IEC 61158-6-19:2010
(Main)Industrial communication networks - Fieldbus specifications - Part 6-19: Application layer protocol specification - Type 19 elements
Industrial communication networks - Fieldbus specifications - Part 6-19: Application layer protocol specification - Type 19 elements
IEC 61158-6-19:2010(E) specifies the protocol of the Type 19 fieldbus application layer, in conformance with the OSI Basic Reference Model (ISO/IEC 7498-1) and the OSI application layer structure (ISO/IEC 9545). It defines the protocol provided to define the wire-representation of the service primitives defined in IEC 61158-5-19:2010, and the externally visible behavior associated with their transfer. This second edition cancels and replaces the first edition published in 2007 and constitutes a technical revision. The main changes with respect to the previous edition are:
- increasing the number of supported devices (511 instead of 254);
- introducing a communication version identification;
- adding a mechanism for remote address allocation;
- introducing enhanced parameter addressing (32 bit instead of 16 bit);
- restructuring control and status word;
- improving the redundancy and hotplug features;
- improving the error handling; adding a multiplexing protocol (SMP: Type 19 Messaging Protocol).
General Information
Relations
Standards Content (Sample)
IEC 61158-6-19 ®
Edition 2.0 2010-08
INTERNATIONAL
STANDARD
Industrial communication networks – Fieldbus specifications –
Part 6-19: Application layer protocol specification – Type 19 elements
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 61158-6-19 ®
Edition 2.0 2010-08
INTERNATIONAL
STANDARD
Industrial communication networks – Fieldbus specifications –
Part 6-19: Application layer protocol specification – Type 19 elements
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
T
ICS 25.04.40; 35.100.70; 35.110 ISBN 978-2-88912-133-5
– 2 – 61158-6-19 © IEC:2010(E)
CONTENTS
FOREWORD.4
INTRODUCTION.6
1 Scope.7
1.1 General .7
1.2 Specifications.8
1.3 Conformance.8
2 Normative references .8
3 Terms, definitions, abbreviations, symbols and conventions .9
3.1 Referenced terms and definitions .9
3.2 Additional terms and definitions.10
3.3 Additional abbreviations and symbols.11
3.4 Conventions .11
4 Abstract syntax.12
5 Transfer syntax .12
5.1 Introduction .12
5.2 RTC PDU merged abstract and transfer syntax .12
6 Structure of FAL protocol state machines .12
7 AP-context state machine.14
7.1 Overview .14
7.2 States .14
7.3 States, events and transitions .14
8 FAL service protocol machine (FSPM).15
8.1 Overview .15
8.2 MGT services .15
8.3 IDN services.16
8.4 CYCIDN services .16
9 Application relationship protocol machine (ARPM).16
9.1 Overview .16
9.2 Master ARPM .17
9.3 Slave ARPM.18
9.4 Primitives received from the FSPM.19
9.5 Indications received from the DMPM .20
10 DLL mapping protocol machine (DMPM).21
10.1 Overview .21
10.2 Primitives received from the ARPM .21
10.3 Indications received from the DL .22
Bibliography.23
Figure 1 – Relationships among protocol machines and adjacent layers .13
Figure 2 – APCSM state diagram .14
Figure 3 – ARPM master AR state diagram .17
Figure 4 – ARPM slave AR state diagram .18
Table 1 – RTC PDU attribute format .12
61158-6-19 © IEC:2010(E) – 3 –
Table 2 – APCSM state-event table .15
Table 3 – Master ARPM state-event table .18
Table 4 – Slave ARPM state-event table .19
Table 5 – ARPM to DL mapping .22
Table 6 – DL to ARPM mapping .22
– 4 – 61158-6-19 © IEC:2010(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
INDUSTRIAL COMMUNICATION NETWORKS –
FIELDBUS SPECIFICATIONS –
Part 6-19: Application layer protocol specification –
Type 19 elements
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
NOTE 1 Use of some of the associated protocol types is restricted by their intellectual-property-right holders. In
all cases, the commitment to limited release of intellectual-property-rights made by the holders of those rights
permits a particular data-link layer protocol type to be used with physical layer and application layer protocols in
Type combinations as specified explicitly in the profile parts. Use of the various protocol types in other
combinations may require permission from their respective intellectual-property-right holders.
International Standard IEC 61158-6-19 has been prepared by subcommittee 65C: Industrial
networks, of IEC technical committee 65: Industrial-process measurement, control and
automation.
This second edition cancels and replaces the first edition published in 2007. This edition
constitutes a technical revision.
The main changes with respect to the previous edition are listed below:
• increasing the number of supported devices (511 instead of 254);
61158-6-19 © IEC:2010(E) – 5 –
• introducing a communication version identification;
• adding a mechanism for remote address allocation;
• introducing enhanced parameter addressing (32 bit instead of 16 bit);
• restructuring control and status word;
• improving the redundancy and hotplug features;
• improving the error handling;
• adding a multiplexing protocol (SMP: Type 19 Messaging Protocol).
The text of this standard is based on the following documents:
FDIS Report on voting
65C/607/FDIS 65C/621/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61158 series, published under the general title Industrial
communication networks – Fieldbus specifications, can be found on the IEC web site.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be:
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
NOTE 2 The revision of this standard will be synchronized with the other parts of the IEC 61158 series.
– 6 – 61158-6-19 © IEC:2010(E)
INTRODUCTION
This part of IEC 61158 is one of a series produced to fa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.