leakage power ratio . 46
5.3.11.1 Method of test . 46
5.3.11.1.1 UEs not supporting HSDPA and/or E-DCH . 46
5.3.11.1.1A UEs supporting HSDPA and/or E-DCH . 47
5.3.11.1.1B DC-HSUPA . 47
5.3.11.1.1C UL OLTD .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.