Field device tool (FDT) interface specification - Part 51-31: Communication implementation for common object model - IEC 61784 CP 3/1 and CP 3/2

IEC TR 62435-51-31:2017(E) provides information for integrating the PROFIBUS protocol into the COM-based implementation of FDT interface specification (IEC TR 62453‑41). This part of IEC 62453 specifies implementation of communication and other services based on IEC 62453‑303-1. This document neither contains the FDT specification nor modifies it.

General Information

Status
Published
Publication Date
14-Jun-2017
Current Stage
PPUB - Publication issued
Start Date
18-May-2017
Completion Date
15-Jun-2017
Ref Project

Relations

Buy Standard

Technical report
IEC TR 62453-51-31:2017 - Field device tool (FDT) interface specification - Part 51-31: Communication implementation for common object model - IEC 61784 CP 3/1 and CP 3/2
English language
43 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


IEC TR 62453-51-31 ®
Edition 1.0 2017-06
TECHNICAL
REPORT
colour
inside
Field device tool (FDT) interface specification –
Part 51-31: Communication implementation for common object model –
IEC 61784 CP 3/1 and CP 3/2
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.

IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished

Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
IEC TR 62453-51-31 ®
Edition 1.0 2017-06
TECHNICAL
REPORT
colour
inside
Field device tool (FDT) interface specification –

Part 51-31: Communication implementation for common object model –

IEC 61784 CP 3/1 and CP 3/2
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 25.040.40; 35.110.05; 35.110 ISBN 978-2-8322-4324-4

– 2 – IEC TR 62453-51-31:2017 © IEC 2017
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, symbols, abbreviated terms and conventions . 7
3.1 Terms and definitions . 7
3.2 Symbols and abbreviated terms . 8
3.3 Conventions . 8
3.3.1 Data type names and references to data types . 8
3.3.2 Vocabulary for requirements . 8
4 Bus category . 8
5 Access to instance and device data . 8
6 Protocol specific behaviour . 8
6.1 General . 8
6.2 Representing modularity . 9
6.2.1 Monolithic DTMs . 9
6.2.2 Composite Device DTMs . 10
6.3 Interfaces and information related to Bus Master Configuration . 13
6.4 Configuration changes in a device . 13
6.5 Error behaviour: DTM refuses new BMCP . 14
7 Protocol specific usage of general data types . 15
8 Network management data types . 15
8.1 General . 15
8.2 PROFIBUS device address . 15
8.3 Master-bus parameter set . 15
8.4 Slave bus parameter set . 15
8.5 Module and channel data . 15
9 Communication data types. 17
9.1 General . 17
9.2 DPV0 communication – FDTProfibusDPV0CommunicationSchema . 18
9.3 DPV1 communication – FDTProfibusDPV1CommunicationSchema . 19
10 Channel parameter data types . 22
11 Device identification . 23
11.1 Device type identification data types – FDTProfibusIdentSchema . 23
11.2 Topology scan data types – DTMProfibusDeviceSchema . 24
11.3 Scan identification data types – FDTProfibusScanIdentSchema . 25
11.4 Device type identification data types – FDTProfibusDeviceIdentSchema . 27
11.5 XSLT Transformation . 29
Annex A (informative) Example documents for a DTM representing a remote I/O . 40
Bibliography . 43

Figure 1 – Part 51-31 of the IEC 62453 series . 6
Figure 2 – Device DTM . 9
Figure 3 – Gateway DTM . 10
Figure 4 – Composite Device DTM . 11

Figure 5 – Modular Gateway DTM . 12
Figure 6 – Interfaces and information related to bus master configuration . 13
Figure 7 – Changes by the user to the configuration of a device in the DTM user
interface . 14
Figure 8 – Error case – DTM refuses the new BMCP from the Frame Application . 14

Table 1 – Protocol specific usage of general data types . 15

– 4 – IEC TR 62453-51-31:2017 © IEC 2017
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIELD DEVICE TOOL (FDT) INTERFACE SPECIFICATION –

Part 51-31: Communication implementation for common object model –
IEC 61784 CP 3/1 and CP 3/2
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
The main task of IEC technical committees is to prepare International Standards. However, a
technical committee may propose the publication of a technical report when it has collected
data of a different kind from that which is normally published as an International Standard, for
example "state of the art".
IEC TR 62453-51-31, which is a echnical report, has been prepared by subcommittee 65E:
Devices and integration in enterprise systems, of IEC technical committee 65: Industrial-
process management, control and automation.
This document cancels and replaces IEC TR 62453-503-1 published in 2009. This edition
constitutes a technical revision. The main changes consist of updates in accordance with
IEC 62453-2 in regard to the description of “Composite Device DTM”.

Each part of the IEC 62453-51-xy series is intended to be read in conjunction with its
corresponding part in the IEC 62453-3xy series. This document corresponds to
IEC 62453-303-1.
The text of this technical report is based on the following documents:
Enquiry draft Report on voting
65E/440/DTR 65E/514/RVC
Full information on the voting for the approval of this technical report can be found in the
report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
The list of all parts of the IEC 62453 series, under the general title Field device tool (FDT)
interface specification, can be found on the IEC website.
The committee has decided that the contents of this document will r
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.