ETSI EN 303 699 V1.1.1 (2021-02)
Satellite Earth Stations and Systems (SES); Fixed earth stations communicating with non-geostationary satellite systems in the 20 GHz and 30 GHz FSS bands; Harmonised Standard for access to radio spectrum
Satellite Earth Stations and Systems (SES); Fixed earth stations communicating with non-geostationary satellite systems in the 20 GHz and 30 GHz FSS bands; Harmonised Standard for access to radio spectrum
DEN/SES-00444
Satelitske zemeljske postaje in sistemi (SES) - Fiksne zemeljske postaje, ki komunicirajo z negeostacionarnimi satelitskimi sistemi FSS v pasovih 20 GHz in 30 GHz - Harmonizirani standard za dostop do radijskega spektra
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 303 699 V1.1.1:2021
01-april-2021
Satelitske zemeljske postaje in sistemi (SES) - Fiksne zemeljske postaje, ki
komunicirajo z negeostacionarnimi satelitskimi sistemi FSS v pasovih 20 GHz in
30 GHz - Harmonizirani standard za dostop do radijskega spektra
Satellite Earth Stations and Systems (SES) - Fixed earth stations communicating with
non-geostationary satellite systems in the 20 GHz and 30 GHz FSS bands - Harmonised
Standard for access to radio spectrum
Ta slovenski standard je istoveten z: ETSI EN 303 699 V1.1.1 (2021-02)
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
SIST EN 303 699 V1.1.1:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 303 699 V1.1.1:2021
---------------------- Page: 2 ----------------------
SIST EN 303 699 V1.1.1:2021
ETSI EN 303 699 V1.1.1 (2021-02)
HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Fixed earth stations communicating with non-geostationary
satellite systems in the 20 GHz and 30 GHz FSS bands;
Harmonised Standard for access to radio spectrum
---------------------- Page: 3 ----------------------
SIST EN 303 699 V1.1.1:2021
2 ETSI EN 303 699 V1.1.1 (2021-02)
Reference
DEN/SES-00444
Keywords
antenna, earth station, FSS, harmonised
standard, non-GSO, regulation, satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 303 699 V1.1.1:2021
3 ETSI EN 303 699 V1.1.1 (2021-02)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms . 11
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General . 14
4.1.1 Environmental profile . 14
4.1.2 Operational configurations . 14
4.1.3 EIRP for networks of ESs . 14
Aggregate
4.1.4 Presentation of equipment for testing purposes . 15
4.1.5 Choice of model for testing . 15
4.1.6 Void . 15
4.1.7 Peak pointing accuracy . 15
4.2 Conformance requirements . 15
4.2.1 Off-axis spurious radiation . 15
4.2.1.1 Justification . 15
4.2.1.2 Specification. 15
4.2.1.3 Conformance tests . 16
4.2.2 On-axis spurious radiation . 16
4.2.2.1 Justification . 16
4.2.2.2 Specification. 17
4.2.2.2.1 "Carrier-on" radio state . 17
4.2.2.2.2 "Carrier-off" and "Emissions disabled" radio states . 17
4.2.2.3 Conformance tests . 17
4.2.3 Void . 17
4.2.4 Void . 17
4.2.5 Carrier suppression . 17
4.2.5.1 Justification . 17
4.2.5.2 Specification. 18
4.2.5.3 Conformance tests . 18
4.2.6 Antenna pointing accuracy . 18
4.2.6.1 Purpose . 18
4.2.6.2 Pointing accuracy specification . 18
4.2.6.3 On-axis cross polarization isolation specification . 18
4.2.6.4 Conformance tests . 18
4.2.7 Cessation of emissions . 18
4.2.7.1 Justification . 18
4.2.7.2 Specification. 18
4.2.7.2.1 Specification 1: Mode of cessation of emissions . 18
4.2.7.2.2 Specification 2: Conditions under which the ES shall cease emissions. 19
4.2.7.2.3 Specification 3: Cessation of emissions . 19
4.2.7.2.4 Specification 4: Fault conditions . 19
4.2.7.3 Conformance tests . 20
4.2.8 Control and Monitoring Functions (CMFs) . 20
4.2.8.1 ES States . 20
4.2.8.1.1 General . 20
ETSI
---------------------- Page: 5 ----------------------
SIST EN 303 699 V1.1.1:2021
4 ETSI EN 303 699 V1.1.1 (2021-02)
4.2.8.1.2 CMF state diagram . 21
4.2.8.2 Processor monitoring . 22
4.2.8.2.1 Justification . 22
4.2.8.2.2 Specification . 22
4.2.8.2.3 Conformance tests . 22
4.2.8.3 Transmit subsystem monitoring . 23
4.2.8.3.1 Justification . 23
4.2.8.3.2 Specification . 23
4.2.8.3.3 Conformance tests . 23
4.2.8.4 Power-on/Reset . 23
4.2.8.4.1 Justification . 23
4.2.8.4.2 Specification . 23
4.2.8.4.3 Conformance tests . 23
4.2.8.5 Control Channel (CC) and Response Channel (RC) . 23
4.2.8.5.1 Justification . 23
4.2.8.5.2 Specification . 23
4.2.8.5.3 Conformance tests . 24
4.2.8.6 Network control commands . 24
4.2.8.6.1 Justification . 24
4.2.8.6.2 Specification . 24
4.2.8.6.3 Conformance tests . 25
4.2.8.7 Initial burst transmission . 25
4.2.8.7.1 Justification . 25
4.2.8.7.2 Specification . 25
4.2.8.7.3 Conformance tests . 25
4.2.8.8 Inhibition of transmissions . 25
4.2.8.8.1 Justification . 25
4.2.8.8.2 Specification . 25
4.2.8.8.3 Conformance tests . 26
4.2.9 Receive antenna off-axis gain pattern . 26
4.2.9.1 Justification . 26
4.2.9.2 Specification. 26
4.2.9.3 Conformance tests . 26
4.2.10 Blocking performance . 26
4.2.10.1 Justification . 26
4.2.10.2 Specification. 27
4.2.10.3 Conformance tests . 27
4.2.11 Adjacent Signal Selectivity . 27
4.2.11.1 Justification . 27
4.2.11.2 Specification. 27
4.2.11.3 Conformance tests . 27
4.2.12 Image frequency rejection . 28
4.2.12.1 Justification . 28
4.2.12.2 Specification. 28
4.2.12.3 Conformance tests . 28
5 Testing for compliance with technical requirements . 28
5.1 Environmental conditions for testing . 28
5.2 Ancillary Equipment . 28
5.3 Nominated Bandwidth . 28
5.4 Interpretation of the measurement results . 29
6 Test methods for all aspects of the ES. 29
6.1 General . 29
6.1.1 General requirements . 29
6.1.2 Special considerations for the interpretation of measurement results . 29
6.1.3 Measuring receiver . 30
6.2 Off-axis spurious radiation . 31
6.2.1 General . 31
6.2.2 Test method . 31
6.2.2.1 General . 31
6.2.2.2 Multi-carrier operation . 31
ETSI
---------------------- Page: 6 ----------------------
SIST EN 303 699 V1.1.1:2021
5 ETSI EN 303 699 V1.1.1 (2021-02)
6.2.3 Measurements up to 1 000 MHz . 32
6.2.3.1 Test site . 32
6.2.3.2 Measuring receivers . 32
6.2.3.3 Procedure . 32
6.2.4 Measurements above 1 000 MHz . 32
6.2.4.1 General . 32
6.2.4.2 Identification of the significant frequencies of spurious radiation . 33
6.2.4.2.1 Test site. 33
6.2.4.2.2 Procedure . 33
6.2.4.3 Measurement of radiated power levels of identified spurious radiation . 33
6.2.4.3.1 Test site. 33
6.2.4.3.2 Procedure . 34
6.2.4.4 Measurement of conducted spurious radiation at the antenna flange . 35
6.2.4.4.1 Test site. 35
6.2.4.4.2 Procedure . 35
6.3 On-axis spurious radiation . 36
6.3.1 Test method . 36
6.3.1.1 General . 36
6.3.1.2 Test site . 36
6.3.1.3 Method of measurement . 36
6.3.1.3.1 General . 36
6.3.1.3.2 Method of measurement at the antenna flange . 36
6.3.1.3.3 Method of measurement for an EUT with antenna . 38
6.4 Void . 39
6.5 Carrier suppression . 39
6.5.1 General . 39
6.5.2 Test method . 39
6.6 Antenna pointing . 40
6.6.1 General . 40
6.6.2 Test method . 40
6.7 Polarization angle alignment capability . 41
6.7.1 General . 41
6.7.2 Test site . 41
6.7.3 Procedure . 41
6.8 Cessation of emissions of the ES . 42
6.8.1 General . 42
6.8.2 Test Method . 42
6.8.2.1 Required documentation . 42
6.8.2.2 Cessation of emissions from the "Transmission enabled" state . 42
6.8.2.3 Cessation of emission from the "Transmission disabled" state . 42
6.8.2.4 Cessation of emission from the "Initial Phase" state . 43
6.8.2.4.1 EUTs transmitting initial bursts . 43
6.8.2.4.2 EUTs not transmitting initial bursts . 43
6.8.2.5 "Single action" means of cessation of emissions. 43
6.8.2.6 Fault conditions . 44
6.9 Control and monitoring functions . 44
6.9.1 General . 44
6.9.2 Test arrangement . 45
6.9.3 Processor monitoring- Test method . 45
...
ETSI EN 303 699 V1.1.1 (2021-02)
HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Fixed earth stations communicating with non-geostationary
satellite systems in the 20 GHz and 30 GHz FSS bands;
Harmonised Standard for access to radio spectrum
---------------------- Page: 1 ----------------------
2 ETSI EN 303 699 V1.1.1 (2021-02)
Reference
DEN/SES-00444
Keywords
antenna, earth station, FSS, harmonised
standard, non-GSO, regulation, satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 303 699 V1.1.1 (2021-02)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms . 11
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General . 14
4.1.1 Environmental profile . 14
4.1.2 Operational configurations . 14
4.1.3 EIRP for networks of ESs . 14
Aggregate
4.1.4 Presentation of equipment for testing purposes . 15
4.1.5 Choice of model for testing . 15
4.1.6 Void . 15
4.1.7 Peak pointing accuracy . 15
4.2 Conformance requirements . 15
4.2.1 Off-axis spurious radiation . 15
4.2.1.1 Justification . 15
4.2.1.2 Specification. 15
4.2.1.3 Conformance tests . 16
4.2.2 On-axis spurious radiation . 16
4.2.2.1 Justification . 16
4.2.2.2 Specification. 17
4.2.2.2.1 "Carrier-on" radio state . 17
4.2.2.2.2 "Carrier-off" and "Emissions disabled" radio states . 17
4.2.2.3 Conformance tests . 17
4.2.3 Void . 17
4.2.4 Void . 17
4.2.5 Carrier suppression . 17
4.2.5.1 Justification . 17
4.2.5.2 Specification. 18
4.2.5.3 Conformance tests . 18
4.2.6 Antenna pointing accuracy . 18
4.2.6.1 Purpose . 18
4.2.6.2 Pointing accuracy specification . 18
4.2.6.3 On-axis cross polarization isolation specification . 18
4.2.6.4 Conformance tests . 18
4.2.7 Cessation of emissions . 18
4.2.7.1 Justification . 18
4.2.7.2 Specification. 18
4.2.7.2.1 Specification 1: Mode of cessation of emissions . 18
4.2.7.2.2 Specification 2: Conditions under which the ES shall cease emissions. 19
4.2.7.2.3 Specification 3: Cessation of emissions . 19
4.2.7.2.4 Specification 4: Fault conditions . 19
4.2.7.3 Conformance tests . 20
4.2.8 Control and Monitoring Functions (CMFs) . 20
4.2.8.1 ES States . 20
4.2.8.1.1 General . 20
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 303 699 V1.1.1 (2021-02)
4.2.8.1.2 CMF state diagram . 21
4.2.8.2 Processor monitoring . 22
4.2.8.2.1 Justification . 22
4.2.8.2.2 Specification . 22
4.2.8.2.3 Conformance tests . 22
4.2.8.3 Transmit subsystem monitoring . 23
4.2.8.3.1 Justification . 23
4.2.8.3.2 Specification . 23
4.2.8.3.3 Conformance tests . 23
4.2.8.4 Power-on/Reset . 23
4.2.8.4.1 Justification . 23
4.2.8.4.2 Specification . 23
4.2.8.4.3 Conformance tests . 23
4.2.8.5 Control Channel (CC) and Response Channel (RC) . 23
4.2.8.5.1 Justification . 23
4.2.8.5.2 Specification . 23
4.2.8.5.3 Conformance tests . 24
4.2.8.6 Network control commands . 24
4.2.8.6.1 Justification . 24
4.2.8.6.2 Specification . 24
4.2.8.6.3 Conformance tests . 25
4.2.8.7 Initial burst transmission . 25
4.2.8.7.1 Justification . 25
4.2.8.7.2 Specification . 25
4.2.8.7.3 Conformance tests . 25
4.2.8.8 Inhibition of transmissions . 25
4.2.8.8.1 Justification . 25
4.2.8.8.2 Specification . 25
4.2.8.8.3 Conformance tests . 26
4.2.9 Receive antenna off-axis gain pattern . 26
4.2.9.1 Justification . 26
4.2.9.2 Specification. 26
4.2.9.3 Conformance tests . 26
4.2.10 Blocking performance . 26
4.2.10.1 Justification . 26
4.2.10.2 Specification. 27
4.2.10.3 Conformance tests . 27
4.2.11 Adjacent Signal Selectivity . 27
4.2.11.1 Justification . 27
4.2.11.2 Specification. 27
4.2.11.3 Conformance tests . 27
4.2.12 Image frequency rejection . 28
4.2.12.1 Justification . 28
4.2.12.2 Specification. 28
4.2.12.3 Conformance tests . 28
5 Testing for compliance with technical requirements . 28
5.1 Environmental conditions for testing . 28
5.2 Ancillary Equipment . 28
5.3 Nominated Bandwidth . 28
5.4 Interpretation of the measurement results . 29
6 Test methods for all aspects of the ES. 29
6.1 General . 29
6.1.1 General requirements . 29
6.1.2 Special considerations for the interpretation of measurement results . 29
6.1.3 Measuring receiver . 30
6.2 Off-axis spurious radiation . 31
6.2.1 General . 31
6.2.2 Test method . 31
6.2.2.1 General . 31
6.2.2.2 Multi-carrier operation . 31
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 303 699 V1.1.1 (2021-02)
6.2.3 Measurements up to 1 000 MHz . 32
6.2.3.1 Test site . 32
6.2.3.2 Measuring receivers . 32
6.2.3.3 Procedure . 32
6.2.4 Measurements above 1 000 MHz . 32
6.2.4.1 General . 32
6.2.4.2 Identification of the significant frequencies of spurious radiation . 33
6.2.4.2.1 Test site. 33
6.2.4.2.2 Procedure . 33
6.2.4.3 Measurement of radiated power levels of identified spurious radiation . 33
6.2.4.3.1 Test site. 33
6.2.4.3.2 Procedure . 34
6.2.4.4 Measurement of conducted spurious radiation at the antenna flange . 35
6.2.4.4.1 Test site. 35
6.2.4.4.2 Procedure . 35
6.3 On-axis spurious radiation . 36
6.3.1 Test method . 36
6.3.1.1 General . 36
6.3.1.2 Test site . 36
6.3.1.3 Method of measurement . 36
6.3.1.3.1 General . 36
6.3.1.3.2 Method of measurement at the antenna flange . 36
6.3.1.3.3 Method of measurement for an EUT with antenna . 38
6.4 Void . 39
6.5 Carrier suppression . 39
6.5.1 General . 39
6.5.2 Test method . 39
6.6 Antenna pointing . 40
6.6.1 General . 40
6.6.2 Test method . 40
6.7 Polarization angle alignment capability . 41
6.7.1 General . 41
6.7.2 Test site . 41
6.7.3 Procedure . 41
6.8 Cessation of emissions of the ES . 42
6.8.1 General . 42
6.8.2 Test Method . 42
6.8.2.1 Required documentation . 42
6.8.2.2 Cessation of emissions from the "Transmission enabled" state . 42
6.8.2.3 Cessation of emission from the "Transmission disabled" state . 42
6.8.2.4 Cessation of emission from the "Initial Phase" state . 43
6.8.2.4.1 EUTs transmitting initial bursts . 43
6.8.2.4.2 EUTs not transmitting initial bursts . 43
6.8.2.5 "Single action" means of cessation of emissions. 43
6.8.2.6 Fault conditions . 44
6.9 Control and monitoring functions . 44
6.9.1 General . 44
6.9.2 Test arrangement . 45
6.9.3 Processor monitoring- Test method . 45
6.9.4 Transmit subsystem monitoring-Test method . 45
6.9.5 Power-on/Reset-Test method . 45
6.9.6 Control Channel and Response Channel -Test method . 46
6.9.7 Network Control commands-Test method . 46
6.9.8 Initial burst transmission-Test method . 48
6.9.9 Inhibition of transmission-Test method . 48
6.10 Receive antenna off-axis gain pattern . 48
6.10.1 Test method .
...
Draft ETSI EN 303 699 V1.1.0 (2020-10)
HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Fixed earth stations communicating with non-geostationary
satellite systems in the 20 GHz and 30 GHz FSS bands;
Harmonised Standard for access to radio spectrum
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 699 V1.1.0 (2020-10)
Reference
DEN/SES-00444
Keywords
antenna, earth station, FSS, harmonised
standard, non-GSO, regulation, satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 699 V1.1.0 (2020-10)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms . 11
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General . 14
4.1.1 Environmental profile . 14
4.1.2 Operational configurations . 14
4.1.3 EIRP for networks of ESs . 14
Aggregate
4.1.4 Presentation of equipment for testing purposes . 15
4.1.5 Choice of model for testing . 15
4.1.6 Void . 15
4.1.7 Peak pointing accuracy . 15
4.2 Conformance requirements . 15
4.2.1 Off-axis spurious radiation . 15
4.2.1.1 Justification . 15
4.2.1.2 Specification. 15
4.2.1.3 Conformance tests . 16
4.2.2 On-axis spurious radiation . 16
4.2.2.1 Justification . 16
4.2.2.2 Specification. 17
4.2.2.2.1 "Carrier-on" radio state . 17
4.2.2.2.2 "Carrier-off" and "Emissions disabled" radio states . 17
4.2.2.3 Conformance tests . 17
4.2.3 Void . 17
4.2.4 Void . 17
4.2.5 Carrier suppression . 17
4.2.5.1 Justification . 17
4.2.5.2 Specification. 18
4.2.5.3 Conformance tests . 18
4.2.6 Antenna pointing accuracy . 18
4.2.6.1 Purpose . 18
4.2.6.2 Pointing accuracy specification . 18
4.2.6.3 On-axis cross polarization isolation specification . 18
4.2.6.4 Conformance tests . 18
4.2.7 Cessation of emissions . 18
4.2.7.1 Justification . 18
4.2.7.2 Specification. 18
4.2.7.2.1 Specification 1: Mode of cessation of emissions . 18
4.2.7.2.2 Specification 2: Conditions under which the ES shall cease emissions. 19
4.2.7.2.3 Specification 3: Cessation of emissions . 19
4.2.7.2.4 Specification 4: Fault conditions . 19
4.2.7.3 Conformance tests . 20
4.2.8 Control and Monitoring Functions (CMFs) . 20
4.2.8.1 ES States . 20
4.2.8.1.1 General . 20
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 699 V1.1.0 (2020-10)
4.2.8.1.2 CMF state diagram . 21
4.2.8.2 Processor monitoring . 22
4.2.8.2.1 Justification . 22
4.2.8.2.2 Specification . 22
4.2.8.2.3 Conformance tests . 22
4.2.8.3 Transmit subsystem monitoring . 23
4.2.8.3.1 Justification . 23
4.2.8.3.2 Specification . 23
4.2.8.3.3 Conformance tests . 23
4.2.8.4 Power-on/Reset . 23
4.2.8.4.1 Justification . 23
4.2.8.4.2 Specification . 23
4.2.8.4.3 Conformance tests . 23
4.2.8.5 Control Channel (CC) and Response Channel (RC) . 23
4.2.8.5.1 Justification . 23
4.2.8.5.2 Specification . 23
4.2.8.5.3 Conformance tests . 24
4.2.8.6 Network control commands . 24
4.2.8.6.1 Justification . 24
4.2.8.6.2 Specification . 24
4.2.8.6.3 Conformance tests . 25
4.2.8.7 Initial burst transmission . 25
4.2.8.7.1 Justification . 25
4.2.8.7.2 Specification . 25
4.2.8.7.3 Conformance tests . 25
4.2.8.8 Inhibition of transmissions . 25
4.2.8.8.1 Justification . 25
4.2.8.8.2 Specification . 25
4.2.8.8.3 Conformance tests . 26
4.2.9 Receive antenna off-axis gain pattern . 26
4.2.9.1 Justification . 26
4.2.9.2 Specification. 26
4.2.9.3 Conformance tests . 26
4.2.10 Blocking performance . 26
4.2.10.1 Justification . 26
4.2.10.2 Specification. 27
4.2.10.3 Conformance tests . 27
4.2.11 Adjacent Signal Selectivity . 27
4.2.11.1 Justification . 27
4.2.11.2 Specification. 27
4.2.11.3 Conformance tests . 27
4.2.12 Image frequency rejection . 28
4.2.12.1 Justification . 28
4.2.12.2 Specification. 28
4.2.12.3 Conformance tests . 28
5 Testing for compliance with technical requirements . 28
5.1 Environmental conditions for testing . 28
5.2 Ancillary Equipment . 28
5.3 Nominated Bandwidth . 28
5.4 Interpretation of the measurement results . 29
6 Test methods for all aspects of the ES. 29
6.1 General . 29
6.1.1 General requirements . 29
6.1.2 Special considerations for the interpretation of measurement results . 29
6.1.3 Measuring receiver . 30
6.2 Off-axis spurious radiation . 31
6.2.1 General . 31
6.2.2 Test method . 31
6.2.2.1 General . 31
6.2.2.2 Multi-carrier operation . 31
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 699 V1.1.0 (2020-10)
6.2.3 Measurements up to 1 000 MHz . 32
6.2.3.1 Test site . 32
6.2.3.2 Measuring receivers . 32
6.2.3.3 Procedure . 32
6.2.4 Measurements above 1 000 MHz . 32
6.2.4.1 General . 32
6.2.4.2 Identification of the significant frequencies of spurious radiation . 33
6.2.4.2.1 Test site. 33
6.2.4.2.2 Procedure . 33
6.2.4.3 Measurement of radiated power levels of identified spurious radiation . 33
6.2.4.3.1 Test site. 33
6.2.4.3.2 Procedure . 34
6.2.4.4 Measurement of conducted spurious radiation at the antenna flange . 35
6.2.4.4.1 Test site. 35
6.2.4.4.2 Procedure . 35
6.3 On-axis spurious radiation . 36
6.3.1 Test method . 36
6.3.1.1 General . 36
6.3.1.2 Test site . 36
6.3.1.3 Method of measurement . 36
6.3.1.3.1 General . 36
6.3.1.3.2 Method of measurement at the antenna flange . 36
6.3.1.3.3 Method of measurement for an EUT with antenna . 38
6.4 Void . 39
6.5 Carrier suppression . 39
6.5.1 General . 39
6.5.2 Test method . 39
6.6 Antenna pointing . 40
6.6.1 General . 40
6.6.2 Test method . 40
6.7 Polarization angle alignment capability . 41
6.7.1 General . 41
6.7.2 Test site . 41
6.7.3 Procedure . 41
6.8 Cessation of emissions of the ES . 42
6.8.1 General . 42
6.8.2 Test Method . 42
6.8.2.1 Required documentation . 42
6.8.2.2 Cessation of emissions from the "Transmission enabled" state . 42
6.8.2.3 Cessation of emission from the "Transmission disabled" state . 42
6.8.2.4 Cessation of emission from the "Initial Phase" state . 43
6.8.2.4.1 EUTs transmitting initial bursts . 43
6.8.2.4.2 EUTs not transmitting initial bursts . 43
6.8.2.5 "Single action" means of cessation of emissions. 43
6.8.2.6 Fault conditions . 44
6.9 Control and monitoring functions . 44
6.9.1 General . 44
6.9.2 Test arrangement . 45
6.9.3 Processor monitoring- Test method . 45
6.9.4 Transmit subsystem monitoring-Test method . 45
6.9.5 Power-on/Reset-Test method . 45
6.9.6 Control Channel and Response Channel -Test method . 46
6.9.7 Network Control commands-Test method . 46
6.9.8 Initial burst transmission-Test method . 48
6.9.9 Inhibition of transmission-Test method . 48
6.10 Receive antenna off-axis gain pattern . 48
6.10.1 Test method .
...
SLOVENSKI STANDARD
oSIST prEN 303 699 V1.1.0:2020
01-december-2020
Satelitske zemeljske postaje in sistemi (SES) - Fiksne zemeljske postaje, ki
komunicirajo z negeostacionarnimi satelitskimi sistemi FSS v pasovih 20 GHz in
30 GHz - Harmonizirani standard za dostop do radijskega spektra
Satellite Earth Stations and Systems (SES) - Fixed earth stations communicating with
non-geostationary satellite systems in the 20 GHz and 30 GHz FSS bands - Harmonised
Standard for access to radio spectrum
Ta slovenski standard je istoveten z: ETSI EN 303 699 V1.1.0 (2020-10)
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
oSIST prEN 303 699 V1.1.0:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 303 699 V1.1.0:2020
---------------------- Page: 2 ----------------------
oSIST prEN 303 699 V1.1.0:2020
Draft ETSI EN 303 699 V1.1.0 (2020-10)
HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Fixed earth stations communicating with non-geostationary
satellite systems in the 20 GHz and 30 GHz FSS bands;
Harmonised Standard for access to radio spectrum
---------------------- Page: 3 ----------------------
oSIST prEN 303 699 V1.1.0:2020
2 Draft ETSI EN 303 699 V1.1.0 (2020-10)
Reference
DEN/SES-00444
Keywords
antenna, earth station, FSS, harmonised
standard, non-GSO, regulation, satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 303 699 V1.1.0:2020
3 Draft ETSI EN 303 699 V1.1.0 (2020-10)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms . 11
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General . 14
4.1.1 Environmental profile . 14
4.1.2 Operational configurations . 14
4.1.3 EIRP for networks of ESs . 14
Aggregate
4.1.4 Presentation of equipment for testing purposes . 15
4.1.5 Choice of model for testing . 15
4.1.6 Void . 15
4.1.7 Peak pointing accuracy . 15
4.2 Conformance requirements . 15
4.2.1 Off-axis spurious radiation . 15
4.2.1.1 Justification . 15
4.2.1.2 Specification. 15
4.2.1.3 Conformance tests . 16
4.2.2 On-axis spurious radiation . 16
4.2.2.1 Justification . 16
4.2.2.2 Specification. 17
4.2.2.2.1 "Carrier-on" radio state . 17
4.2.2.2.2 "Carrier-off" and "Emissions disabled" radio states . 17
4.2.2.3 Conformance tests . 17
4.2.3 Void . 17
4.2.4 Void . 17
4.2.5 Carrier suppression . 17
4.2.5.1 Justification . 17
4.2.5.2 Specification. 18
4.2.5.3 Conformance tests . 18
4.2.6 Antenna pointing accuracy . 18
4.2.6.1 Purpose . 18
4.2.6.2 Pointing accuracy specification . 18
4.2.6.3 On-axis cross polarization isolation specification . 18
4.2.6.4 Conformance tests . 18
4.2.7 Cessation of emissions . 18
4.2.7.1 Justification . 18
4.2.7.2 Specification. 18
4.2.7.2.1 Specification 1: Mode of cessation of emissions . 18
4.2.7.2.2 Specification 2: Conditions under which the ES shall cease emissions. 19
4.2.7.2.3 Specification 3: Cessation of emissions . 19
4.2.7.2.4 Specification 4: Fault conditions . 19
4.2.7.3 Conformance tests . 20
4.2.8 Control and Monitoring Functions (CMFs) . 20
4.2.8.1 ES States . 20
4.2.8.1.1 General . 20
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 303 699 V1.1.0:2020
4 Draft ETSI EN 303 699 V1.1.0 (2020-10)
4.2.8.1.2 CMF state diagram . 21
4.2.8.2 Processor monitoring . 22
4.2.8.2.1 Justification . 22
4.2.8.2.2 Specification . 22
4.2.8.2.3 Conformance tests . 22
4.2.8.3 Transmit subsystem monitoring . 23
4.2.8.3.1 Justification . 23
4.2.8.3.2 Specification . 23
4.2.8.3.3 Conformance tests . 23
4.2.8.4 Power-on/Reset . 23
4.2.8.4.1 Justification . 23
4.2.8.4.2 Specification . 23
4.2.8.4.3 Conformance tests . 23
4.2.8.5 Control Channel (CC) and Response Channel (RC) . 23
4.2.8.5.1 Justification . 23
4.2.8.5.2 Specification . 23
4.2.8.5.3 Conformance tests . 24
4.2.8.6 Network control commands . 24
4.2.8.6.1 Justification . 24
4.2.8.6.2 Specification . 24
4.2.8.6.3 Conformance tests . 25
4.2.8.7 Initial burst transmission . 25
4.2.8.7.1 Justification . 25
4.2.8.7.2 Specification . 25
4.2.8.7.3 Conformance tests . 25
4.2.8.8 Inhibition of transmissions . 25
4.2.8.8.1 Justification . 25
4.2.8.8.2 Specification . 25
4.2.8.8.3 Conformance tests . 26
4.2.9 Receive antenna off-axis gain pattern . 26
4.2.9.1 Justification . 26
4.2.9.2 Specification. 26
4.2.9.3 Conformance tests . 26
4.2.10 Blocking performance . 26
4.2.10.1 Justification . 26
4.2.10.2 Specification. 27
4.2.10.3 Conformance tests . 27
4.2.11 Adjacent Signal Selectivity . 27
4.2.11.1 Justification . 27
4.2.11.2 Specification. 27
4.2.11.3 Conformance tests . 27
4.2.12 Image frequency rejection . 28
4.2.12.1 Justification . 28
4.2.12.2 Specification. 28
4.2.12.3 Conformance tests . 28
5 Testing for compliance with technical requirements . 28
5.1 Environmental conditions for testing . 28
5.2 Ancillary Equipment . 28
5.3 Nominated Bandwidth . 28
5.4 Interpretation of the measurement results . 29
6 Test methods for all aspects of the ES. 29
6.1 General . 29
6.1.1 General requirements . 29
6.1.2 Special considerations for the interpretation of measurement results . 29
6.1.3 Measuring receiver . 30
6.2 Off-axis spurious radiation . 31
6.2.1 General . 31
6.2.2 Test method . 31
6.2.2.1 General . 31
6.2.2.2 Multi-carrier operation . 31
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 303 699 V1.1.0:2020
5 Draft ETSI EN 303 699 V1.1.0 (2020-10)
6.2.3 Measurements up to 1 000 MHz . 32
6.2.3.1 Test site . 32
6.2.3.2 Measuring receivers . 32
6.2.3.3 Procedure . 32
6.2.4 Measurements above 1 000 MHz . 32
6.2.4.1 General . 32
6.2.4.2 Identification of the significant frequencies of spurious radiation . 33
6.2.4.2.1 Test site. 33
6.2.4.2.2 Procedure . 33
6.2.4.3 Measurement of radiated power levels of identified spurious radiation . 33
6.2.4.3.1 Test site. 33
6.2.4.3.2 Procedure . 34
6.2.4.4 Measurement of conducted spurious radiation at the antenna flange . 35
6.2.4.4.1 Test site. 35
6.2.4.4.2 Procedure . 35
6.3 On-axis spurious radiation . 36
6.3.1 Test method . 36
6.3.1.1 General . 36
6.3.1.2 Test site . 36
6.3.1.3 Method of measurement . 36
6.3.1.3.1 General . 36
6.3.1.3.2 Method of measurement at the antenna flange . 36
6.3.1.3.3 Method of measurement for an EUT with antenna . 38
6.4 Void . 39
6.5 Carrier suppression . 39
6.5.1 General . 39
6.5.2 Test method . 39
6.6 Antenna pointing . 40
6.6.1 General . 40
6.6.2 Test method . 40
6.7 Polarization angle alignment capability . 41
6.7.1 General . 41
6.7.2 Test site . 41
6.7.3 Procedure . 41
6.8 Cessation of emissions of the ES . 42
6.8.1 General . 42
6.8.2 Test Method . 42
6.8.2.1 Required documentation . 42
6.8.2.2 Cessation of emissions from the "Transmission enabled" state . 42
6.8.2.3 Cessation of emission from the "Transmission disabled" state . 42
6.8.2.4 Cessation of emission from the "Initial Phase" state . 43
6.8.2.4.1 EUTs transmitting initial bursts . 43
6.8.2.4.2 EUTs not transmitting initial bursts . 43
6.8.2.5 "Single action" means of cessation of emissions. 43
6.8.2.6 Fault conditions . 44
6.9 Control and monitoring functions . 44
6.9.1 General . 44
6.9.2 Test arrangement . 45
6.9.3 Processor monitoring- Test method .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.