IEC 61290-10-4:2007

Optical amplifiers - Test methods - Part 10-4: Multichannel parameters - Interpolated source subtraction method using an optical spectrum analyzer

This part of IEC 61290 applies to all commercially available optical amplifiers (OAs) and optically amplified subsystems. The object of this standard is to establish uniform requirements for accurate and reliable measurements, by means of the interpolated source subtraction method using an optical spectrum analyzer.

Amplificateurs optiques - Méthodes d'essais - Partie 10-4: Paramètres à canaux multiples - Méthode par soustraction de la source interpolée en utilisant un analyseur de spectre optique

La présente partie de la CEI 61290 s'applique à tous les amplificateurs optiques (AO) et sous-systèmes à amplification optique, disponibles sur le marché. L'objet de la présente norme est d'établir des exigences uniformes afin d'obtenir des mesures précises et fiables, au moyen de la méthode par soustraction de la source interpolée en utilisant un analyseur de spectre optique.

General Information

• Status: Published
• Publication Date: 22-May-2007
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 33.180.30 - Optic amplifiers
• Technical Committee: SC 86C - Fibre optic systems and active devices
• Drafting Committee: WG 3 - TC 86/SC 86C/WG 3
• Current Stage: PPUB - Publication issued
• Start Date: 31-May-2007
• Completion Date: 23-May-2007

Standards Content (Sample)

INTERNATIONAL IEC
STANDARD
CEI
61290-10-4
NORME
First edition
INTERNATIONALE
Première édition
2007-05
Optical amplifiers –
Test methods –
Part 10-4:
Multichannel parameters –
Interpolated source subtraction method
using an optical spectrum analyzer

Amplificateurs optiques –
Méthodes d’essais –
Partie 10-4:
Paramètres à canaux multiples –
Méthode par soustraction de la source interpolée
en utilisant un analyseur de spectre optique
Reference number
Numéro de référence
IEC/CEI 61290-10-4:2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de
référence, texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou
remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: [e-mail]
Tél.: [phone]
Fax: [phone]
INTERNATIONAL IEC
STANDARD
CEI
61290-10-4
NORME
First edition
INTERNATIONALE
Première édition
2007-05
Optical amplifiers –
Test methods –
Part 10-4:
Multichannel parameters –
Interpolated source subtraction method
using an optical spectrum analyzer

Amplificateurs optiques –
Méthodes d’essais –
Partie 10-4:
Paramètres à canaux multiples –
Méthode par soustraction de la source interpolée
en utilisant un analyseur de spectre optique
PRICE CODE
Q
CODE PRIX
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue
Pour prix, voir catalogue en vigueur

– 2 – 61290-10-4 © IEC:2007
CONTENTS
FOREWORD.3
INTRODUCTION.5

1 Scope and object.6
2 Normative references .6
3 Abbreviated terms .7
4 Apparatus.7
5 Test sample.8
6 Procedure .9
6.1 Calibration.9
6.1.1 Calibration of optical bandwidth.9
6.1.2 Calibration of OSA power correction factor .10
6.2 Measurement .11
6.3 Calculation .12
7 Test results .12

Annex A (normative) Limitations of the interpolated source subtraction technique due
to source spontaneous emission .13

Bibliography.17

Figure 1 – Apparatus for gain and noise figure measurement.7
Figure A.1 – DI subtraction error as a function of source spontaneous emission level.14
Figure A.2 – Spectral plot showing additive higher noise level from spontaneous
emission of individual laser sources and broadband multiplexer.16
Figure A.3 – Significantly reduced spontenous emmision using wavelength selective
multiplexer .16

61290-10-4 © IEC:2007 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
OPTICAL AMPLIFIERS –
TEST METHODS –
Part 10-4: Multichannel parameters –
Interpolated source subtraction method using
an optical spectrum analyzer
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61290-10-4 has been prepared by subcommittee 86C: Fibre optic
systems and active devices, of IEC technical committee 86: Fibre optics.
This standard shall be used in conjunction with IEC 61291-1. It was established on the basis
of the second (2006) edition of that standard.
The text of this standard is based on the following documents:
CDV Report on voting
86C/724/CDV 86C/742/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

– 4 – 61290-10-4 © IEC:2007
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61290 series, published under the general title Optical amplifiers –
Test methods, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
61290-10-4 © IEC:2007 – 5 –
INTRODUCTION
This International Standard is devoted to the subject of optical amplifiers. The technology of
optical amplifiers is still rapidly evolving, hence amendments and new additions to this
standard can be expected.
– 6 – 61290-10-4 © IEC:2007
OPTICAL AMPLIFIERS –
TEST METHODS –
Part 10-4: Multichannel parameters –
Interpolated source subtraction method using
an optical spectrum analyzer
1 Scope and object
This part of IEC 61290 applies to all commercially available optical amplifiers (OAs) and
optically amplified subsystems. It applies to OAs using optically pumped fibres (OFAs based
on either rare-earth doped fibres or on the Raman effect), semiconductor optical amplifiers
(SOAs) and waveguides (POWA).
The object of this standard is to establish uniform requirements for accurate and reliable
measurements, by means of the interpolated source subtraction method using an optical
spectrum analyzer. The following OA parameters, as defined in Clause 3 of IEC 61291-1, are
determined:
• channel gain, and
• channel signal-spontaneous noise figure.
This method is called interpolated source subtraction (ISS) because the amplified
spontaneous emission (ASE) at each channel is obtained by interpolating from measurements
at a small wavelength offset around each channel. To minimize the effect of source
spontaneous emission, the effect of source noise is subtracted from the measured noise.
The accuracy of the ISS technique degrades at high input power level due to the spontaneous
emission from the laser source(s). Annex A provides guidance on the limits of this technique
for high input power.
An additional source of inaccuracy is due to interpolation error. Annex A provides guidance on
the magnitude of interpolation error for a typical amplifier ASE versus wavelength
characteristic.
NOTE 1 All numerical values followed by (‡) are suggested values for which the measurement is assured. Other
values may be acceptable but should be verified.
NOTE 2 General aspects of noise figure test methods are reported in IEC 61290-3.
2 Normative references
The following referenced documents are indispensable for the application of this document.
...