Hexagon head bolts — Product grades A and B

ISO 4014:2011 specifies the characteristics of hexagon head bolts with threads from M1,6 up to and including M64, of product grade A for threads M1,6 to M24 and nominal lengths up to and including 10d or 150 mm, whichever is the shorter, and product grade B for threads over M24 or nominal lengths over 10d or 150 mm, whichever is the shorter.

Vis à tête hexagonale partiellement filetées — Grades A et B

L'ISO 4014:2011 spécifie les caractéristiques des vis à tête hexagonale partiellement filetées de diamètre de filetage M1,6 à M64 inclus, de grade A pour les filetages de diamètre M1,6 à M24 inclus et de longueur nominale inférieure ou égale à 10d ou à 150 mm, la plus petite des deux valeurs étant retenue, et de grade B pour les filetages de diamètre supérieur à M24 ou de longueur nominale supérieure à 10d ou à 150 mm, la plus petite des deux valeurs étant retenue.

General Information

Status
Withdrawn
Publication Date
14-Mar-2011
Current Stage
9599 - Withdrawal of International Standard
Completion Date
28-Jun-2022
Ref Project

Relations

Buy Standard

Standard
ISO 4014:2011 - Hexagon head bolts -- Product grades A and B
English language
14 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 4014:2011 - Vis a tete hexagonale partiellement filetées -- Grades A et B
French language
14 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 4014
Fourth edition
2011-03-15
Hexagon head bolts — Product grades A
and B
Vis à tête hexagonale partiellement filetées — Grades A et B
Reference number
ISO 4014:2011(E)
ISO 2011
---------------------- Page: 1 ----------------------
ISO 4014:2011(E)
PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but

shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In

the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

COPYRIGHT PROTECTED DOCUMENT
© ISO 2011

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 4014:2011(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through ISO

technical committees. Each member body interested in a subject for which a technical committee has been

established has the right to be represented on that committee. International organizations, governmental and

non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the

International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 4014 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 10, Product

standards for fasteners.

This fourth edition cancels and replaces the third edition (ISO 4014:1999), of which it constitutes a minor

revision.
© ISO 2011 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 4014:2011(E)
Introduction

This International Standard belongs to a complete group of product standards developed by ISO on external

hexagon drive fasteners. It comprises the following:
a) hexagon head bolts (ISO 4014, ISO 4015, ISO 4016 and ISO 8765);
b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);

c) hexagon nuts (ISO 4032, ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041, ISO 7042,

ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513);

d) hexagon bolts with flange (ISO 4162, ISO 15071 and ISO 15072);

e) hexagon nuts with flange (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126 and

ISO 21670).
iv © ISO 2011 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 4014:2011(E)
Hexagon head bolts — Product grades A and B
1 Scope

This International Standard specifies the characteristics of hexagon head bolts with threads from M1,6 up to

and including M64, of product grade A for threads M1,6 to M24 and nominal lengths up to and including 10d or

150 mm, whichever is the shorter, and product grade B for threads over M24 or nominal lengths over 10d or

150 mm, whichever is the shorter.

If, in special cases, specifications other than those listed in this International Standard are required, they can

be selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1, ISO 965-1,

ISO 3506-1, ISO 4753 and ISO 4759-1.
2 Normative references

The following referenced documents are indispensable for the application of this document. For dated

references, only the edition cited applies. For undated references, the latest edition of the referenced

document (including any amendments) applies.

ISO 225, Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions

ISO 724, ISO general-purpose metric screw threads — Basic dimensions

ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws

and studs with specified property classes — Coarse thread and fine pitch thread

ISO 965-1, ISO general-purpose metric screw threads — Tolerances — Part 1: Principles and basic data

ISO 3269, Fasteners — Acceptance inspection

ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1: Bolts, screws and

studs
ISO 4017, Hexagon head screws — Product grades A and B
ISO 4042, Fasteners — Electroplated coatings
ISO 4753, Fasteners — Ends of parts with external ISO metric thread

ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C

ISO 6157-1, Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements

ISO 8839, Mechanical properties of fasteners — Bolts, screws, studs and nuts made of non-ferrous metals

ISO 8992, Fasteners — General requirements for bolts, screws, studs and nuts
ISO 10683, Fasteners — Non-electrolytically applied zinc flake coatings
© ISO 2011 – All rights reserved 1
---------------------- Page: 5 ----------------------
ISO 4014:2011(E)
3 Dimensions
See Figure 1 and Tables 1 and 2.
Symbols and descriptions of dimensions are specified in ISO 225.
Dimensions in millimetres
β = 15° to 30°.

Point shall be chamfered or for threads u M4 may be as-rolled (sheared end) in accordance with ISO 4753.

Incomplete thread u u 2P.
Reference datum for d .
Maximum underhead fillet.
Figure 1
2 © ISO 2011 – All rights reserved
---------------------- Page: 6 ----------------------
ISO 4014:2011(E)
© ISO 2011 – All rights reserved 3
Table 1 — Preferred threads
Dimensions in millimetres
Thread, d M1,6 M2 M2,5 M3 M4 M5 M6 M8 M10
P 0,35 0,4 0,45 0,5 0,7 0,8 1 1,25 1,5
9 10 11 12 14 16 18 22 26
b ref. 15 16 17 18 20 22 24 28 32
28 29 30 31 33 35 37 41 45
max. 0,25 0,25 0,25 0,40 0,40 0,50 0,50 0,60 0,60
min. 0,10 0,10 0,10 0,15 0,15 0,15 0,15 0,15 0,15
d max. 2 2,6 3,1 3,6 4,7 5,7 6,8 9,2 11,2
nom. = max. 1,60 2,00 2,50 3,00 4,00 5,00 6,00 8,00 10,00
A 1,46 1,86 2,36 2,86 3,82 4,82 5,82 7,78 9,78
Product grade min.
B 1,35 1,75 2,25 2,75 3,70 4,70 5,70 7,64 9,64
A 2,27 3,07 4,07 4,57 5,88 6,88 8,88 11,63 14,63
d Product grade min.
B 2,30 2,95 3,95 4,45 5,74 6,74 8,74 11,47 14,47
A 3,41 4,32 5,45 6,01 7,66 8,79 11,05 14,38 17,77
e Product grade min.
B 3,28 4,18 5,31 5,88 7,50 8,63 10,89 14,20 17,59
l max. 0,6 0,8 1 1 1,2 1,2 1,4 2 2
nom. 1,1 1,4 1,7 2 2,8 3,5 4 5,3 6,4
max. 1,225 1,525 1,825 2,125 2,925 3,65 4,15 5,45 6,58
Product grade A
k min. 0,975 1,275 1,575 1,875 2,675 3,35 3,85 5,15 6,22
max. 1,3 1,6 1,9 2,2 3,0 3,74 4,24 5,54 6,69
Product grade B
min. 0,9 1,2 1,5 1,8 2,6 3,26 3,76 5,06 6,11
A 0,68 0,89 1,10 1,31 1,87 2,35 2,70 3,61 4,35
k Product grade min.
B 0,63 0,84 1,05 1,26 1,82 2,28 2,63 3,54 4,28
r min. 0,1 0,1 0,1 0,1 0,2 0,2 0,25 0,4 0,4
nom. = max. 3,20 4,00 5,00 5,50 7,00 8,00 10,00 13,00 16,00
A 3,02 3,82 4,82 5,32 6,78 7,78 9,78 12,73 15,73
Product grade min.
B 2,90 3,70 4,70 5,20 6,64 7,64 9,64 12,57 15,57
---------------------- Page: 7 ----------------------
ISO 4014:2011(E)
4 © ISO 2011 – All rights reserved
Table 1 (continued)
Dimensions in millimetres
Thread, d M1,6 M2 M2,5 M3 M4 M5 M6 M8 M10
Product grade
l and l
s g
A B
l l l l l l l l l l l l l l l l l l l
s g s g s g s g s g s g s g s g s g

nom. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.

12 11,65 12,35 — — 1,2 3

16 15,65 16,35 — — 5,2 7 4 6 2,75 5 For sizes above the solid, bold, stepped line, ISO 4017 is recommended.

20 19,58 20,42 18,95 21,05 8 10 6,75 9 5,5 8
25 24,58 25,42 23,95 26,05 11,75 14 10,5 13 7,5 11 5 9
30 29,58 30,42 28,95 31,05 15,5 18 12,5 16 10 14 7 12
35 34,5 35,5 33,75 36,25 17,5 21 15 19 12 17
40 39,5 40,5 38,75 41,25 22,5 26 20 24 17 22 11,75 18
45 44,5 45,5 43,75 46,25 25 29 22 27 16,75 23 11,5 19
50 49,5 50,5 48,75 51,25 30 34 27 32 21,75 28 16,5 24
55 54,4 55,6 53,5 56,5 32 37 26,75 33 21,5 29
60 59,4 60,6 58,5 61,5 37 42 31,75 38 26,5 34
65 64,4 65,6 63,5 66,5 36,75 43 31,5 39
70 69,4 70,6 68,5 71,5 41,75 48 36,5 44
80 79,4 80,6 78,5 81,5 51,75 58 46,5 54
90 89,3 90,7 88,25 91,75 56,5 64
100 99,3 100,7 98,25 101,75 66,5 74
110 109,3 110,7 108,25 111,75
120 119,3 120,7 118,25 121,75
---------------------- Page: 8 ----------------------
ISO 4014:2011(E)
© ISO 2011 – All rights reserved 5
Table 1 (continued)
Dimensions in millimetres
Thread, d M12 M16 M20 M24 M30 M36 M42 M48 M56 M64
P 1,75 2 2,5 3 3,5 4 4,5 5 5,5 6
30 38 46 54 66 — — — — —
b ref. 36 44 52 60 72 84 96 108 — —
49 57 65 73 85 97 109 121 137 153
max. 0,60 0,8 0,8 0,8 0,8 0,8 1,0 1,0 1,0 1,0
min. 0,15 0,2 0,2 0,2 0,2 0,2 0,3 0,3 0,3 0,3
d max. 13,7 17,7 22,4 26,4 33,4 39,4 45,6 52,6 63 71
nom. = max. 12,00 16,00 20,00 24,00 30,00 36,00 42,00 48,00 56,00 64,00
A 11,73 15,73 19,67 23,67 — — — — — —
Product grade min.
B 11,57 15,57 19,48 23,48 29,48 35,38 41,38 47,38 55,26 63,26
A 16,63 22,49 28,19 33,61 — — — — — —
d Product grade min.
B 16,47 22 27,7 33,25 42,75 51,11 59,95 69,45 78,66 88,16
A 20,03 26,75 33,53 39,98 — — — — — —
e Product grade min.
B 19,85 26,17 32,95 39,55 50,85 60,79 71,3 82,6 93,56 104,86
l max. 3 3 4 4 6 6 8 10 12 13
nom. 7,5 10 12,5 15 18,7 22,5 26 30 35 40
max. 7,68 10,18 12,715 15,215 — — — — — —
Product grade A
k min. 7,32 9,82 12,285 14,785 — — — — — —
max. 7,79 10,29 12,85 15,35 19,12 22,92 26,42 30,42 35,5 40,5
Product grade B
min. 7,21 9,71 12,15 14,65 18,28 22,08 25,58 29,58 34,5 39,5
A 5,12 6,87 8,6 10,35 — — — — — —
k Product grade min.
B 5,05 6,8 8,51 10,26 12,8 15,46 17,91 20,71 24,15 27,65
r min. 0,6 0,6 0,8 0,8 1 1 1,2 1,6 2 2
nom. = max. 18,00 24,00 30,00 36,00 46 55,0 65,0 75,0 85,0 95,0
A 17,73 23,67 29,67 35,38 — — — — — —
Product grade min.
B 17,57 23,16 29,16 35,00 45 53,8 63,1 73,1 82,8 92,8
---------------------- Page: 9 ----------------------
ISO 4014:2011(E)
6 © ISO 2011 – All rights reserved
Table 1 (continued)
Dimensions in millimetres
Thread, d M12 M16 M20 M24 M30 M36 M42 M48 M56 M64
Product grade
l and l
s g
A B
l l l l l l l l l l l l l l l l l l l l l
s g s g s g s g s g s g s g s g s g s g

nom. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.

50 49,5 50,5 — — 11,2520
55 54,4 55,6 53,5 56,5 16,2525
60 59,4 60,6 58,5 61,5 21,2530
65 64,4 65,6 63,5 66,5 26,2535 17 27
70 69,4 70,6 68,5 71,5 31,2540 22 32
80 79,4 80,6 78,5 81,5 41,2550 32 42 21,5 34
90 89,3 90,7 88,25 91,75 51,2560 42 52 31,5 44 21 36
100 99,3 100,7 98,25 101,75 61,2570 52 62 41,5 54 31 46
110 109,3 110,7 108,25 111,75 71,2580 62 72 51,5 64 41 56 26,5 44
120 119,3 120,7 118,25 121,75 81,2590 72 82 61,5 74 51 66 36,5 54
130 129,2 130,8 128 132 76 86 65,5 78 55 70 40,5 58
140 139,2 140,8 138 142 86 96 75,5 88 65 80 50,5 68 36 56
150 149,2 150,8 148 152 96 106 85,5 98 75 90 60,5 78 46 66
160 — — 158 162 106 116 95,5 108 85 100 70,5 88 56 76 41,5 64
180 — — 178 182 115,5128 105 120 90,5 108 76 96 61,5 84 47 72
200 — — 197,7 202,3 135,5148 125 140 110,5 128 96 116 81,5 104 67 92
220 — — 217,7 222,3 132 147 117,5 135 103 123 88,5 111 74 99 55,5 83
240 — — 237,7 242,3 152 167 137,5 155 123 143 108,5131 94 119 75,5 103
260 — — 257,4 262,6 157,5 175 143 163 128,5151 114 139 95,5 123 77 107
280 — — 277,4 282,6 177,5 195 163 183 148,5171 134 159 115,5143 97 127
300 — — 297,4 302,6 197,5 215 183 203 168,5191 154 179 135,5163 117 147
320 — — 317,15 322,85 203 223 188,5211 174 199 155,5183 137 167
340 — — 337,15 342,85 233 243 208,5231 194 219 175,5203 157 187
---------------------- Page: 10 ----------------------
ISO 4014:2011(E)
© ISO 2011 – All rights reserved 7
Table 1 (continued)
Dimensions in
...

NORME ISO
INTERNATIONALE 4014
Quatrième édition
2011-03-15
Vis à tête hexagonale partiellement
filetées — Grades A et B
Hexagon head bolts — Product grades A and B
Numéro de référence
ISO 4014:2011(F)
ISO 2011
---------------------- Page: 1 ----------------------
ISO 4014:2011(F)
PDF – Exonération de responsabilité

Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier

peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence

autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées

acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute

responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.

Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info

du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir

l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,

veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2011

Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous

quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit

de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.

ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2011 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 4014:2011(F)
Avant-propos

L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de

normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée

aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du

comité technique créé à cet effet. Les organisations internationales, gouvernementales et non

gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec

la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.

Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,

Partie 2.

La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes

internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur

publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres

votants.

L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de

droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne

pas avoir identifié de tels droits de propriété et averti de leur existence.

L'ISO 4014 a été élaborée par le comité technique ISO/TC 2, Éléments de fixation, sous-comité SC 10,

Normes de produits pour éléments de fixation.

Cette quatrième édition annule et remplace la troisième édition (ISO 4014:1999), dont elle constitue une

révision mineure.
© ISO 2011 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 4014:2011(F)
Introduction

La présente Norme internationale fait partie de la série complète des normes de produit ISO traitant des

éléments de fixation à entraînement hexagonal. La série comprend:

a) les vis à tête hexagonale partiellement filetées (ISO 4014, ISO 4015, ISO 4016 et ISO 8765);

b) les vis à tête hexagonale entièrement filetées (ISO 4017, ISO 4018 et ISO 8676);

c) les écrous hexagonaux (ISO 4032, ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041,

ISO 7042, ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 et ISO 10513);

d) les vis à tête hexagonale à embase (ISO 4162, ISO 15071 et ISO 15072);

e) les écrous hexagonaux à embase (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126 et

ISO 21670).
iv © ISO 2011 – Tous droits réservés
---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 4014:2011(F)
Vis à tête hexagonale partiellement filetées — Grades A et B
1 Domaine d'application

La présente Norme internationale spécifie les caractéristiques des vis à tête hexagonale partiellement filetées

de diamètre de filetage M1,6 à M64 inclus, de grade A pour les filetages de diamètre M1,6 à M24 inclus et de

longueur nominale inférieure ou égale à 10d ou à 150 mm, la plus petite des deux valeurs étant retenue, et de

grade B pour les filetages de diamètre supérieur à M24 ou de longueur nominale supérieure à 10d ou à

150 mm, la plus petite des deux valeurs étant retenue.

Si, dans des cas particuliers, des spécifications autres que celles figurant dans la présente Norme

internationale sont requises, elles peuvent être prises dans les Normes internationales existantes, par

exemple l'ISO 724, l'ISO 888, l'ISO 898-1, l'ISO 965-1, l'ISO 3506-1, l'ISO 4753 et l'ISO 4759-1.

2 Références normatives

Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les

références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du

document de référence s'applique (y compris les éventuels amendements).

ISO 225, Éléments de fixation — Vis, goujons et écrous — Symboles et description des dimensions

ISO 724, Filetages métriques ISO pour usages généraux — Dimensions de base

ISO 898-1, Caractéristiques mécaniques des éléments de fixation en acier au carbone et en acier allié —

Partie 1: Vis, goujons et tiges filetées de classes de qualités spécifiées — Filetages à pas gros et filetages à

pas fin

ISO 965-1, Filetages métriques ISO pour usages généraux — Tolérances — Partie 1: Principes et données

fondamentales
ISO 3269, Éléments de fixation — Contrôle de réception

ISO 3506-1, Caractéristiques mécaniques des éléments de fixation en acier inoxydable résistant à la

corrosion — Partie 1: Vis et goujons
ISO 4017, Vis à tête hexagonale entièrement filetées — Grades A et B
ISO 4042, Éléments de fixation — Revêtements électrolytiques

ISO 4753, Éléments de fixation — Extrémités des éléments à filetage extérieur métrique ISO

ISO 4759-1, Tolérances pour éléments de fixation — Partie 1: Vis, goujons et écrous — Grades A, B et C

ISO 6157-1, Éléments de fixation — Défauts de surface — Partie 1: Vis et goujons d'usage général

ISO 8839, Caractéristiques mécaniques des éléments de fixation — Vis, goujons et écrous en métaux non

ferreux
ISO 8992, Éléments de fixation — Exigences générales pour vis, goujons et écrous

ISO 10683, Éléments de fixation — Revêtements non électrolytiques de lamelles de zinc

© ISO 2011 – Tous droits réservés 1
---------------------- Page: 5 ----------------------
ISO 4014:2011(F)
3 Dimensions
Voir Figure 1 et Tableaux 1 et 2.
Les symboles et la description des dimensions sont spécifiés dans l'ISO 225.
Dimensions en millimètres
β = 15° à 30°.

Le bout doit être chanfreiné ou, pour les vis partiellement filetées de filetage u M4, l'extrémité peut être brute de

roulage conformément à l'ISO 4753.
Filetage incomplet u u 2P.
Axe de référence pour d .
Raccordement sous tête maximal.
Figure 1
2 © ISO 2011 – Tous droits réservés
---------------------- Page: 6 ----------------------
ISO 4014:2011(F)
© ISO 2011 – Tous droits réservés 3
Tableau 1 — Filetages préférentiels
Dimensions en millimètres
Filetage, d M1,6 M2 M2,5 M3 M4 M5 M6 M8 M10
P 0,35 0,4 0,45 0,5 0,7 0,8 1 1,25 1,5
9 10 11 12 14 16 18 22 26
b réf. 15 16 17 18 20 22 24 28 32
28 29 30 31 33 35 37 41 45
max. 0,25 0,25 0,25 0,40 0,40 0,50 0,50 0,60 0,60
min. 0,10 0,10 0,10 0,15 0,15 0,15 0,15 0,15 0,15
d max. 2 2,6 3,1 3,6 4,7 5,7 6,8 9,2 11,2
nom. = max. 1,60 2,00 2,50 3,00 4,00 5,00 6,00 8,00 10,00
A 1,46 1,86 2,36 2,86 3,82 4,82 5,82 7,78 9,78
Grade min.
B 1,35 1,75 2,25 2,75 3,70 4,70 5,70 7,64 9,64
A 2,27 3,07 4,07 4,57 5,88 6,88 8,88 11,63 14,63
d Grade min.
B 2,30 2,95 3,95 4,45 5,74 6,74 8,74 11,47 14,47
A 3,41 4,32 5,45 6,01 7,66 8,79 11,05 14,38 17,77
e Grade min.
B 3,28 4,18 5,31 5,88 7,50 8,63 10,89 14,20 17,59
l max. 0,6 0,8 1 1 1,2 1,2 1,4 2 2
nom. 1,1 1,4 1,7 2 2,8 3,5 4 5,3 6,4
max. 1,225 1,525 1,825 2,125 2,925 3,65 4,15 5,45 6,58
Grade A
k min. 0,975 1,275 1,575 1,875 2,675 3,35 3,85 5,15 6,22
max. 1,3 1,6 1,9 2,2 3,0 3,74 4,24 5,54 6,69
Grade B
min. 0,9 1,2 1,5 1,8 2,6 3,26 3,76 5,06 6,11
A 0,68 0,89 1,10 1,31 1,87 2,35 2,70 3,61 4,35
k Grade min.
B 0,63 0,84 1,05 1,26 1,82 2,28 2,63 3,54 4,28
r min. 0,1 0,1 0,1 0,1 0,2 0,2 0,25 0,4 0,4
nom. = max. 3,20 4,00 5,00 5,50 7,00 8,00 10,00 13,00 16,00
A 3,02 3,82 4,82 5,32 6,78 7,78 9,78 12,73 15,73
Grade min.
B 2,90 3,70 4,70 5,20 6,64 7,64 9,64 12,57 15,57
---------------------- Page: 7 ----------------------
ISO 4014:2011(F)
4 © ISO 2011 – Tous droits réservés
Tableau 1 (suite)
Dimensions en millimètres
Filetage, d M1,6 M2 M2,5 M3 M4 M5 M6 M8 M10
Grade
l et l
s g
A B
l l l l l l l l l l l l l l l l l l l
s g s g s g s g s g s g s g s g s g

nom. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.

12 11,65 12,35 — — 1,2 3
16 15,65 16,35 — — 5,2 7 4 6 2,75 5
Pour les dimensions se trouvant au-dessus de la ligne
en traits continus forts, l'ISO 4017 est recommandée.
20 19,58 20,42 18,95 21,05 8 10 6,75 9 5,5 8
25 24,58 25,42 23,95 26,05 11,75 14 10,5 13 7,5 11 5 9
30 29,58 30,42 28,95 31,05 15,5 18 12,5 16 10 14 7 12
35 34,5 35,5 33,75 36,25 17,5 21 15 19 12 17
40 39,5 40,5 38,75 41,25 22,5 26 20 24 17 22 11,75 18
45 44,5 45,5 43,75 46,25 25 29 22 27 16,75 23 11,5 19
50 49,5 50,5 48,75 51,25 30 34 27 32 21,75 28 16,5 24
55 54,4 55,6 53,5 56,5 32 37 26,75 33 21,5 29
60 59,4 60,6 58,5 61,5 37 42 31,75 38 26,5 34
65 64,4 65,6 63,5 66,5 36,75 43 31,5 39
70 69,4 70,6 68,5 71,5 41,75 48 36,5 44
80 79,4 80,6 78,5 81,5 51,75 58 46,5 54
90 89,3 90,7 88,25 91,75 56,5 64
100 99,3 100,7 98,25 101,75 66,5 74
110 109,3 110,7 108,25 111,75
120 119,3 120,7 118,25 121,75
---------------------- Page: 8 ----------------------
ISO 4014:2011(F)
© ISO 2011 – Tous droits réservés 5
Tableau 1 (suite)
Dimensions en millimètres
Filetage, d M12 M16 M20 M24 M30 M36 M42 M48 M56 M64
P 1,75 2 2,5 3 3,5 4 4,5 5 5,5 6
30 38 46 54 66 — — — — —
b réf. 36 44 52 60 72 84 96 108 — —
49 57 65 73 85 97 109 121 137 153
max. 0,60 0,8 0,8 0,8 0,8 0,8 1,0 1,0 1,0 1,0
min. 0,15 0,2 0,2 0,2 0,2 0,2 0,3 0,3 0,3 0,3
d max. 13,7 17,7 22,4 26,4 33,4 39,4 45,6 52,6 63 71
nom. = max. 12,00 16,00 20,00 24,00 30,00 36,00 42,00 48,00 56,00 64,00
A 11,73 15,73 19,67 23,67 — — — — — —
Grade min.
B 11,57 15,57 19,48 23,48 29,48 35,38 41,38 47,38 55,26 63,26
A 16,63 22,49 28,19 33,61 — — — — — —
d Grade min.
B 16,47 22 27,7 33,25 42,75 51,11 59,95 69,45 78,66 88,16
A 20,03 26,75 33,53 39,98 — — — — — —
e Grade min.
B 19,85 26,17 32,95 39,55 50,85 60,79 71,3 82,6 93,56 104,86
l max. 3 3 4 4 6 6 8 10 12 13
nom. 7,5 10 12,5 15 18,7 22,5 26 30 35 40
max. 7,68 10,18 12,715 15,215 — — — — — —
Grade A
k min. 7,32 9,82 12,285 14,785 — — — — — —
max. 7,79 10,29 12,85 15,35 19,12 22,92 26,42 30,42 35,5 40,5
Grade B
min. 7,21 9,71 12,15 14,65 18,28 22,08 25,58 29,58 34,5 39,5
A 5,12 6,87 8,6 10,35 — — — — — —
k Grade min.
B 5,05 6,8 8,51 10,26 12,8 15,46 17,91 20,71 24,15 27,65
r min. 0,6 0,6 0,8 0,8 1 1 1,2 1,6 2 2
nom. = max. 18,00 24,00 30,00 36,00 46 55,0 65,0 75,0 85,0 95,0
A 17,73 23,67 29,67 35,38 — — — — — —
Grade min.
B 17,57 23,16 29,16 35,00 45 53,8 63,1 73,1 82,8 92,8
---------------------- Page: 9 ----------------------
ISO 4014:2011(F)
6 © ISO 2011 – Tous droits réservés
Tableau 1 (suite)
Dimensions en millimètres
Filetage, d M12 M16 M20 M24 M30 M36 M42 M48 M56 M64
Grade
l et l
s g
A B
l l l l l l l l l l l l l l l l l l l l l
s g s g s g s g s g s g s g s g s g s g

nom. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.

50 49,5 50,5 — — 11,2520
55 54,4 55,6 53,5 56,5 16,2525
60 59,4 60,6 58,5 61,5 21,2530
65 64,4 65,6 63,5 66,5 26,2535 17 27
70 69,4 70,6 68,5 71,5 31,2540 22 32
80 79,4 80,6 78,5 81,5 41,2550 32 42 21,5 34
90 89,3 90,7 88,25 91,75 51,2560 42 52 31,5 44 21 36
100 99,3 100,7 98,25 101,75 61,2570 52 62 41,5 54 31 46
110 109,3 110,7 108,25 111,75 71,2580 62 72 51,5 64 41 56 26,5 44
120 119,3 120,7 118,25 121,75 81,2590 72 82 61,5 74 51 66 36,5 54
130 129,2 130,8 128 132 76 86 65,5 78 55 70 40,5 58
140 139,2 140,8 138 142 86 96 75,5 88 65 80 50,5 68 36 56
150 149,2 150,8 148 152 96 106 85,5 98 75 90 60,5 78 46 66
160 — — 158 162 106 116 95,5 108 85 100 70,5 88 56 76 41,5 64
180 — — 178 182 115,5128 105 120 90,5 108 76 96 61,5 84 47 72
200 — — 197,7 202,3 135,5148 125 140 110,5 128 96 116 81,5 104 67 92
220 — — 217,7 222,3 132 147 117,5 135 103 123 88,5 111 74 99 55,5 83
240 — — 237,7 242,3 152 167 137,5 155 123 143 108,5131 94 119 75,5 103
260 — — 257,4 262,6 157,5 175 143 163 128,5151 114 139 95,5 123 77 107
280 — — 277,4 282,6 177,5 195 163 183 148,5171 134 159 115,5143 97 127
300 — — 297,4 302,6 197,5 215 183 203 168,5191 154 179 135,5163 117 147
320 — — 317,15 322,85
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.