ISO 19499:2007

Mechanical vibration — Balancing — Guidance on the use and application of balancing standards

ISO 19499:2007 provides an introduction to balancing and directs the user through the available International Standards associated with rotor balancing. It gives guidance on which of these standards should be used. Individual procedures are not included as these will be found in the appropriate International Standards.

Vibrations mécaniques — Équilibrage — Lignes directrices pour l'utilisation et l'application de normes d'équilibrage

General Information

• Status: Withdrawn
• Publication Date: 08-Jul-2007
• Withdrawal Date: 08-Jul-2007
• ICS: 21.120.40 - Balancing and balancing machines
• Technical Committee: ISO/TC 108/SC 2 - Measurement and evaluation of mechanical vibration and shock as applied to machines, vehicles and structures
• Drafting Committee: ISO/TC 108/SC 2/WG 31 - Balancing
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 19-Feb-2019

Relations

• Revised: ISO 21940-1:2019 - Mechanical vibration — Rotor balancing — Part 1: Introduction
• Effective Date: 06-May-2017

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 19499
First edition
2007-07-15

Mechanical vibration — Balancing —
Guidance on the use and application of
balancing standards
Vibrations mécaniques — Équilibrage — Lignes directrices pour
l'utilisation et l'application de normes d'équilibrage




Reference number
ISO 19499:2007(E)
©
ISO 2007

---------------------- Page: 1 ----------------------
ISO 19499:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 19499:2007(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Fundamentals of balancing . 1
4.1 General. 1
4.2 Unbalance distribution. 2
4.3 Unbalance representation. 2
5 Balancing considerations . 3
5.1 General. 3
5.2 Rotors with rigid behaviour . 3
5.3 Rotors with flexible behaviour . 4
5.4 Rotors with special behaviour. 5
5.5 Examples of rotor behaviours . 5
5.6 Influencing factors. 6
6 Balance tolerances . 7
6.1 General. 7
6.2 Permissible residual unbalances. 7
6.3 Vibration limits . 7
7 Selection of a balancing procedure. 7
7.1 General. 7
7.2 Selection of a balancing procedure when none is specified . 8
8 International Standards on balancing . 13
8.1 General. 13
8.2 Vocabulary. 13
8.3 Balancing procedures and tolerances. 14
8.4 Balancing machines . 15
8.5 Machine design for balancing . 15
8.6 Machine vibration . 16
Annex A (informative) Mathematical and graphical representation of unbalance . 17
Annex B (informative) Examples of different rotor behaviours. 27
Annex C (informative) How to determine rotor flexibility based on an estimation from its
geometric design . 32
Bibliography . 35

© ISO 2007 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 19499:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 19499 was prepared by Technical Committee ISO/TC 108, Mechanical vibration, shock and condition
monitoring.
iv © ISO 2007 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 19499:2007(E)
Introduction
Vibration caused by rotor unbalance is one of the most critical issues in the design and maintenance of
machines. It gives rise to dynamic forces which adversely impact both machine and human health and well-
being. The purpose of this International Standard is to provide a common framework for balancing rotors so
that appropriate methods will be used. This standard serves essentially as guidance on the usage of other
International Standards on balancing in that it categorizes types of machine unbalance. As such, it can be
viewed as an introductory standard to the series of International Standards on balancing developed by
ISO/TC 108.
Balancing is explained in a general manner, as well as the unbalance of a rotor. A certain representation of
the unbalance is recommended for an easier understanding of the necessary unbalance corrections.

© ISO 2007 – All rights reserved v

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 19499:2007(E)

Mechanical vibration — Balancing — Guidance on the use and
application of balancing standards
1 Scope
This International Standard provides an introduction to balancing and directs the user through the available
International Standards associated with rotor balancing. It gives guidance on which of these standards should
be used. Individual procedures are not included here as these will be found in the appropriate International
Standards.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1925:2001, Mechanical vibration — Balancing — Vocabulary
ISO 2041, Vibration and shock — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 1925 and ISO 2041 apply.
4 Fundamentals of balancing
4.1 General
Balancing is a procedure by which the mass distribution of a rotor (or part or module) is checked and, if
necessary, adjusted to ensure that balance tolerances are met.
Rotor unbalance may be caused by many factors, including material, manufacture and assembly, wear during
operation, debris or an operational event. It is important to understand that every rotor, even in series
production, has an individual unbalance distribution.
New rotors are commonly balanced by the manufacturer in specially designed balancing machines before
installation into their operational environment. Following rework or repair, rotors may be rebalanced in a
balancing machine or, if appropriate facilities are not available, the rotor may be balanced in situ (see
ISO 20806 for details). In the latter case, the rotor is held in its normal service bearings and support structure
and installed within its operational drive train.
The unbalance on the rotor generates centrifugal forces when it is rotated in a balancing machine or in situ.
These forces may be directly measured by force gauges mounted on the structures supporting the bearings or
indirectly by measuring either the motion of the pedestal or the shaft. From these measurements, the
unbalance can be calculated and balancing achieved by adding, removing or shifting of correction masses on
the rotor. Depending on the particular balancing task, the corrections are performed in one, two or more
correction planes.
© ISO 2007 – All rights reserved 1

---------------------- Page: 6 ----------------------
ISO 19499:2007(E)
4.2 Unbalance distribution
In reality, unbalance is made up of an infinite number of unbalance vectors, distributed along the shaft axis of
the rotor. If a lumped-mass model is used to represent the rotor, unbalance may be represented by a finite
number of unbalance vectors of different magnitude and angular direction as illustrated in Figure 1.

Figure 1 — Unbalance distribution in a rotor modelled as 10 elements perpendicular to the z-axis

If all unbalance vectors were corrected in their respective planes, then the rotor would be perfectly balanced.
In practice, it is not possible to measure these individual unbalances and it is not necessary. A more
condensed description is needed, leading to practical balancing procedures.
4.3 Unbalance representation
Rotor unbalance can be expressed by a combination of the following three kinds of unbalance
representations:
G
a) resultant unbalance, U , the vector sum of all unbalance vectors distributed along the rotor;
r
G
b) resultant moment unbalance, P , the vector sum of the moments of all the unbalance vectors distributed
r
along the rotor about the arbitrarily selected plane of the resultant unbalance;
G
c) modal unbalance, U , that unbalance distribution which affects only the nth natural mode of a
n
rotor/bearing system.
Mathematical and graphical representations of unbalances are shown in Annex A.
NOTE Resultant unbalance [see 4.3 a)] and resultant moment unbalance [see 4.3 b)] can be combined. The
combination is called “dynamic unbalance” and is represented by two unbalances in two arbitrarily chosen planes
perpendicular to the shaft axis.
2 © ISO 2007 – All rights reserved

---------------------- Page: 7 ----------------------
ISO 19499:2007(E)
5 Balancing considerations
5.1 General
In the past, International Standards classified all rotors to be either rigid or flexible, and balancing procedures
for these two main classes of rotors are given in ISO 1940-1 and ISO 11342, respectively (see Table 1).
However, the simple rigid/flexible classification is a gross simplification, which can lead to a misinterpretation
and suggests that the balance classification of the rotor is only dependent on its physical construction.
Unbalance is an intrinsic property of the rotor, but the behaviour of the rotor and its response to unbalance in
its normal operating environment are affected by the dynamics of the bearings and support structure, and by
its operating speed. Furthermore, the balance quality to which the rotor is expected to run and the magnitude
and distribution of the initial unbalance along the rotor will dictate which balancing procedure is necessary;
see Table 1.
Table 1 — Overview of rotor behaviour, related International Standards and balancing procedures
Rotor behaviour Example Related Balancing task or procedure
International
(Numbers refer to (Letters as used in ISO 11342:1998)
Standard
subclauses in this
International Standard)
a
Rigid behaviour (5.2) Figure 4 a) ISO 1940-1
One- and two-plane balancing
Six low-speed balancing procedures (A to F)
Balancing procedure at multiple speeds (G)
Flexible behaviour (5.3) Figure 4 b)
Balancing procedure for one speed only (usually
service speed) (H)
b
ISO 11342
Component elastic
Figure 4 c) Fixed-speed balancing procedure (I)
behaviour (5.4.2)
Component seating
c
Figure 4 d)
Settling of components at high speed
behaviour (5.4.3)
a
One- and two-plane balancing includes balancing the resultant unbalance and the resultant moment unbalance.
b
ISO 11342:1998 uses “flexible” as a generic term that includes flexible, component elastic and component seating behaviours.
c
This procedure is mentioned in Clause 7 of ISO 11342:1998, but no designated letter is given.

5.2 Rotors with rigid behaviour
An ideal rotor when rotating, with rigid behaviour on elastic supports, will undergo displacements that are
combinations of the two dynamic rigid-body modes, as seen in Figure 2 for a simple symmetric rotor with
unbalance. There is no flexure of the rotor and all displacements of the rotor arise from movements of the
bearings and their support structure.

Figure 2 — Rigid-body modes of a symmetric rotor on a symmetric elastic support structure

© ISO 2007 – All rights reserved 3

---------------------- Page: 8 ----------------------
ISO 19499:2007(E)
In reality, no rotor will be totally rigid and will have small flexural deflections in relation to the gross rigid-body
motion of the rotor. However, the rotor may be regarded as rigid provided these deflections caused by a given
unbalance distribution are below the required tolerances at any speed up to the maximum service speed. The
majority of such rotors, and indeed many manufactured rotors, can be balanced as rigid rotors, in accordance
with the requirements of ISO 1940-1. This aims at balancing the resultant unbalance with at least a single-
plane balance correction, or the dynamic unbalance with a two-plane balance correction.
NOTE Rotors designated to have rigid behaviour in the operating environment can be balanced at any speed on the
balancing machine provided the speed is sufficiently low to ensure the rotor still operates with a rigid behaviour.
5.3 Rotors with flexible behaviour
5.3.1 General
If the speed is increased or the tolerance reduced for the same rotor described in 5.2, it may become
necessary to take flexible behaviour into account. Here the deflection of the rotor is significant, and rigid-body
balancing procedures are not sufficient to achieve a desired balance condition. Figure 3 shows typical flexural
mode shapes for a symmetric rotor. For these rotors that exhibit flexural behaviour, the balancing procedures
in ISO 11342 should be adopted.
5.3.2 Low-speed balancing
In special circumstances, even rotors with flexible behaviour may be balanced satisfactorily at low speed.
ISO 11342:1998 describes procedures A to F, which, as far as possible, all aim to correct the unbalance in
their planes of origin.
5.3.3 Multiple-speed balancing
This procedure should be used to balance the resultant unbalance, the resultant moment unbalance and the
relevant modal unbalances, according to ISO 11342:1998, procedure G.

a)  First mode

b)  Second mode

c)  Third mode
Figure 3 — Schematic representation of the first three flexural modes of a rotor with flexible behaviour
on an elastic support structure
4 © ISO 2007 – All rights reserved

---------------------- Page: 9 ----------------------
ISO 19499:2007(E)
5.3.4 Service speed balancing
These rotors are flexible and pass through one or more critical speeds on their way up to service speed.
However, due to operating conditions or machine construction, high levels of vibration can be tolerated at the
critical speeds and the rotor is only balanced at the service speed according to ISO 11342:1998, procedure H.
5.4 Rotors with special behaviour
5.4.1 General
The majority of rotors will exhibit either rigid or flexible behaviours, but the following special behaviours can
exist and must be considered to achieve a successful balancing of the rotor.
5.4.2 Elastic behaviour of components
These rotors can have a shaft and body construction that either requires low-speed or high-speed balancing
procedures. However, in addition, they have one or more components that themselves are either flexible or
are flexibly mounted so that the unbalance of the whole system might consistently change with speed.
Examples of such rotors are a rotor with tie bars that deflect at high speed, rubber-bladed fans and single-
phase induction motors with a centrifugal switch. These should be balanced in accordance with
ISO 11342:1998, procedure I.
5.4.3 Seating behaviour of components
These rotors can have a construction where components settle after reaching a certain speed or other
condition. This movement will then become stable after one or just a few events. The components will reach a
final position and become re-seated, after which the rotor may require further balancing. Examples are
shrunk-on turbine discs, built-up rotors, copper winding in generators and generator retaining rings.
Subsequent behaviour of the rotor will then dictate the balancing procedure required. This rotor behaviour is
mentioned in Clause 7 of ISO 11342:1998, but no procedure is specified.
5.5 Examples of rotor behaviours
The different behaviours may be represented by the following rotors (see Figure 4):

a)  Rigid behaviour (a solid gear wheel) b)  Flexible behaviour (a disc on an elastic shaft,
for example a Laval rotor)

c)  Component elastic behaviour (a drum with tie bars, d)  Seating behaviour (a generator rotor with windings,
elastically deflecting under the centrifugal load) once for all seating under a certain centrifugal load)
Figure 4 — Examples of rotor types that demonstrate particular rotor behaviours
© ISO 2007 – All rights reserved 5

---------------------- Page: 10 ----------------------
ISO 19499:2007(E)
Such illustrations are not sufficient for a full description: obviously, rotors such as those shown in Figures 4 c)
and 4 d) may also show flexible behaviour; on the contrary, a rotor such as Figure 4 b) could be a low-speed
fan without considerable flexible behaviour, i.e. a rotor with a rigid behaviour. Details of these types of
behaviour are further explained in Annex B.
5.6 Influencing factors
5.6.1 General
A rotor’s response characteristic is defined by its physical properties and those of its supporting structure. The
vibration response measured at the supporting structure or on the rotor will depend on these physical
properties plus the magnitude of unbalance and its distribution along the rotor, as well as the speed of rotation.
Balancing to a required tolerance will therefore depend on all these parameters, and changing these or the
tolerance specified may change the procedure needed to meet that tolerance.
5.6.2 Tolerances
By simply reducing the balance tolerance, it may be necessary to reconsider the behaviour of the rotor and
adopt a different procedure to bring the rotor within tolerance, as given in the following examples.
a) A rotor with rigid behaviour, balanced using a single-plane procedure to reduce resultant unbalance, may
simply require additional more accurate single-plane balancing.
b) A rotor with rigid behaviour, balanced using a single-plane procedure to reduce resultant unbalance, may
also require a two-plane procedure to take into account the moment unbalance (or both resultant and
moment unbalance together as a dynamic unbalance).
c) A rotor with rigid behaviour, balanced in two planes to reduce both resultant and moment unbalance (or
both resultant and moment unbalance together as a dynamic unbalance), may additionally require flexible
behaviour procedures to reduce contributions from the modal unbalances, even though the rotor is
running below its first flexural critical speed.
d) A rotor with flexible behaviour, for which a flexible rotor behaviour procedure has been carried out to
reduce the dynamic unbalance and a number of modal unbalances, may require additional flexible rotor
behaviour procedures to reduce modal unbalances of even more (higher) flexural modes of the rotor,
even though the rotor is running below the flexural critical speeds of the higher modes.
e) A rotor with either rigid or flexible behaviour, successfully balanced using the appropriate procedure, may
need to consider special procedures to take into account component elastic or component seating
behaviours.
f) Where a tighter tolerance can only be achieved at a single speed, the service speed balancing procedure
may need to be considered.
5.6.3 Speed and support conditions
Other changes of rotor behaviour may occur if operational conditions are changed (e.g. by changing speed or
support conditions).
5.6.4 Initial unbalance
The initial unbalance distribution has an influence on the response of the rotor system. It determines which
unbalance (see Clause 4) is out of tolerance and therefore needs treatment. Different manufacturing and
assembling procedures can lead to different levels of initial unbalance.
6 © ISO 2007 – All rights reserved

---------------------- Page: 11 ----------------------
ISO 19499:2007(E)
6 Balance tolerances
6.1 General
The balancing equipment and techniques available enable unbalances to be reduced to low limits. However, it
would be uneconomic to over-specify the quality requirements. It is therefore necessary to define the optimum
balance quality for the rotor to operate with acceptable vibration and dynamic forces in its normal service
environment.
6.2 Permissible residual unbalances
There is a direct relation between rotor unbalance and the once-per-revolution vibration under service
conditions. The relationship depends on the machine’s dynamic characteristics (i.e. rotor, structure and
bearing dynamic properties). However, the overall machine vibration may be due only in part to the presence
of rotor unbalance. Other sources of vibration could be magnetic or fluid forces.
Guidance on the derivation of permissible residual unbalance tolerances is given in
⎯ ISO 1940-1 for a rigid rotor behaviour, and
⎯ ISO 11342, using tolerance data from ISO 1940-1, for other rotor behaviours.
6.3 Vibration limits
There is no easily recognizable relationship between the machine vibration under service conditions and
vibration in the balancing machine. The relation depends on the differences between the bearings and the
support structure used in the balancing machine and installed condition. Further, the rotor in the balancing
machine is tested in isolation and does not include effects from other rotors in the shaft line, as experienced
when installed in its operational environment. It should be noted that different balancing machines may have
different pedestal stiffness and therefore vibration limits have to be set individually for each balancing machine.
Where detailed information is available concerning these parameters, a method to estimate these limits is
presented in ISO 11342. In-situ vibration limits are presented in the appropriate parts of ISO 7919 for rotating
shafts and ISO 10816 for non-rotating parts.
Where insufficient detail is available to obtain these parameters, guidance should be taken from the balancing
machine facility from which rotors have operated satisfactorily in situ.
7 Selection of a balancing procedure
7.1 General
Since different balancing procedures require different types of balancing machines and resource input, it is
important to select an appropriate procedure (see Table 1) to optimize the balancing process to meet the
required balance tolerances.
Rotors with a rigid behaviour (see 5.2) can be balanced using the single- and two-plane balancing guidelines
provided in ISO 1940-1.
In general, rotors with a flexible behaviour (see 5.3) should be dealt with in accordance with the guidelines
given in ISO 11342, where a number of procedures are defined for different rotor configurations:
⎯ the general procedure is that for multiple-speed balancing, see 5.3.3 (procedure G of ISO 11342:1998);
⎯ rotors that spend most of their time at a single speed can use service speed balancing (see 5.3.4;
(procedure H of ISO 11342:1998);
© ISO 2007 – All rights reserved 7

---------------------- Page: 12 ----------------------
ISO 19499:2007(E)
⎯ rotors that have flexible behaviour that can be adequately balanced at low speed (see 5.3.2; procedures
A to F of ISO 11342:1998).
The procedure for rotors with component elastic behaviour, see 5.4.2, is given in ISO 11342:1998
(procedure I).
For rotors with component seating behaviour (see 5.4.3), it is first necessary for the rotor to be taken to the
speed (or condition) at which the unbalance is stabilized and then balanced using the appropriate procedure
for the rigid rotor behaviour (see ISO 1940-1) or flexible rotor behaviour (see ISO 11342).
Where possible, consult the rotor manufacturer or the user for a recommended balancing procedure. In the
case of the rotor with flexible behaviour, a definition of the rotor configuration, as defined by ISO 11342, would
suffice.
7.2 Selection of a balancing procedure when none is specified
7.2.1 Identify the rotor behaviour
Clause 5 introduces the major types of rotor behaviour and Table 2 gives guidance on selection of the
balancing procedure together with the expected balancing machine to be used. A consideration of the balance
tolerances must be taken into account when identifying the rotor behaviour, as discussed in 7.2.2.
WARNING — Guidance given in Table 2 should be used with care as the ratio of rotor speed to first
flexural resonance in situ is only a typical value. This will be highly dependent on the dynamic
characteristics of the bearings and their supports, initial unbalance, the balance quality required, and
the detailed design of the rotor.
Although the behaviour of many rotors can be easily identified from the simple guidance given in both
Clause 5 and Table 2, others will require a full analysis, particularly when making the distinction between rigid
and flexible behaviours. Table 2 requires knowledge of the critical speeds, which are often unknown. Annex C
presents an analytical method to obtain estimates of rotor flexibility in the operating environment.

8 © ISO 2007 – All rights reserved

----------------------
...