Paints and varnishes — Determination of solvents in water-thinnable coating materials — Gas-chromatographic method

This document specifies a method for the gas-chromatographic determination of the solvents in water-thinnable paints and varnishes, binder solutions, emulsions and dispersions. With the precision stated in Clause 13, single components above 0,02 % (mass fraction) can be determined quantitatively. The method defined in this document is not applicable for the determination of Volatile Organic Compounds (VOC) and Semi-Volatile Organic Compounds (SVOC) content. NOTE For the determination of VOC and SVOC, see ISO 11890‑2[2].

Peintures et vernis — Détermination des solvants dans des peintures diluables à l'eau — Méthode par chromatographie en phase gazeuse

Le présent document spécifie une méthode de détermination par chromatographie en phase gazeuse des solvants présents dans les solutions de liant, les émulsions, les dispersions, ainsi que les peintures et vernis diluables à l'eau. Avec la fidélité indiquée à l'Article 13, il est possible de déterminer de manière quantitative les constituants d'une concentration supérieure à 0,02 % (en fraction massique). La méthode définie dans le présent document ne s'applique pas à la mesure de la teneur en composés organiques volatils (COV) et en composés organiques semi‑volatils (COSV). NOTE Pour la quantification des COV et des COSV, voir l'ISO 11890‑2[2].

General Information

Status
Published
Publication Date
11-Jul-2019
Current Stage
6060 - International Standard published
Start Date
18-Jun-2019
Due Date
23-May-2020
Completion Date
12-Jul-2019
Ref Project

Buy Standard

Standard
ISO 22518:2019 - Paints and varnishes -- Determination of solvents in water-thinnable coating materials -- Gas-chromatographic method
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 22518:2019 - Peintures et vernis -- Détermination des solvants dans des peintures diluables à l'eau -- Méthode par chromatographie en phase gazeuse
French language
13 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 22518
First edition
2019-07
Paints and varnishes —
Determination of solvents in water-
thinnable coating materials — Gas-
chromatographic method
Peintures et vernis — Détermination des solvants dans des peintures
diluable à l'eau — Méthode par chromatographie en phase gazeuse
Reference number
ISO 22518:2019(E)
ISO 2019
---------------------- Page: 1 ----------------------
ISO 22518:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 22518:2019(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Units ................................................................................................................................................................................................................................... 1

5 Principle ........................................................................................................................................................................................................................ 1

6 Apparatus ..................................................................................................................................................................................................................... 2

6.1 Gas chromatograph ............................................................................................................................................................................. 2

6.1.1 General...................................................................................................................................................................................... 2

6.1.2 Sample injection system ............................................................................................................................................ 2

6.1.3 Oven ............................................................................................................................................................................................ 2

6.1.4 Detector ................................................................................................................................................................................... 2

6.1.5 Capillary separation column .................................................................................................................................. 3

6.1.6 Injection syringe............................................................................................................................................................... 3

6.2 Data acquisition ..................................................................................................................................................................................... 3

6.3 Sample vessel ........................................................................................................................................................................................... 3

7 Reagents ........................................................................................................................................................................................................................ 3

7.1 Gases ................................................................................................................................................................................................................ 3

7.2 Internal standard .................................................................................................................................................................................. 3

7.3 Calibration substances ..................................................................................................................................................................... 3

7.4 Diluents ......................................................................................................................................................................................................... 3

8 Sampling ........................................................................................................................................................................................................................ 4

9 Choice of sample injection system ..................................................................................................................................................... 4

10 Procedure..................................................................................................................................................................................................................... 4

10.1 Gas chromatographic conditions ............................................................................................................................................. 4

10.1.1 General...................................................................................................................................................................................... 4

10.1.2 Example of hot injection and gas chromatography of a water-thinnable

coating material ................................................................................................................................................................ 4

10.1.3 Cold injection and gas chromatography of a water-thinnable coating

material (example) ........................................................................................................................................... .............. 6

10.2 Injection volume .................................................................................................................................................................................... 7

10.3 Calibration .................................................................................................................................................................................................. 7

10.4 Sample preparation and analysis ............................................................................................................................................ 7

11 Expression of results ........................................................................................................................................................................................ 8

12 Precision ....................................................................................................................................................................................................................... 8

12.1 General ........................................................................................................................................................................................................... 8

12.2 Repeatability ............................................................................................................................................................................................. 9

12.3 Reproducibility ....................................................................................................................................................................................... 9

13 Test report ................................................................................................................................................................................................................... 9

Bibliography .............................................................................................................................................................................................................................11

© ISO 2019 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 22518:2019(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso

.org/iso/foreword .html.

This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee

SC 9, General test methods for paints and varnishes.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 22518:2019(E)
Paints and varnishes — Determination of solvents
in water-thinnable coating materials — Gas-
chromatographic method
1 Scope

This document specifies a method for the gas-chromatographic determination of the solvents in water-

thinnable paints and varnishes, binder solutions, emulsions and dispersions.

With the precision stated in Clause 13, single components above 0,02 % (mass fraction) can be

determined quantitatively.

The method defined in this document is not applicable for the determination of Volatile Organic

Compounds (VOC) and Semi-Volatile Organic Compounds (SVOC) content.
[2]
NOTE For the determination of VOC and SVOC, see ISO 11890-2 .
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 4618, Paints and varnishes — Terms and definitions

ISO 15528, Paints, varnishes and raw materials for paints and varnishes — Sampling

3 Terms and definitions

For the purposes of this document, the terms and definitions given in ISO 4618 apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
4 Units
The analytical results are expressed as a percentage mass fraction.
5 Principle

After sample preparation, the components contained in the sample under test are separated by gas

chromatography. Either a hot or a cold sample injection system can be used, depending on the product

type. After the components have been identified, they are quantified from the peak areas using the

internal standard method.
© ISO 2019 – All rights reserved 1
---------------------- Page: 5 ----------------------
ISO 22518:2019(E)
6 Apparatus
6.1 Gas chromatograph
6.1.1 General

The gas chromatograph shall be suitable for use with capillary separation columns and meet the

conditions specified in 6.1.2 to 6.1.4.

All of the instrumental parts coming into contact with the test sample shall be made of a material, e.g.

glass, which is resistant to the sample and which will not change it chemically.
6.1.2 Sample injection system
6.1.2.1 Hot injection system

The instrument shall have a variable-temperature injection block with a sample splitter. The injection

temperature shall be capable of being set to an accuracy of 1 K. The split ratio shall be adjustable and

capable of being monitored. The sample splitter insert shall contain silanized glass wool to retain

non-volatile constituents. It shall be cleaned and provided with new glass wool packing or replaced

as required to rule out errors due to residues of binder or pigment (e.g. adsorption of solvents). The

occurrence of adsorption is revealed by peak tailing, in particular with components of low volatility.

6.1.2.2 Cold injection system

The cold injection system shall be provided with temperature programming for heating from room

temperature to 300 °C and shall have a sample splitter inlet made of a material such as glass. It shall be

provided with a silanized glass wool packing and shall be
...

NORME ISO
INTERNATIONALE 22518
Première édition
2019-07
Peintures et vernis — Détermination
des solvants dans des peintures
diluables à l'eau — Méthode par
chromatographie en phase gazeuse
Paints and varnishes — Determination of solvents in water-thinnable
coating materials — Gas-chromatographic method
Numéro de référence
ISO 22518:2019(F)
ISO 2019
---------------------- Page: 1 ----------------------
ISO 22518:2019(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2019

Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette

publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,

y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut

être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.

ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2019 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 22518:2019(F)
Sommaire Page

Avant‑propos ..............................................................................................................................................................................................................................iv

1 Domaine d’application ................................................................................................................................................................................... 1

2 Références normatives ................................................................................................................................................................................... 1

3 Termes et définitions ....................................................................................................................................................................................... 1

4 Unités ................................................................................................................................................................................................................................ 1

5 Principe .......................................................................................................................................................................................................................... 1

6 Appareillage .............................................................................................................................................................................................................. 2

6.1 Chromatographe en phase gazeuse ...................................................................................................................................... 2

6.1.1 Généralités ............................................................................................................................................................................ 2

6.1.2 Système d’injection des échantillons ............................................................................................................. 2

6.1.3 Four ............................................................................................................................................................................................. 2

6.1.4 Détecteur ................................................................................................................................................................................ 2

6.1.5 Colonne de séparation capillaire ....................................................................................................................... 3

6.1.6 Seringue d’injection....................................................................................................................................................... 3

6.2 Acquisition des données ................................................................................................................................................................. 3

6.3 Récipient pour échantillon ........................................................................................................................................................... 3

7 Réactifs ........................................................................................................................................................................................................................... 3

7.1 Gaz ..................................................................................................................................................................................................................... 3

7.2 Étalon interne .......................................................................................................................................................................................... 3

7.3 Substances d’étalonnage ................................................................................................................................................................ 4

7.4 Diluants ......................................................................................................................................................................................................... 4

8 Échantillonnage ..................................................................................................................................................................................................... 4

9 Choix du système d’injection des échantillons ..................................................................................................................... 4

10 Mode opératoire.................................................................................................................................................................................................... 4

10.1 Conditions de la chromatographie en phase gazeuse ........................................................................................... 4

10.1.1 Généralités ............................................................................................................................................................................ 4

10.1.2 Exemple de chromatographie en phase gazeuse avec injection à chaud

d’un produit de peinture diluable à l’eau ................................................................................................... 4

10.1.3 Chromatographie en phase gazeuse avec injection à froid d’un produit de

peinture diluable à l’eau (exemple) ................................................................................................................. 6

10.2 Volume d’injection ............................................................................................................................................................................... 7

10.3 Étalonnage .................................................................................................................................................................................................. 7

10.4 Préparation et analyse des échantillons ........................................................................................................................... 8

11 Expression des résultats............................................................................................................................................................................... 8

12 Fidélité ............................................................................................................................................................................................................................ 8

12.1 Généralités .................................................................................................................................................................................................. 8

12.2 Répétabilité ................................................................................................................................................................................................ 9

12.3 Reproductibilité ..................................................................................................................................................................................10

13 Rapport d’essai ....................................................................................................................................................................................................10

Bibliographie ...........................................................................................................................................................................................................................11

© ISO 2019 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 22518:2019(F)
Avant‑propos

L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes

nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est

en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude

a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,

gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.

L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui

concerne la normalisation électrotechnique.

Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont

décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents

critères d’approbation requis pour les différents types de documents ISO. Le présent document a été

rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www

.iso .org/ directives).

L’attention est attirée sur le fait que certains des éléments du présent document peuvent faire l’objet de

droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable

de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant

les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de

l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de

brevets reçues par l’ISO (voir www .iso .org/ brevets).

Les appellations commerciales éventuellement mentionnées dans le présent document sont données

pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un

engagement.

Pour une explication de la nature volontaire des normes, la signification des termes et expressions

spécifiques de l’ISO liés à l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion

de l’ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles

techniques au commerce (OTC), voir www .iso .org/ avant -propos.

Le présent document a été élaboré par le comité technique ISO/TC 35, Peintures et vernis, sous-comité

SC 9, Méthodes générales d'essais des peintures et vernis.

Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent

document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes

se trouve à l’adresse www .iso .org/ fr/ members .html.
iv © ISO 2019 – Tous droits réservés
---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 22518:2019(F)
Peintures et vernis — Détermination des solvants
dans des peintures diluables à l'eau — Méthode par
chromatographie en phase gazeuse
1 Domaine d’application

Le présent document spécifie une méthode de détermination par chromatographie en phase gazeuse

des solvants présents dans les solutions de liant, les émulsions, les dispersions, ainsi que les peintures

et vernis diluables à l’eau.

Avec la fidélité indiquée à l’Article 13, il est possible de déterminer de manière quantitative les

constituants d’une concentration supérieure à 0,02 % (en fraction massique).

La méthode définie dans le présent document ne s’applique pas à la mesure de la teneur en composés

organiques volatils (COV) et en composés organiques semi-volatils (COSV).
[2]
NOTE Pour la quantification des COV et des COSV, voir l’ISO 11890-2 .
2 Références normatives

Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur

contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique.

Pour les références non datées, la dernière édition du document de référence s’applique (y compris les

éventuels amendements).
ISO 4618, Peintures et vernis — Termes et définitions

ISO 15528, Peintures, vernis et matières premières pour peintures et vernis — Échantillonnage

3 Termes et définitions

Pour les besoins du présent document, les termes et définitions donnés dans l’ISO 4618 s’appliquent.

L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en

normalisation, consultables aux adresses suivantes :

— ISO Online browsing platform: disponible à l’adresse https:// www .iso .org/ obp

— IEC Electropedia: disponible à l’adresse http:// www .electropedia .org/
4 Unités

Les résultats analytiques sont exprimés sous forme de fraction massique, en pourcentage.

5 Principe

Une fois l’échantillon préparé, les constituants de l’échantillon d’essai sont séparés par chromatographie

en phase gazeuse. Il est possible d’utiliser un système d’injection à chaud ou à froid, en fonction du type

de produit. Une fois les constituants identifiés, ils sont quantifiés à partir des aires des pics selon la

méthode de l’étalon interne.
© ISO 2019 – Tous droits réservés 1
---------------------- Page: 5 ----------------------
ISO 22518:2019(F)
6 Appareillage
6.1 Chromatographe en phase gazeuse
6.1.1 Généralités

Le chromatographe en phase gazeuse doit pouvoir être utilisé avec des colonnes de séparation

capillaires et respecter les conditions énoncées en 6.1.2 à 6.1.4.

Toutes les pièces instrumentales entrant en contact avec l’échantillon d’essai doivent être constituées

d’un matériau, par exemple le verre, résistant à l’échantillon et ne modifiant pas chimiquement ce

dernier.
6.1.2 Système d’injection des échantillons
6.1.2.1 Système d’injection à chaud

L’instrument doit être équipé d’un bloc d’injection à température variable muni d’un diviseur

d’échantillon. La température d’injection doit pouvoir être réglée avec une exactitude de 1 K. Le rapport

de division doit être ajustable et doit pouvoir être suivi dans le temps. L’insert du diviseur d’échantillon

doit contenir de la laine de verre silanisée pour retenir les constituants non volatils. Il doit être nettoyé

et rempli avec de la laine de verre neuve, ou bien remplacé, au besoin, pour éviter toute erreur liée

à la présence de résidus de liant ou de pigment (adsorption de solvants par exemple). La survenue

d’une adsorption est révélée par l’apparition de traînées de pics, en particulier avec les constituants

faiblement volatils.
6.1.2.2 Système d’injection à froid

Le système d’injection à froid doit être équipé d’une programmation en température assurant un

chauffage de la température ambiante à 300 °C, et l’injecteur du diviseur d’échantillon doit être constitué

d’un matériau tel que le verre. Il doit comporter un remplissage en laine de verre silanisée et doit être

traité comme indiqué en 6.1.2.1. Dans ce cas également le rapport de division doit être ajustable et doit

pouvoir être suivi.
6.1.2.3 Système d’injection automatique des échantillons

La fidélité de la méthode augmente si les systèmes d’injection, notamment le système d’injection à

chaud, sont couplés à un injecteur automatique. En cas d’utilisation d’un injecteur automatique, suivre

les instructions du fabricant.
6.1.3 Four

Le four doit pouvoir être chauffé entre 40 °C et 300 °C de manière isotherme et avec une régulation de

température programmée. La température du four doit p
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.