Coaxial communication cables - Part 11: Sectional specification for semi-rigid cables with polyethylene (PE) dielectric

IEC 61196-11:2022 specifies the general requirements of semi-rigid coaxial communication cables with polyethylene (PE) dielectric, including material and construction, IEC type designation, identification, marking and labelling, standard ratings and characteristics, requirements of finished cables, quality assessment, delivery and storage, etc.
This part of IEC 61196 applies to semi-rigid coaxial communication cables with polyethylene (PE) dielectric and tubular outer conductor. These cables are widely used in the interconnection between wireless communication equipment and antenna, as well as RF and microwave electronic equipment, broadcast television, microwave relay, navigation, etc.
This second edition cancels and replaces the first edition published in 2016. This edition includes the following significant technical changes with respect to the previous edition:
a. The scope is more detailed.
b. Outer diameter ratings of the inner conductor recommended.
c. Dielectric: outer diameter ratings of the dielectric recommended.
d. IEC type designation introduced.
e. Standard ratings and characteristics: completely revised.
f. Requirements of finished cables: completely revised.

General Information

Status
Published
Publication Date
15-Mar-2022
Technical Committee
Drafting Committee
Current Stage
PPUB - Publication issued
Start Date
11-Apr-2022
Completion Date
16-Mar-2022
Ref Project

Relations

Buy Standard

Standard
IEC 61196-11:2022 - Coaxial communication cables - Part 11: Sectional specification for semi-rigid cables with polyethylene (PE) dielectric
English language
16 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


IEC 61196-11 ®
Edition 2.0 2022-03
INTERNATIONAL
STANDARD
Coaxial communication cables –
Part 11: Sectional specification for semi-rigid cables with polyethylene (PE)
dielectric
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always
committee, …). It also gives information on projects, replaced have access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and
and French, with equivalent terms in 19 additional languages.
once a month by email.
Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc

If you wish to give us your feedback on this publication or
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC 61196-11 ®
Edition 2.0 2022-03
INTERNATIONAL
STANDARD
Coaxial communication cables –

Part 11: Sectional specification for semi-rigid cables with polyethylene (PE)

dielectric
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.120.10 ISBN 978-2-8322-1086-9

– 2 – IEC 61196-11:2022 © IEC 2022
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Materials and cable construction . 7
4.1 Cable construction . 7
4.2 Inner conductor . 7
4.3 Dielectric . 8
4.4 Outer conductor . 8
4.5 Sheath . 8
5 IEC type designation . 9
5.1 Type name . 9
5.2 Variant . 9
5.3 Cable marking . 9
6 Identification, marking and labelling . 10
6.1 Cable identification . 10
6.2 Cable marking . 10
6.3 Labelling . 10
7 Standard rating and characteristics . 10
7.1 Nominal characteristic impedance . 10
7.2 Rated temperature range . 10
7.3 Operating frequency . 10
7.4 Average and peak power . 11
7.5 Bending radius . 11
8 Requirements of finished cables . 11
8.1 General . 11
8.2 Electrical requirements . 11
8.3 Environmental requirements . 13
8.4 Mechanical requirements . 14
8.5 Fire performance requirements . 15
8.6 Content of toxic and harmful substance . 15
9 Quality assessment . 16
10 Delivery and storage . 16

Table 1 – Rated temperature . 10
Table 2 – Maximum operating frequency . 11
Table 3 – Electrical requirements . 12
Table 4 – Environmental requirements . 13
Table 5 – Mechanical requirements. 14
Table 6 – Fire performance requirements . 15
Table 7 – Content of toxic and harmful substance . 15

INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
COAXIAL COMMUNICATION CABLES –

Part 11: Sectional specification for semi-rigid cables
with polyethylene (PE) dielectric

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 61196-6 has been prepared by subcommittee 46A: Coaxial cables, of IEC technical
committee 46: Cables, wires, waveguides, RF connectors, RF and microwave passive
components and accessories. It is an International Standard.
This second edition cancels and replaces the first edition published in 2016. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) Clause 1: The scope is more detailed.
b) Subclause 4.2: Outer diameter ratings of the inner conductor recommended.
c) Subclause 4.3: Dielectric: outer diameter ratings of the dielectric recommended.
d) Clause 5: IEC type designation introduced.
e) Clause 7: Standard ratings and characteristics: completely revised.

– 4 – IEC 61196-11:2022 © IEC 2022
f) Clause 8: Requirements of finished cables: completely revised.
The text of this International Standard is based on the following documents:
Draft Report on voting
46A/1554/FDIS 46A/1559/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications.
A list of all the parts in the IEC 61196 series, published under the general title Coaxial
communication cables, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
COAXIAL COMMUNICATION CABLES –

Part 11: Sectional specification for semi-rigid cables
with polyethylene (PE) dielectric

1 Scope
This part of IEC 61196 specifies the general requirements of semi-rigid coaxial communication
cables with polyethylene (PE) dielectric, including material and construction, IEC type
designation, identification, marking and labelling, standard ratings and characteristics,
requirements of finished cables, quality assessment, delivery and storage, etc.
This part of IEC 61196 applies to semi-rigid coaxial communication cables with polyethylene
(PE) dielectric and tubular outer conductor. These cables are widely used in the interconnection
between wireless communication equipment and antenna, as well as RF and microwave
electronic equipment, broadcast television, microwave relay, navigation, etc.
2 Normative references
The following documents are referred to
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.