TC 116 - Safety of motor-operated electric tools

IEC 62841-1:2024 Amendment 1

IEC 62841-1:2014 deals with the safety of electric motor-operated or magnetically driven:
- hand-held tools (IEC 62841-2);
- transportable tools (IEC 62841-3);
- lawn and garden machinery (IEC 62841-4). The above listed categories are hereinafter referred to as "tools" or "machines". The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Tools with electric heating elements are within the scope of this standard. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This standard is scheduled to cancel and replace the fourth edition of IEC 60745-1, published in 2006, the first edition of IEC 61029-1, published in 1990, and the fifth edition of IEC 60335-1, published in 2010, only with respect to requirements concerning lawn and garden machinery. The latter publications remain valid until they are withdrawn. This standard constitutes a technical revision. This edition includes the following significant technical changes with respect to the fourth edition of IEC 60745-1:
- requirements in various clauses introduced or modified in order to include the requirements for transportable tools and lawn and garden machinery (formerly covered by IEC 61029-1 and IEC 60335-1);
- leakage current test and electric strength test moved from former Clauses 13 and 15 to Annexes C and D;
- former Clauses 29, 30 and 31 renumbered to become Clauses 6, 13 and 15;
- requirements for electronic safety critical functions added to Clause 18;
- requirements for switches revised and moved from Annex I to Clause 23;
- clarifications in respect to soft materials (elastomers) added to Clauses 9, 19 and 13;
- test finger in Figure 1 of IEC 60745-1 and test probe in Figure 2 of IEC 60745-1 replaced by references to basic IEC standards;
- requirements for Li-Ion battery systems added to Annexes K and L and Annex M was removed. Key words: Tools, Electric-Motor-Operated, Hand held, Transportable, Lawn and Garden The contents of the corrigenda of May 2014 and of October 2015 have been included in this copy.

IEC 62841-2-17: 2024 Amendment 1

IEC 62841-2-17:2017 applies to routers intended for cutting slots into or shaping the edge of various materials. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3.
This part of IEC 62841 does not apply to jointers.
Routers that are primarily used for trimming the edge of materials are also known as trimmers.
Routers that are used to cut various materials through the rotary action are also known as rotary cutters.
This Part 2-17 is to be used in conjunction with the first edition of IEC 62841-1:2014.
The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.

IEC 62841-2-14: 2024 Amendment

IEC 62841-2-14:2015 applies to hand-held planners the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Planner, Hand held, Cutting head
This publication is to be read in conjunction with IEC 62841-1:2014.

IEC 62841-2-4:2014 applies to hand-held sanders and polishers with the exception of disc-type tools covered by IEC 62841-2-3. Tools covered by this standard include but are not limited to belt sanders, drum sanders or polishers, reciprocating sanders or polishers, orbital sanders or polishers and random orbit sanders or polishers. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Sander, Polisher, Belt, Drum Orbital, Reciprocating, Random Orbit
This publication is to be read in conjunction with IEC 62841-1:2014. The contents of the corrigendum of October 2015 have been included in this copy.

IEC 63241-2-14:2025 applies to planers.
This document is to be used in conjunction with the first edition of IEC 63241-1:2023.
This document supplements or modifies the corresponding clauses in IEC 63241-1, so as to convert it into the IEC Standard: Particular requirements for hand-held planers.
Where a particular subclause of IEC 63241-1 is not mentioned in this document, that subclause applies as far as reasonable. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 63241-1 is to be adapted accordingly.

IEC 63241-2-22: 2025 applies to hand-held cut-off machines and wall chasers.
This document is to be used in conjunction with the first edition of IEC 63241-1:2023.
This document supplements or modifies the corresponding clauses in IEC 63241-1, so as to convert it into the IEC Standard: Particular requirements for hand-held cut-off machines and wall chasers.
Where a particular subclause of Part 1 is not mentioned in this Part 2-22, that subclause applies as far as relevant. Where this standard states "addition", "modification" or "replacement", the relevant text in Part 1 is to be adapted accordingly.

IEC 63241-2-17:2025 applies to routers and trimmers.
This document is to be used in conjunction with the first edition of IEC 63241-1:2023.
This document supplements or modifies the corresponding clauses in IEC 63241-1, so as to convert it into the IEC Standard: Particular requirements for hand-held routers and trimmers.
Where a particular subclause of IEC 63241-1 is not mentioned in this document, that subclause applies as far as reasonable. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 63241-1 is to be adapted accordingly.

IEC 63241-3-1:2025 applies to transportable table saws intended to cut wood or wood-based materials.
This document is to be used in conjunction with the first edition of IEC 63241-1:2023.
Where a particular subclause of IEC 63241-1 is not mentioned in this document, that subclause applies as far as reasonable. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 63241-1 is to be adapted accordingly.

IEC 62841-2-8:2016 applies to hand-held shears and nibblers the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Keywords: Shear, Nibbler, Hand-held tool, Transportable tool
This publication is to be read in conjunction with IEC 62841-1:2014.

IEC 62841-2-9: 2025 Amendment 1

IEC 62841-2-8: 2025 Amendment 1

IEC 62841-2-5:2014 applies to hand-held circular saws. This standard does not apply to saws designed for use with abrasive wheels. Saws designed for use with abrasive wheels as cut-off machines are covered by IEC 62841-2-22. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Saw, Circular, Cutting,
This publication is to be read in conjunction with IEC 62841-1:2014.

IEC 62841-2-9:2015 applies to hand-held tappers and threaders. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Tapper, Threader, Internal Screw Threads, External Screw Threads
This publication is to be read in conjunction with IEC 62841-1:2014. The contents of the corrigendum of October 2015 have been included in this copy.

IEC 62841-2-5: 2025 Amendment 1

IEC 62841-4-8:2025 specifies safety requirements and their verification for the design and construction of hand fed, shredders/chippers with an integral electric motor, with or without vacuum assisted collection, which are designed to reduce organic material to smaller pieces and are used in a stationary position by an operator standing on the ground. This document applies to shredders/chippers with feed intake openings or feed safety openings that in total will fit into a square of 250 mm x 250 mm.
NOTE 101 The requirements for the measurement of the square of 250 mm x 250 mm are specified in 19.101.1.
In this document, shredders/chippers are referred to collectively as machine(s).
This document does not cover requirements for
- machines powered by combustion engines; or
- machines driven by an external power source; or
- machines with powered discharge intended to broadcast material or load vehicles; or
- machines with mechanically powered feed intake or attachments; or
- wood chippers for forestry, agriculture, horticulture and landscaping.
This document is to be used in conjunction with IEC 62841‑1:2014.
This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for shredders/chippers.

IEC 62841-2-21:2017 applies to hand-held drain cleaners (drain cleaners are also known as pipe cleaners) the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3.
This standard does not apply to transportable drain cleaners.
This standard does not apply to machines that use a solid rod to clean drains.
This Part 2-21 is to be used in conjunction with the first edition of IEC 62841-1:2014.
The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.

IEC 62841-2-21: 2024 Amendment 1

IEC 62841-2-10:2017 applies to mixers the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3.
Mixers are not considered to be tools with a liquid system.
This standard does not apply to drills and impact drills, even if they can be used as a mixer.
This Part 2-10 is to be used in conjunction with the first edition of IEC 62841-1:2014 .
The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.
Key words: Mixer, Hand-held tool, Safety

IEC 63241-2-5:2024 supplements or modifies the corresponding clauses in IEC 63241-1, so as to convert it into the IEC Standard: Electric motor-operated tools – Dust measurement procedure – Particular requirements for hand-held circular saws.
Where a particular subclause of IEC 63241-1 is not mentioned in this document, that subclause applies as far as relevant. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 63241-1 is to be adapted accordingly.

IEC 62841-4-1:2017 applies to chain saws for cutting wood and designed for use by one person. This standard does not cover chain saws designed for use in conjunction with a guide-plate and riving knife or in any other way such as with a support or as a stationary or transportable machine.
This standard does not apply to chain saws for tree service as defined in ISO 11681-2; or pole-mounted pruners.
Pole-mounted pruners will be covered by a future part of IEC 62841.
The chain saws covered by this standard are designed only to be operated with the right hand on the rear handle and the left hand on the front handle.
This Part 4-1 is to be used in conjunction with the first edition of IEC 62841-1:2014.
The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.

IEC 62841-4-1:2024 Amendment 1

IEC 62841-3-14: 2024 Amendment 1

IEC 62841-3-14:2017 applies to transportable drain cleaners. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3.
Drain cleaners are also known as pipe cleaners.
This standard does not apply to hand-held drain cleaners. Hand-held drain cleaners are covered by IEC 62841-2-21.
This standard does not apply to high pressure cleaners to clean drains. High pressure cleaners are covered by IEC 60335-2-79.
This standard does not apply to machines that use a solid rod to clean drains
This Part 3-14 is to be used in conjunction with the first edition of IEC 62841-1:2014.
The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.

IEC 62841-2-3:2020: applies to hand-held grinders, disc-type polishers and disc-type sanders, including angle, straight and vertical tools, intended for use on various materials except magnesium, with a rated capacity not exceeding 230 mm. For grinders, the rated no-load speed does not exceed a peripheral speed of the accessory of 80 m/s at rated capacity.
This standard does not apply to dedicated cut-off machines.
This standard does not apply to orbital polishers and orbital sanders.
This standard does not apply to die grinders.
This Part 2-3 is to be used in conjunction with the first edition of IEC 62841-1:2014.
The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. The contents of the corrigendum of April 2021 have been included in this copy.

IEC 62841-4-4: 2024 Amendment 1

IEC 62841-4-4:2020 This document applies to hand-held and walk-behind lawn trimmers and lawn edge trimmers, used by a standing operator for cutting grass, weeds or similar soft vegetation, and grass trimmers, brush cutters and brush saws used by a standing operator for cutting grass, weeds, brush, bushes, saplings and similar vegetation.
This document does not apply to
– hand-held machines having a mass of 18 kg or greater;
– self-propelled lawn trimmers or lawn edge trimmers;
– scissors type lawn trimmers and lawn edge trimmers;
– machines equipped with metallic cutting accessories consisting of more than one piece, e.g. pivoting chains or flail blades;
– edgers with rigid and/or metallic cutting devices.
Annex EE provides an informative summary of characteristics for lawn trimmers, lawn edge trimmers, grass trimmers, brush cutters and brush saws.
Brush cutters and brush saws covered by this document are designed only to be operated with the machine to the right of the operator.

The content of the corrigendum 1 (2024-12) has been included in this copy.

IEC 62841-3-8: 2024 applies to transportable single spindle vertical moulders, with a maximum tool holder diameter of 200 mm, designed to cut wood and analogue materials also covered with plastic laminate or edgings by hand-feed operation.
NOTE 101 Single spindle vertical moulders other than transportable are covered by ISO 19085-6:2024.
This document is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for transportable single spindle vertical moulders.

IEC 63241-2-11:2024 supplements or modifies the corresponding clauses in IEC 63241-1, so as to convert it into the IEC Standard: Electric motor-operated tools – Dust measurement procedure – Particular requirements for hand-held reciprocating saws.
Where a particular subclause of IEC 63241-1 is not mentioned in this document, that subclause applies as far as relevant. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 63241-1 is to be adapted accordingly.

IEC 62841-3-11:2024 applies to transportable combined mitre and bench saws intended to be used with a toothed saw blade for cutting wood and analogous materials, plastics and nonferrous metals except magnesium with a saw blade diameter not exceeding 315 mm, which hereinafter is simply referred to as saw or tool.
This document does not apply to:
- saws intended to cut other metals, such as magnesium, steel and iron, or food;
- saws with an automatic feeding device;
- saws designed for use with abrasive wheels;
- saws designed for use with dado blades;
- single function bench or table saws;
- single function mitre saws;
- combined mitre and bench saws other than transportable.
NOTE 101 Transportable saws intended to cut ferrous metals will be covered by a future part of IEC 62841-3.
NOTE 102 Transportable tools designed for use with abrasive wheels are covered by IEC 62841-3-10:2015.
NOTE 103 Transportable table saws are covered by IEC 62841-3-1:2014.
NOTE 104 Transportable mitre saws are covered by IEC 62841-3-9:2020.
NOTE 105 In Europe (EN IEC 62841-3-11), the following additional NOTE applies:
NOTE Z101 Combined mitre and bench saws other than transportable are covered by EN 1870-3:2014.
This document is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for transportable combined mitre and bench saws.

IEC 62841-3-15:2024 is to be used in conjunction with the first edition of IEC 62841-1 (2014).
This document supplements or modifies the corresponding clauses in IEC 62841-1:2014, so as to convert it into the IEC Standard: Particular requirements for transportable magnetic drills.
Where a particular subclause of IEC 62841-1:2014 is not mentioned in this Part 3-15, that subclause applies as far as relevant. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 62841-1:2014 is to be adapted accordingly.
IEC 62841-1:2014, Clause 1 is applicable, except as follows.
Addition: This document applies to transportable magnetic drills which can include a liquid system.
The content of the corrigendum 1 (2025-02) has been included in this copy.

IEC 63241-2-4:2024 supplements or modifies the corresponding clauses in IEC 63241-1, so as to convert it into the IEC Standard: Electric motor-operated tools – Dust measurement procedure - Particular requirements for hand-held sanders.
Where a particular subclause of IEC 63241-1 is not mentioned in this document, that subclause applies as far as relevant. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 63241-1 is to be adapted accordingly.
This document applies to sanders with the exception of all types of rotating disc-type sanders, which are covered by IEC 63241-2-3.

IEC 63241-2-3:2024 supplements or modifies the corresponding clauses in IEC 63241-1, so as to convert it into the IEC Standard: Particular requirements for hand-held concrete grinders and disc-type sanders.
Where a particular subclause of IEC 63241-1 is not mentioned in this document, that subclause applies as far as reasonable. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 63241-1 is to be adapted accordingly.

IEC 62841-3-4:2016 applies to transportable bench grinders that can be equipped with one or two accessories as follows:
- type 1 grinding wheels in accordance with ISO 603-4:1999 with a diameter not exceeding 310 mm and a thickness not exceeding 55 mm;
- wire brushes with a diameter not exceeding 310 mm and a thickness not exceeding 55 mm;
- polishing wheels with a diameter not exceeding 310 mm and with a peripheral speed of any accessory between 10 m/s and 50 m/s. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication Keywords: Bench Grinder, Hand-held tool, Transportable tool
This publication is to be read in conjunction with IEC 62841-1:2014. The contents of the corrigendum of December 2016 have been included in this copy.

IEC 62841-2-16:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held fastener driving tools. Where a particular subclause of IEC 62841-1 is not mentioned in this document, that subclause applies as far as reasonable. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 62841-1 is to be adapted accordingly.
IEC 62841-1:2014, Clause 1 is applicable, except as follows:
Addition: This document applies to hand-held fastener driving tools
- intended for driving fasteners into or through concrete, fabric, fiberboard, metal, plastic, wood, wood products, cartons, and other materials; and
- whose energy to drive the fastener is derived directly or indirectly from an electric motor or magnetic drive.
This document does not apply to pneumatically driven tools where the compressed gas comes from an external source, such as a compressor or a tank.
This document does not apply to tools powered by combustible gases, even if electrically ignited.
NOTE 101 Tools powered by compressed air or combustible gases are covered by ISO 11148-13:2017.

IEC 62841-2-20:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held band saws. Where a particular subclause of IEC 62841-1 is not mentioned in this document, that subclause applies as far as reasonable. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 62841-1 is to be adapted accordingly.
IEC 62841-1:2014, Clause 1 is applicable, except as follows:
This document applies to hand-held band saws.

IEC 62841-2-19:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held jointers. IEC 62841-1:2014, Clause 1 is applicable, except as follows: This document applies to hand-held jointers for cutting into wood or materials with similar physical characteristics such as, for example, chipboard, fibreboard and plywood.

IEC 62841-2-23:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held die grinders and small rotary tools. IEC 62841-1:2014, Clause 1 is applicable, except as follows:
This document applies to hand-held die grinders and to small rotary tools for mounted accessories not exceeding 55 mm in diameter and for mounted sanding accessories not exceeding 80 mm in diameter such as:
- threaded cones and plugs that are threaded on a mandrel with an unrelieved shoulder flange,
- mandrel mounted wheels, and
- rotary files
with a rated speed not exceeding a peripheral speed of the accessory of 80 m/s at rated capacity.
This document does not apply to straight and vertical grinders utilizing flanges for driving an abrasive accessory.
NOTE 101 Straight and vertical grinders are covered by IEC 62841-2-3.

IEC 62841-2-18:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held strapping tools. Where a particular subclause of IEC 62841-1 is not mentioned in this document, that subclause applies as far as reasonable. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 62841-1 is to be adapted accordingly. This document applies to hand-held strapping tools.

IEC 62841-3-3:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for transportable planers and thicknessers.
IEC 62841-1:2014, Clause 1 is applicable, except as follows:
This document applies to transportable planers, thicknessers and combined planers and thicknessers intended for cutting wood and analogous materials with a maximum planing width of 330 mm.
This document does not apply to planers, thicknessers or combined planers and thicknessers other than transportable.
NOTE 101 ISO 19085-7:2019 gives requirements for planers, thicknessers or combined planers and thicknessers other than transportable.

IEC 63241-2-1:2024 supplements or modifies the corresponding clauses in IEC 63241-1, so as to convert it into the IEC Standard: Electric motor-operated tools - Dust measurement procedure - Particular requirements for hand-held core drills.
Where a particular subclause of IEC 63241-1:2023 is not mentioned in this Part 2-1, that subclause applies as far as relevant. Where this standard states "addition", "modification" or "replacement", the relevant text in Part 1 is to be adapted accordingly.

IEC 62841-2-7:2024 deals with the safety of electric motor-operated hand-held spray guns for non-flammable materials. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This Part 2-7 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.

IEC 62841-2-12:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held concrete vibrators. IEC 62841-1:2014, Clause 1 is applicable, except as follows.
Addition: This document applies to hand-held concrete vibrators.