IEC 60335-2-6:2002/AMD2:2008
(Amendment)Amendment 2 - Household and similar electrical appliances - Safety - Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens and similar appliances
Amendment 2 - Household and similar electrical appliances - Safety - Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens and similar appliances
The contents of the corrigendum of February 2009 have been included in this copy.
Amendement 2 - Appareils électrodomestiques et analogues - Sécurité - Partie 2-6: Règles particulières pour les cuisinières, les tables de cuisson, les fours et les appareils fixes analogues
Le contenu du corrigendum de février 2009 a été pris en considération dans cet exemplaire.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC 60335-2-6
Edition 5.0 2008-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 2
AMENDEMENT 2
Household and similar electrical appliances – Safety –
Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens and
similar appliances
Appareils électrodomestiques et analogues – Sécurité –
Partie 2-6: Règles particulières pour les cuisinières, les tables de cuisson, les
fours et les appareils fixes analogues
IEC 60335-2-6 A2:2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 60335-2-6
Edition 5.0 2008-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 2
AMENDEMENT 2
Household and similar electrical appliances – Safety –
Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens
and similar appliances
Appareils électrodomestiques et analogues – Sécurité –
Partie 2-6: Règles particulières pour les cuisinières, les tables de cuisson, les
fours et les appareils fixes analogues
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
G
CODE PRIX
ICS 13.120; 97.040.20 ISBN 2-8318-9517-0
– 2 – 60335-2-6 Amend. 2 © IEC:2008
FOREWORD
This amendment has been prepared by IEC technical committee 61: Safety of household and
similar electrical appliances.
The text of this amendment is based on the following documents:
FDIS Report on voting
61/3410/FDIS 61/3423/RVD
Full information on the voting for the approval of this amendment can be found in the report
on voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the maintenance result date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC publication in
which to make products in accordance with the new requirements and to equip themselves for conducting new or
revised tests.
It is the recommendation of the committee that the content of this amendment be adopted for implementation
nationally not earlier than 12 months from the date of its publication.
The contents of the corrigendum of February 2009 have been included in this copy.
___________
FOREWORD
In the list of differences existing in some countries, add the following:
– 20.102: Heavier loads are used (USA).
INTRODUCTION
Replace the fifth paragraph by the following:
When a part 2 standard does not include additional requirements to cover hazards dealt with
in Part 1, Part 1 applies.
NOTE 1 This means that the technical committees responsible for the part 2 standards have determined that it is
not necessary to specify particular requirements for the appliance in question over and above the general
requirements.
This standard is a product family standard dealing with the safety of appliances and takes
precedence over horizontal and generic standards covering the same subject.
NOTE 2 Horizontal and generic standards covering a hazard are not applicable since they have been taken into
consideration when developing the general and particular requirements for the IEC 60335 series of standards. For
example, in the case of temperature requirements for surfaces on many appliances, generic standards, such as
ISO 13732-1 for hot surfaces, are not applicable in addition to Part 1 or part 2 standards.
60335-2-6 Amend. 2 © IEC:2008 – 3 –
1 Scope
Add to Note 101 the following new fourth dashed item:
– induction wok elements;
Replace the two dashed items in the third paragraph by the following:
– persons (including children) whose
• physical, sensory or mental capabilities; or
• lack of experience and knowledge
prevents them from using the appliance safely without supervision or instruction;
– children playing with the appliance.
3 Definitions
3.1.9.101 In the first paragraph, add “and induction wok elements” after “induction hob
elements”.
Replace the third paragraph by the following:
Induction hob elements are operated with vessels as specified in Figure 102 that contain
cooking oil at room temperature. Thermal controls are adjusted to their highest setting until
the oil temperature reaches 180 °C ± 4 °C and then adjusted so that this temperature is
maintained. The oil temperature is measured 10 mm above the centre of the bottom of the vessel.
Induction wok elements are operated with a wok having an equivalent sphere diameter that
does not differ from the equivalent sphere diameter of the induction wok element cavity by
more than %.
− 1
The wok is made of low carbon steel having a maximum carbon content of 0,08 %. The wok is
filled to approximately half of its height with cooking oil at room temperature. Thermal controls
are adjusted to their highest setting until the oil temperature reaches 180 °C ± 4 °C and then
adjusted so that this temperature is maintained. The oil temperature is measured 10 mm
above the centre of the bottom of the vessel.
In the existing fourth paragraph, add “, other than induction wok elements,” after “hob
elements”.
3.108 Add “or one induction wok element” after “induction hob element”.
Add the following new definition:
3.118
induction wok element
induction hob element with the hob surface of an approximate spherical shape to accept a
wok
7 Marking and instructions
7.1 In the addition, add “and induction wok elements” after “induction hob elements”.
7.6 In the addition, replace “5010 of IEC 60417-1” by “IEC 60417-5010 (2002-10)”.
– 4 – 60335-2-6 Amend. 2 © IEC:2008
7.12 Add the following:
The instructions for hobs shall state that the appliance is not intended to be operated by
means of an external timer or separate remote-control system.
The instructions for hobs incorporating an induction wok element shall contain a list of
vessels that can be used, unless the manufacturer provides a wok with the appliance.
The instructions for ovens that have shelves shall include details indicating the correct
installation of the shelves.
Add the following new subclause:
7.103 For cooking ranges that are normally placed on the floor and that have horizontally
hinged oven doors with a hinge height of less than 430 mm from the floor, if a stabilizing
means is necessary in order to comply with the test of 20.102, then
• the stabilizing means shall be marked, in lettering at least 3 mm high, with the substance
of the following warning:
WARNING: In order to prevent tipping of the appliance, this stabilizing means must be
installed. Refer to the instructions for installation.
NOTE Commonly available fixing hardware, such as screws and bolts, need not be marked or delivered with the
appliance.
• the appliance shall be marked, in lettering at least 3 mm high, at the point of supply entry
and at least one other point to draw the attention of the user to the need to stabilize the
appliance.
Compliance is checked by inspection and measurement.
10 Power input and current
10.1 In the addition, add “and induction wok elements” after “induction hob elements”.
10.2 In the addition, add “and induction wok elements” after “induction hob elements”.
11 Heating
11.4 In the addition, add “and induction wok elements” after “Induction hob elements”.
11.7.101 Add “and induction wok elements” after “Induction hob elements”.
13 Leakage current and electric strength at operating temperature
13.1 In the addition, add “and induction wok elements” after “Induction hob elements”.
16 Leakage current and electric strength
16.1 In the addition, add “and induction wok elements” after “Induction hob elements”.
60335-2-6 Amend. 2 © IEC:2008 – 5 –
19 Abnormal operation
19.1 In the addition, add the following sentence at the end of the first paragraph:
In addition, 19.101 is not applicable to induction wok elements.
19.2 In the addition, add “or an induction wok element” after “induction hob element” in
the third paragraph and “and induction wok elements” after “Induction hob elements” in
the fifth paragraph.
Add the following subclause:
19.11.4 Addition:
During the test of the stand-by-mode, a suitable vessel is placed on the cooking zone if a
pan detector is incorporated.
19.13 Replace the second paragraph of the addition by the following:
The temperature in the centre of ovens during the test of 19.4 shall not exceed 425 °C
whenever the oven door can be opened.
In the third and fourth paragraphs of the addition, add “and induction wok elements” after
“induction hob elements”.
19.102 Add “and induction wok elements” after “Induction hob elements”.
20 Stability and mechanical hazards
20.101 Replace the first paragraph of the test specification by the following:
Compliance is checked by the following test and by the test of 20.102 if relevant.
Add the following paragraph after Note 3:
Cooking ranges are tested without fitting any stabilizing means that are specified in the
instructions for installation.
Replace the existing Note 4 by the following:
Damage and deformation of doors and hinges are ignored.
Add the following new subclause:
20.102 For cooking ranges that are normally placed on the floor and that have horizontally
hinged oven doors with a hinge height of less than 430 mm from the floor, the test of 20.101
is repeated, except that:
– the cooking range is fitted with the stabilizing means, if any, specified in the instructions
for installation;
– the mass of the load on the oven doors is increased to 50 kg, or the mass of 22,5 kg is
placed at the centre of the outer edge of the oven door, whichever gives the most
unfavourable results.
The cooking range shall not tilt.
Damage and deformation of doors and hinges are ignored.
– 6 – 60335-2-6 Amend. 2 © IEC:2008
21 Mechanical strength
21.101 Add the following to the test specification:
Ovens with shelves that can be withdrawn and that are
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.