IEC 63241-2-4:2024
(Main)Electric motor-operated tools - Dust measurement procedure - Part 2-4: Particular requirements for hand-held sanders
Electric motor-operated tools - Dust measurement procedure - Part 2-4: Particular requirements for hand-held sanders
IEC 63241-2-4:2024 supplements or modifies the corresponding clauses in IEC 63241-1, so as to convert it into the IEC Standard: Electric motor-operated tools – Dust measurement procedure - Particular requirements for hand-held sanders.
Where a particular subclause of IEC 63241-1 is not mentioned in this document, that subclause applies as far as relevant. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 63241-1 is to be adapted accordingly.
This document applies to sanders with the exception of all types of rotating disc-type sanders, which are covered by IEC 63241-2-3.
General Information
Standards Content (Sample)
IEC 63241-2-4 ®
Edition 1.0 2024-08
INTERNATIONAL
STANDARD
Electric motor-operated tools – Dust measurement procedure –
Part 2-4: Particular requirements for hand-held sanders
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews, graphical symbols and the glossary.
committee, …). It also gives information on projects, replaced With a subscription you will always have access to up to date
and withdrawn publications. content tailored to your needs.
IEC Just Published - webstore.iec.ch/justpublished
Electropedia - www.electropedia.org
Stay up to date on all new IEC publications. Just Published
The world's leading online dictionary on electrotechnology,
details all new publications released. Available online and once
containing more than 22 500 terminological entries in English
a month by email.
and French, with equivalent terms in 25 additional languages.
Also known as the International Electrotechnical Vocabulary
IEC Customer Service Centre - webstore.iec.ch/csc
(IEV) online.
If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC 63241-2-4 ®
Edition 1.0 2024-08
INTERNATIONAL
STANDARD
Electric motor-operated tools – Dust measurement procedure –
Part 2-4: Particular requirements for hand-held sanders
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 25.140.30 ISBN 978-2-8322-9533-5
– 2 – IEC 63241-2-4:2024 © IEC 2024
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Test procedure . 6
5 Instrumentation . 8
6 Information to be reported . 8
Bibliography . 10
Figure 101 – Test set-up for sanding gypsum blocks . 8
Figure 102 – A-support . 9
Table 101 – Operating conditions for sanders when sanding gypsum blocks . 6
Table 102 – Operating conditions for sanders when sanding wood . 7
Table 103 – Operating conditions for sanders when sanding a wooden floor . 7
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRIC MOTOR-OPERATED TOOLS
DUST MEASUREMENT PROCEDURE –
Part 2-4: Particular requirements for hand-held sanders
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 63241-2-4 has been prepared by IEC technical committee 116: Safety of motor-operated
electric tools. It is an International Standard.
The text of this International Standard is based on the following documents:
Draft Report on voting
116/799/FDIS 116/822/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
– 4 – IEC 63241-2-4:2024 © IEC 2024
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
This document is to be used in conjunction with the first edition of IEC 63241-1:2023.
This document supplements or modifies the corresponding clauses in IEC 63241-1, so as to
convert it into the IEC Standard: Electric motor-operated tools – Dust measurement procedure
– Particular requirements for hand-held sanders.
Where a particular subclause of IEC 63241-1 is not mentioned in this document, that subclause
applies as far as relevant. Where this document states "addition", "modification" or
"replacement", the relevant text in IEC 63241-1 is to be adapted accordingly.
The fol
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.