ISO 16564:2004/Amd 1:2006

Rubber, raw natural — Determination of average molecular mass and molecular-mass distribution by size exclusion chromatography (SEC) — Amendment 1

Caoutchouc naturel brut — Détermination de la masse moléculaire moyenne et de la répartition des masses moléculaires par chromatographie d'exclusion stérique (SEC) — Amendement 1

General Information

• Status: Published
• Publication Date: 14-May-2006
• ICS: 83.040.10 - Latex and raw rubber
• Technical Committee: ISO/TC 45/SC 3 - Raw materials (including latex) for use in the rubber industry
• Drafting Committee: ISO/TC 45/SC 3/WG 5 - Synthetic and reclaimed rubber
• Current Stage: 6060 - International Standard published
• Start Date: 30-Jan-2006
• Due Date: 22-Nov-2007
• Completion Date: 15-May-2006

Relations

• Amends: ISO 16564:2004 - Rubber, raw natural — Determination of average molecular mass and molecular-mass distribution by size exclusion chromatography (SEC)
• Effective Date: 06-Jun-2022
• Child: ISO 16564:2004 - Rubber, raw natural — Determination of average molecular mass and molecular-mass distribution by size exclusion chromatography (SEC)
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 16564
First edition
2004-10-01
AMENDMENT 1
2006-05-15
Rubber, raw natural — Determination of
average molecular mass and molecular-
mass distribution by size exclusion
chromatography (SEC)
AMENDMENT 1
Caoutchouc naturel brut — Détermination de la masse moléculaire
moyenne et de la répartition des masses moléculaires par
chromatographie d'exclusion stérique (SEC)
AMENDEMENT 1




Reference number
ISO 16564:2004/Amd.1:2006(E)
©
ISO 2006

---------------------- Page: 1 ----------------------
ISO 16564:2004/Amd.1:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2006 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 16564:2004/Amd.1:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 16564:2004 was prepared by Technical Committee ISO/TC 45, Rubber and rubber
products, Subcommittee SC 2, Testing and analysis.

© ISO 2006 – All
...