ISO 5694:2023

Ships and marine technology — Deck covering

This document provides requirements for production, use and inspection of deck coverings for shipbuilding. This document is applicable to deck coverings (underlay, cement type). It is not applicable to overlay floor coverings such as ceramic tile, carpet and rubber sheet.

Navires et technologie maritime — Revêtement de pont

General Information

• Status: Published
• Publication Date: 30-Jul-2023
• ICS: 47.020.50 - Deck equipment and installations
• Technical Committee: ISO/TC 8/SC 8 - Ship design
• Drafting Committee: ISO/TC 8/SC 8 - Ship design
• Current Stage: 6060 - International Standard published
• Start Date: 31-Jul-2023
• Due Date: 14-Dec-2023
• Completion Date: 31-Jul-2023

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 5694
First edition
2023-07
Ships and marine technology — Deck
covering
Navires et technologie maritime — Revêtement de pont
Reference number
ISO 5694:2023(E)
© ISO 2023

---------------------- Page: 1 ----------------------
ISO 5694:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 5694:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification and construction . 2
4.1 Classification . 2
4.2 Construction . 2
4.3 Materials . 2
5 Requirements . 2
6 Test methods . 3
6.1 Sample preparation . 3
6.2 Density . 3
6.3 Flexural strength. 3
6.4 Compressive strength . 4
6.5 Initial setting time and final coagulation time . 4
6.6 Water absorption rate . 4
6.7 Oil absorption rate . 4
6.8 Thermal conductivity . 4
6.9 Impact resistance . 4
6.10 Vibration resistance . . 4
6.11 Asbestos-free requirement . . 4
6.12 Organic matter content . 4
6.13 Not readily ignitable . 4
6.14 Low sowing flame . 4
6.15 Smoke and toxicity . 5
6.16 Non-combustibility . 5
6.17 Fire resistance . 5
6.18 Sound insulation index . 5
7 Marking . . 5
Annex A (informative) Examples of deck construction consisting of deck covering .6
iii
© ISO 2023 – All rights reserved

---------------------- Page: 3 ----------------------
ISO 5694:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 8, Ships and marine technology,
Subcommittee SC 8, Ship design.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
  © ISO 2023 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 5694:2023(E)
Introduction
Deck covering is a covering layer which is laid on the surface of a ship's steel deck with properties such
as thermal resistance, fire resistance, vibration resistance, noise insulation and anti-skid.
In order to meet the requirements of IMO SOLAS, the decks of different spaces of ships should have
certain requirements for fire-resisting division class. These requirements apply to laying deck covering.
The fire resistance capability is examined in a fire test specified in International Code for Application
of Fire Test procedure (IMO
...