IEC/IEEE 62582-2:2011/AMD1:2016
(Amendment)Amendment 1 - Nuclear power plants - Instrumentation and control important to safety - Electrical equipment condition monitoring methods - Part 2: Indenter modulus
Amendment 1 - Nuclear power plants - Instrumentation and control important to safety - Electrical equipment condition monitoring methods - Part 2: Indenter modulus
Amendement 1 - Centrales nucléaires de puissance - Instrumentation et contrôle-commande importants pour la sûreté - Méthodes de surveillance de l'état des matériels électriques - Partie 2: Module indenter
General Information
Relations
Standards Content (Sample)
IEC/IEEE 62582-2 ®
Edition 1.0 2016-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AM ENDMENT 1
AM ENDEMENT 1
Nuclear power plants – Instrumentation and control important to safety –
Electrical equipment condition monitoring methods –
Part 2: Indenter modulus
Centrales nucléaires de puissance – Instrumentation et contrôle-commande
importants pour la sûreté – Méthodes de surveillance de l’état des matériels
électriques –
Partie 2: Module indenter
IEC/IEEE 62582-2:2011-08/AMD1:2016-02(en-fr)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing being
secured. Requests for permission to reproduce should be addressed to either IEC at the address below or IEC’s
member National Committee in the country of the requester or from IEEE.
IEC Central Office Institute of Electrical and Electronics Engineers, Inc.
3, rue de Varembé 3 Park Avenue
CH-1211 Geneva 20 New York, NY 10016-5997
Switzerland United States of America
Tel.: +41 22 919 02 11 stds.ipr@ieee.org
Fax: +41 22 919 03 00 www.ieee.org
info@iec.ch
www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About the IEEE
IEEE is the world’s largest professional association dedicated to advancing technological innovation and excellence for
the benefit of humanity. IEEE and its members inspire a global community through its highly cited publications,
conferences, technology standards, and professional and educational activities.
About IEC/IEEE publications
The technical content of IEC/IEEE publications is kept under constant review by the IEC and IEEE. Please make sure
that you have the latest edition, a corrigendum or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 15 additional
documents. Available for PC, Mac OS, Android Tablets languages. Also known as the International
and iPad. Electrotechnical Vocabulary (IEV) online.
IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, IEC publications issued since 2002. Some entries have
replaced and withdrawn publications. been collected from earlier publications of IEC TC 37, 77,
86 and CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer
Service Centre: csc@iec.ch.
IEC/IEEE 62582-2 ®
Edition 1.0 2016-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AM ENDMENT 1
AM ENDEMENT 1
Nuclear power plants – Instrumentation and control important to safety –
Electrical equipment condition monitoring methods –
Part 2: Indenter modulus
Centrales nucléaires de puissance – Instrumentation et contrôle-commande
importants pour la sûreté – Méthodes de surveillance de l’état des matériels
électriques –
Partie 2: Module indenter
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 27.120.20 ISBN 978-2-8322-3157-9
– 2 – IEC/IEEE 62582-2:2011/AMD1:2016
IEC/IEEE 2016
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation.
IEEE Standards documents are developed within IEEE Societies and Standards Coordinating Committees of the
IEEE Standards Association (IEEE-SA) Standards Board. IEEE develops its standards through a consensus
development process, which brings together volunteers representing varied viewpoints and interests to achieve
the final product. Volunteers are not necessarily members of IEEE and serve without compensation. While IEEE
administers the process and establishes rules to promote fairness in the consensus development process, IEEE
does not independently evaluate, test, or verify the accuracy of any of the information contained in its
standards. Use of IEEE Standards documents is wholly voluntary. IEEE documents are made available for use
subject to important notices and legal disclaimers (see http://standards.ieee.org/IPR/disclaimers.html for more
information).
IEC collaborates closely with IEEE in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions of IEC on technical matters express, as nearly as possible, an international consensus of
opinion on the relevant subjects since each technical committee has representation from all interested IEC
National Committees. The formal decisions of IEEE on technical matters, once consensus within IEEE Societies
and Standards Coordinating Committees has been reached, is determined by a balanced ballot of materially
interested parties who indicate interest in reviewing the proposed standard. Final approval of the IEEE
standards document is given by the IEEE Standards Association (IEEE-SA) Standards Board.
3) IEC/IEEE Publications have the form of recommendations for international use and are accepted by IEC
National Committees/IEEE Societies in that sense. While all reasonable efforts are made to ensure that the
technical content of IEC/IEEE Publications is accurate, IEC or IEEE cannot be held responsible for the way in
which they are used or for any misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
(including IEC/IEEE Publications) transparently to the maximum extent possible in their national and regional
publications. Any divergence between any IEC/IEEE Publication and the corresponding national or regional
publication shall be clearly indicated in the latter.
5) IEC and IEEE do not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC and IEEE are not responsible
for any services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or IEEE or their directors, employees, servants or agents including individual
experts and members of technical committees and IEC National Committees, or volunteers of IEEE Societies
and the Standards Coordinating Committees of the IEEE Standards Association (IEEE-SA) Standards Board,
for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect,
or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this
IEC/IEEE Publication or any other IEC or IEEE Publications.
8) Attention is drawn to the normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that implementation of this IEC/IEEE Publication may require use of
material covered by patent rights. By publication of this standard, no position is taken with respect to the
existence or validity of any patent rights in connection therewith. IEC or IEEE shall not be held responsible for
identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal
validity or scope of Patent Claims or determining whether any licensing terms or conditions provided in
connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or
non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent
rights, and the risk of infringement of such rights, is entirely their own responsibility.
This amendment has been prepared by subcommittee 45A: Instrumentation, control and
electrical systems of nuclear facilities, of IEC technical committee 45: Nuclear
instrumentation, in cooperation with the Nuclear Power Engineering Committee of the Power
& Energy Society of the IEEE , under the IEC/IEEE Dual Logo Agreement between IEC and
IEEE.
This publication is published as an IEC/IEEE Dual Logo standard.
—————————
A list of IEEE participants can be found at the following URL: http://standards.ieee.org/downloads/62582-2/62582-2-amd1-
2016/62582-2-amd1-2016_wg-participants.pdf.
IEC/IEEE 2016
The text of this standard is based on the following IEC documents:
FDIS Report on voting
45A/1054/FDIS 45A/1067/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
The IEC Technical Committee and IEEE Technical Committee have decided that the contents
of this publication will remain unchanged until the stability date indicated on the IEC web site
under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
_____________
– 4 – IEC/IEEE 62582-2:2011/AMD1:2016
IEC/IEEE 2016
6 Measurement procedure
6.4 Instrumentation
Replace existing Figure 1 by the following new Figure 1:
Dimensions in millimetres
17,5°
≈ R0,1
IEC
Figure 1 – Geometry and dimensions of the profile
of the probe tip (truncated cone) used in the indenter
6.9 Determination of the value of the indenter modulus
Replace existing Figure 2 by the following new Figure 2 and add a note after Figure 2 as
follows:
d – d
2 1
0 0,1 0,2 0,3 0,4 0,5 0,6
Displacement (mm)
IEC
Figure 2 – Calculation of indenter modulus
–1
NOTE Some instruments used for indenter measurements show the result in load versus time (in N∙s ). The
–1 –1
value of the indenter modulus in N∙mm is then calculated as the value in N∙s divided by the probe velocity in
–1
mm∙s .
Load (N)
F – F
2 1
0,56
IEC/IEEE 2016
Annex A (informative)
A.1 Example of influence of variability in equipment dimensions and
construction
Replace existing Figure A.1 by the following new Figure A.1:
8 Thermally aged
8 o
1008 h at 120 C
Unaged
0 1 2 3 4 5 6 7 8
0 1 2 3 4 5 6 7 8
Time (s)
Time (s) IEC
IEC
–1
NOTE The probe velocity was 5,2 mm∙min and the indenter modulus values were calculated from the slope
–1
between 1 N and 4 N by division by 5,2∙60 .
Figure A.1 – Example of local variation of indenter modulus due to variation in
equipment dimensions and construction
Annex B (informative)
Replace existing Figure B.1 by the following new Figure B.1:
8 CSPE/EPDM
0 1 2 3 4 5 6 7 8 9
Time (s)
IEC
–1
NOTE The indenter modulus value was calculated from the slope between 1 N and 4 N by division by 5,162∙60 .
Figure B.1 – Example of measured force versus time
___________
Load (N)
Load (N)
Load (N)
– 6 – IEC/IEEE 62582-2:2011/AMD1:2016
IEC/IEEE 2016
AVANT-PROPOS
1) La Commission Electrotechnique Internationale (IEC) est une organisation mondiale de normalisation
composée de l'ensemble des comités électrotechniques nationaux (Comités nationaux de l'IEC). L'IEC a pour
objet de favoriser la coopération internationale pour toutes les questions de normalisation dans les domaines
de l'électricité et de l'électronique. A cet effet, l'IEC – entre autres activités – publie des Normes
internationales, des Spécifications techniques, des Rapports techniques, des Spécifications accessibles au
public (PAS) et des Guides (ci-après dénommés "Publication(s) de l'IEC"). Leur élaboration est confiée à des
comités d'études, aux travaux desquels tout Comité national intéressé par le sujet traité peut participer. Les
organisations internationales, gouvernementales et non gouvernementales, en liaison avec l'IEC, participent
également aux travaux.
Les normes de l’IEEE sont élaborées par les Sociétés de l’IEEE, ainsi que par les Comités de coordination des
normes du Conseil de normalisation de l’IEEE Standards Association (IEEE-SA). Ces normes sont
l’aboutissement d’un consensus, qui rassemble des bénévoles représentant divers points de vu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.