IEC 61580:1995/COR1:2006
(Corrigendum)Corrigendum 1 - Measurement of return loss on waveguide and waveguide assemblies
Corrigendum 1 - Measurement of return loss on waveguide and waveguide assemblies
Corrigendum 1 - Mesure des pertes de réflexion dans un guide d'ondes et des assemblages de guides d'onde
General Information
Standards Content (Sample)
CEI 61580 IEC 61580
(Première édition – 1995) (First edition – 1995)
Mesure des pertes de réflexion dans un Measurement of return loss on waveguide
guide d’ondes et des assemblages de and waveguide assemblies
guides d’onde
CORRIGENDUM 1
Page 4
...
This May Also Interest You
IEC 60153-4:2022 specifies straight hollow metallic tubing of circular cross section for use as waveguides in electronic equipment. The aim of this document is to specify the hollow metallic waveguides:
a) the details necessary to ensure compatibility and, as far as essential, interchangeability;
b) test methods;
c) uniform requirements for the electrical and mechanical properties
This document is intended to be read in conjunction with IEC 60153-1, which gives general requirements and test methods. This fourth edition cancels and replaces the third edition published in 2017. edition:
a. change of the designation scheme for small circular waveguides (e.g. C 25.5k instead of C 25500);
b. revision of Table 1:
- correction of two waveguide designations (now C 1.2k, C 12k);
- correction of three waveguide diameters (C 140, C 1.4k, C 14k);
- tightening of inner diameter tolerances for waveguides smaller than C 890;
- deletion of waveguide attenuation values for aluminium, gold, and brass;
c. deletion of Table 2 (duplication) and replacement with the table of intermediate waveguide sizes originally envisaged here;
d. addition of an equation for calculating the attenuation of waveguides made of any material.
- Standard29 pagesEnglish and French languagesale 15% off
IEC 61169-1-5:2022 provides test methods for the rise time degradation of radio frequency (RF) connector.
This document is applicable to triaxial and other radio frequency connectors.
- Standard24 pagesEnglish and French languagesale 15% off
IEC 60153-4:2017 specifies straight hollow metallic tubing of circular waveguides for use as waveguides in electronic equipment.
The aim of this recommendation is to specify for hollow metallic waveguides:
a) the details necessary to ensure compatibility and, as far as essential, interchangeability;
b) test methods;
c) uniform requirements for the electrical and mechanical properties.
This edition includes the following significant technical changes with respect to the previous edition:
a) expand and revise the operation frequency range for waveguides;
b) revise the allowance of aperture dimensions;
c) revise the test method for aperture dimensions;
d) revise the equation of attenuation.
- Standard12 pagesEnglish languagesale 15% off
- Standard25 pagesEnglish and French languagesale 15% off
IEC 60154-4:2017 specifies the dimensions of flanges for circular waveguides for use in electronic equipment.
It covers requirements for flanges drilled before or after mounting on waveguides.
The aim of this document is to specify for waveguide flanges the mechanical requirements necessary to ensure compatibility and, as far as practicable, interchangeability as well as to ensure adequate electrical performance.
This edition includes the following significant technical changes with respect to the previous edition:
- revise the estimation for return loss at connection interface of waveguides;
- add two type of waveguide flange for high frequency application, i.e. over 50 GHz;
- expand the operation frequency range up to 3,3 THz;
- rename the frequency band over R1200, i.e. R1.2K.
- Standard33 pagesEnglish and French languagesale 15% off
IEC 60154-2:2016 specifies the dimensions of flanges for ordinary rectangular waveguide for use in electronic equipment. It covers requirements for flanges drilled before or after mounting on waveguides. It should be noted that for optimum electrical performance, post-drilling of the alignment holes after mounting is recommended. The aim of this standard is to specify for waveguide flanges the mechanical requirements necessary to ensure compatibility and, as far as practicable, interchangeability as well as to ensure adequate electrical performance. This edition includes the following significant technical changes with respect to the previous edition:
a) revise the estimation for return loss at connection interface of waveguides;
b) add two type of waveguide flange for high frequency application, i.e. over 50 GHz;
c) expand the operation frequency range up to 3,3 THz;
d) rename the frequency band over R 1200, i.e. R1,2k.
- Standard98 pagesEnglish and French languagesale 15% off
IEC 60153-2:2016 specifies straight hollow metallic tubing of ordinary rectangular waveguide for use as waveguides in electronic equipment. The aim of this standard is to specify for hollow metallic waveguides:
a) the details necessary to ensure compatibility and, as far as essential, interchangeability;
b) test methods;
c) uniform requirements for the electrical and mechanical properties. It should be noted that no recommendations are made for the materials to be used for waveguides. The choice of material is agreed between customer and manufacturer. This document should be read in conjunction with IEC 60153-1, which gives general requirements and test methods. This edition includes the following significant technical changes with respect to the previous edition:
a) expand and revise the operation frequency range for waveguides;
b) revise the allowance of aperture dimensions;
c) revise the test method for aperture dimensions;
d) revise the equation of attenuation.
This publication is to be read in conjunction with IEC 60153-1:2016
- Standard24 pagesEnglish and French languagesale 15% off
IEC 60153-1:2016 specifies straight hollow metallic tubing for use as waveguides in electronic equipment. It covers:
a) the details necessary to ensure compatibility and, as far as essential, interchangeability;
b) test methods;
c) uniform requirements for the electrical and mechanical properties.
It should be noted that no recommendations are made for the materials to be used for waveguides. The choice of material is agreed between customer and manufacturer. This edition includes the following significant technical changes with respect to the previous edition:
a) expand the operation frequency range;
b) revise the equation of attenuation.
This publication is to be read in conjunction with IEC 60154 series .
- Standard28 pagesEnglish and French languagesale 15% off
IEC 60154-1:2016 specifies the dimensions of waveguide flanges for use in electronic equipment. It covers requirements for flanges drilled before or after mounting on waveguides. It should be noted that for optimum electrical performance, post-drilling of the alignment holes after mounting is recommended. The aim of this standard is to specify for waveguide flanges the mechanical requirements necessary to ensure compatibility and, as far as practicable, interchangeability as well as to ensure adequate electrical performance.
- Standard20 pagesEnglish and French languagesale 15% off
- Standard10 pagesEnglish and French languagesale 15% off
Is applicable to attenuation of wavegides and waveguides assemblies. The objective of the given test procedures is to characterize the attenuation. The contents of the corrigendum of July 2006 have been included in this copy.
- Standard21 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.