IEC 60851-3:2023

Winding wires - Test methods - Part 3: Mechanical properties

IEC 60851-3:2023 is available as IEC 60851-3:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60851-3: 2023 specifies the following test methods for winding wires:
- Test 6: Elongation;
- Test 7: Springiness;
- Test 8: Flexibility and adherence;
- Test 11: Resistance to abrasion;
- Test 18: Heat bonding.
For definitions, general notes on test methods and the complete series of test methods for winding wires, IEC 60851-1 applies. This document also provides recommended friction test methods in Annex B. This fourth edition cancels and replaces the third edition published in 2009, Amendment 1:2013 and Amendment 2:2019. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) Clarification of the distance measurement for determining loss of adhesion in 6.6.3, 6.6.4 for fibre-covered wires and 6.6.5 for tape-wrapped wires.

Fils de bobinage - Méthodes d'essai - Partie 3: Propriétés mécaniques

IEC 60851-3:2023 est disponible sous forme de IEC 60851-3:2023 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.IEC 60851-3: 2023 spécifie les méthodes d’essai suivantes pour les fils de bobinage:
- Essai 6: Allongement;
- Essai 7: Effet de ressort;
- Essai 8: Souplesse et adhérence;
- Essai 11: Résistance à l’abrasion;.
- Essai 18: Thermoadhérence.
Pour les définitions, les généralités concernant les méthodes d’essai et les séries complètes des méthodes d’essai des fils de bobinage, c’est l’IEC 60851-1 qui s’applique. Le présent document donne aussi les méthodes d’essai de frottement recommandées dans l'Annexe B. Cette quatrième édition annule et remplace la troisième édition parue en 2009, l’Amendement 1 paru en 2013 et l’Amendement 2 paru en 2019. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente:
a) clarification de la mesure de distance visant à déterminer la perte d’adhérence en 6.6.3, en 6.6.4 pour les fils recouverts d’une enveloppe fibreuse et en 6.6.5 pour les fils rubanés.

General Information

• Status: Published
• Publication Date: 21-Aug-2023
• ICS: 29.060.10 - Wires
• Technical Committee: TC 55 - Winding wires
• Drafting Committee: WG 1 - TC 55/WG 1
• Current Stage: PPUB - Publication issued
• Start Date: 11-Sep-2023
• Completion Date: 22-Aug-2023

Relations

• Revises: IEC 60851-3:2009/AMD1:2013 - Amendment 1 - Winding wires - Test methods - Part 3: Mechanical properties
• Effective Date: 05-Sep-2023
• Revises: IEC 60851-3:2009 - Winding wires - Test methods - Part 3: Mechanical properties
• Effective Date: 05-Sep-2023
• Revises: IEC 60851-3:2009/AMD2:2019 - Amendment 2 - Winding wires - Test methods - Part 3: Mechanical properties
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 60851-3 ®
Edition 4.0 2023-08
REDLINE VERSION
INTERNATIONAL
STANDARD
colour
inside
Winding wires – Test methods –
Part 3: Mechanical properties
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Secretariat Tel.: [phone]
3, rue de Varembé [e-mail]
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always have
committee, …). It also gives information on projects, replaced access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and once
and French, with equivalent terms in 19 additional languages.
a month by email.
Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc
If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: [e-mail].
IEC 60851-3 ®
Edition 4.0 2023-08
REDLINE VERSION
INTERNATIONAL
STANDARD
colour
inside
Winding wires – Test methods –
Part 3: Mechanical properties
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.060.10 ISBN 978-2-8322-7448-4

– 2 – IEC 60851-3:2023 RLV © IEC 2023
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 8
4 Test 6: Elongation . 8
4.1 Elongation at fracture . 8
4.2 Tensile strength . 9
5 Test 7: Springiness . 9
5.1 General . 9
5.2 Round wire with a nominal conductor diameter from 0,080 mm up to and
including 1,600 mm . 9
5.2.1 Principle . 9
5.2.2 Equipment . 9
5.2.3 Procedure . 11
5.3 Round wire with a nominal conductor diameter over 1,600 mm and
rectangular wire . 12
5.3.1 Principle . 12
5.3.2 Equipment . 12
5.3.3 Specimen . 13
5.3.4 Procedure . 13
6 Test 8: Flexibility and adherence . 14
6.1 General . 14
6.2 Mandrel winding test . 14
6.2.1 Round wire . 14
6.2.2 Rectangular wire. 15
6.2.3 Covered bunched wire . 16
6.3 Stretching test (applicable to enamelled round wire with a nominal conductor
diameter over 1,600 mm) . 16
6.4 Jerk test (applicable to enamelled round wire with a nominal conductor
diameter up to and including 1,000 mm) . 17
6.5 Peel test (applicable to enamelled round wire with a nominal conductor
diameter over 1,000 mm) . 17
6.6 Adherence test . 19
6.6.1 General . 19
6.6.2 Enamelled rectangular wire . 19
6.6.3 Impregnated fibre covered round and rectangular wire . 19
6.6.4 Fibre covered enamelled round and rectangular wire . 19
6.6.5 Tape-wrapped round and rectangular wire (for adhesive tape only) . 20
7 Test 11: Resistance to abrasion (applicable to enamelled round wire) . 20
7.1 General . 20
7.2 Principle . 20
7.3 Equipment . 20
7.4 Procedure . 21
8 Test 18: Heat bonding (applicable to enamelled round wire with a nominal
conductor diameter over 0,050 mm up to and including 2,000 mm and to
enamelled rectangular wire) . 22

8.1 General . 22
8.2 Vertical bond retention of a helical coil . 22
8.2.1 General . 22
8.2.2 Nominal conductor diameter up to and including 0,050 mm . 22
8.2.3 Nominal conductor diameter over 0,050 mm up to and including

2,000 mm . 22
8.3 Bond strength of a twisted coil . 25
8.3.1 General . 25
8.3.2 Principle . 25
8.3.3 Equipment . 25
8.3.4 Specimen . 25
8.3.5 Procedure . 27
8.3.6 Result . 27
8.4 Enamelled rectangular wire heat bonding . 28
Annex A (informative) Bond strength of heat bonding wires . 30
A.1 Calculation of the temperature of the twisted coil specimen . 30
A.1.1 Method . 30
A.1.2 Temperature coefficient . 30
A.1.3 Calculation . 30
A.2 Determination of the heating period . 31
A.2.1 Voltage-time graphs. 31
A.2.2 Voltage at maximum temperature . 31
Annex B (informative) Friction test methods . 36
B.1 General . 36
B.2 Test A: Static coefficient of friction test method . 36
B.2.1 Test method (applicable to enamelled round wires with a nominal
conductor diameter from 0,050 mm up to and including 1,600 mm) . 36
B.2.2 Test apparatus . 36
B.3 Test B: First dynamic coefficient of friction test method . 37
B.3.1 Principle . 37
B.3.2 Method of test. 37
B.4 Test C: Second dynamic coefficient of friction test method (applicable to
enamelled round wires with a nominal conductor diameter from 0,050 mm up
to and including 1,600 mm) . 37
B.4.1 Test equipment . 37
B.4.2 Test specimen . 38
B.4.3 Specimen preparation . 38
B.4.4 Procedure . 39
B.5 Test D: Force of friction by the twisted pair method . 40
B.5.1 Enamelled round wires with a nominal conductor diameter from 0,1 mm
up to and including 1,500 mm . 40
B.5.2 Test method . 40
Bibliography . 46

Figure 1 – Test equipment to determine springiness . 10
Figure 2 – Construction and details of the mandrel (see Table 1) . 10
Figure 3 – Test equipment to determine springiness . 13
Figure 4 – Test equipment for mandrel winding test . 16
Figure 5 – Test equipment for jerk test . 17

– 4 – IEC 60851-3:2023 RLV © IEC 2023
Figure 6 – Test equipment for peel test . 18
Figure 7 – Scraper . 19
Figure 8 – Cross-section of the wire after removal of the coating . 19
Figure 9 – Test equipment for unidirectional scrape test . 21
Figure 10 – Test equipment for bond retention of a helical coil . 24
Figure 11 – Coil winder . 26
Figure 12 – Oval shape coil .
...

IEC 60851-3 ®
Edition 4.0 2023-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Winding wires – Test methods –
Part 3: Mechanical properties
Fils de bobinage – Méthodes d'essai –
Partie 3: Propriétés mécaniques
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni
utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et
les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.

IEC Secretariat Tel.: [phone]
3, rue de Varembé [e-mail]
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always have
committee, …). It also gives information on projects, replaced access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and once
and French, with equivalent terms in 19 additional languages.
a month by email.
Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc

If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: [e-mail].
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.

Recherche de publications IEC -  IEC Products & Services Portal - products.iec.ch
webstore.iec.ch/advsearchform Découvrez notre puissant moteur de recherche et consultez
La recherche avancée permet de trouver des publications IEC gratuitement tous les aperçus des publications. Avec un
en utilisant différents critères (numéro de référence, texte, abonnement, vous aurez toujours accès à un contenu à jour
comité d’études, …). Elle donne aussi des informations sur les adapté à vos besoins.
projets et les publications remplacées ou retirées.

Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
Le premier dictionnaire d'électrotechnologie en ligne au monde,
Restez informé sur les nouvelles publications IEC. Just
avec plus de 22 300 articles terminologiques en anglais et en
Published détaille les nouvelles publications parues.
français, ainsi que les termes équivalents dans 19 langues
Disponible en ligne et une fois par mois par email.
additionnelles. Egalement appelé Vocabulaire

Electrotechnique International (IEV) en ligne.
Service Clients - webstore.iec.ch/csc

Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
[e-mail].
IEC 60851-3 ®
Edition 4.0 2023-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Winding wires – Test methods –

Part 3: Mechanical properties
Fils de bobinage – Méthodes d'essai –

Partie 3: Propriétés mécaniques

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10  ISBN 978-2-8322-7372-2

– 2 – IEC 60851-3:2023 © IEC 2023
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 8
4 Test 6: Elongation . 8
4.1 Elongation at fracture . 8
4.2 Tensile strength . 9
5 Test 7: Springiness . 9
5.1 General . 9
5.2 Round wire with a nominal conductor diameter from 0,080 mm up to and
including 1,600 mm . 9
5.2.1 Principle . 9
5.2.2 Equipment . 9
5.2.3 Procedure . 11
5.3 Round wire with a nominal conductor diameter over 1,600 mm and
rectangular wire . 12
5.3.1 Principle . 12
5.3.2 Equipment . 12
5.3.3 Specimen . 13
5.3.4 Procedure . 13
6 Test 8: Flexibility and adherence . 14
6.1 General . 14
6.2 Mandrel winding test . 14
6.2.1 Round wire . 14
6.2.2 Rectangular wire. 15
6.2.3 Covered bunched wire . 16
6.3 Stretching test (applicable to enamelled round wire with a nominal conductor
diameter over 1,600 mm) . 16
6.4 Jerk test (applicable to enamelled round wire with a nominal conductor
diameter up to and including 1,000 mm) . 17
6.5 Peel test (applicable to enamelled round wire with a nominal conductor
diameter over 1,000 mm) . 17
6.6 Adherence test . 19
6.6.1 General . 19
6.6.2 Enamelled rectangular wire . 19
6.6.3 Impregnated fibre covered round and rectangular wire . 19
6.6.4 Fibre covered enamelled round and rectangular wire . 19
6.6.5 Tape-wrapped round and rectangular wire (for adhesive tape only) . 20
7 Test 11: Resistance to abrasion (applicable to enamelled round wire) . 20
7.1 General . 20
7.2 Principle . 20
7.3 Equipment . 20
7.4 Procedure . 21
8 Test 18: Heat bonding (applicable to enamelled round wire with a nominal
conductor diameter over 0,050 mm up to and including 2,000 mm and to
enamelled rectangular wire) . 22

8.1 General . 22
8.2 Vertical bond retention of a helical coil . 22
8.2.1 General . 22
8.2.2 Nominal conductor diameter up to and including 0,050 mm . 22
8.2.3 Nominal conductor diameter over 0,050 mm up to and including

2,000 mm . 22
8.3 Bond strength of a twisted coil . 25
8.3.1 General . 25
8.3.2 Principle . 25
8.3.3 Equipment . 25
8.3.4 Specimen . 25
8.3.5 Procedure . 27
8.3.6 Result . 27
8.4 Enamelled rectangular wire heat bonding . 28
Annex A (informative) Bond strength of heat bonding wires . 30
A.1 Calculation of the temperature of the twisted coil specimen . 30
A.1.1 Method . 30
A.1.2 Temperature coefficient . 30
A.1.3 Calculation . 30
A.2 Determination of the heating period . 31
A.2.1 Voltage-time graphs. 31
A.2.2 Voltage at maximum temperature . 31
Annex B (informative) Friction test methods . 36
B.1 General . 36
B.2 Test A: Static coefficient of friction test method . 36
B.2.1 Test method (applicable to enamelled round wires with a nominal
conductor diameter from 0,050 mm up to and including 1,600 mm) . 36
B.2.2 Test apparatus . 36
B.3 Test B: First dynamic coefficient of friction test method . 37
B.3.1 Principle . 37
B.3.2 Method of test.
...