ISO/IEC 14443-2:2010/FDAmd 5
(Amendment)Identification cards — Contactless integrated circuit cards — Proximity cards — Part 2: Radio frequency power and signal interface — Amendment 5: Bit rates of 3fc/4, fc, 3fc/2 and 2fc from PCD to PICC
Identification cards — Contactless integrated circuit cards — Proximity cards — Part 2: Radio frequency power and signal interface — Amendment 5: Bit rates of 3fc/4, fc, 3fc/2 and 2fc from PCD to PICC
Cartes d'identification — Cartes à circuit(s) intégré(s) sans contact — Cartes de proximité — Partie 2: Interface radiofréquence et des signaux de communication — Amendement 5: Débits binaires de 3fc/4, fc, 3fc/2 et 2fc de PCD à PICC
General Information
Relations
Standards Content (Sample)
FINAL
ISO/IEC
AMENDMENT
DRAFT
14443-2:2010
FDAM 5
ISO/IEC JTC 1/SC 17
Identification cards — Contactless
Secretariat: BSI
integrated circuit cards — Proximity
Voting begins on:
2014-02-07 cards —
Voting terminates on:
Part 2:
2014-04-07
Radio frequency power and signal
interface
AMENDMENT 5: Bit rates of 3fc/4, fc,
3fc/2 and 2fc from PCD to PICC
Cartes d’identification — Cartes à circuit(s) intégré(s) sans contact —
Cartes de proximité —
Partie 2: Interface radiofréquence et des signaux de communication
AMENDEMENT 5: Débits binaires de 3fc/4, fc, 3fc/2 et 2fc de PCD à
PICC
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/IEC 14443-2:2010/FDAM 5:2014(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO/IEC 2014
---------------------- Page: 1 ----------------------
ISO/IEC 14443-2:2010/FDAM 5:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO/IEC 2014 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC 14443-2:2010/FDAM 5:2014(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are
members of ISO or IEC participate in the development of International Standards through technical
committees established by the respective organization to deal with particular fields of technical
activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international
organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the
work. In the field of information technology, ISO and IEC have established a joint technical committee,
ISO/IEC JTC 1.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for
the different types of document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject
of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
Details of any patent rights identified during the development of the document will be in the Introduction
and/or on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/IEC JTC 1, Information technology, SC 17, Card and
personal identification.
© ISO/IEC 2014 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/IEC 14443-2:2010/FDAM 5:2014(E)
Identification cards — Contactless integrated circuit cards
— Proximity cards —
Part 2:
Radio frequency power and signal interface
AMENDMENT 5: Bit rates of 3fc/4, fc, 3fc/2 and 2fc from PCD to
PICC
Page 2, Clause 4
Add the following new symbols to the list in alphabetical order:
AP actual phase value
ACP actual constellation point
EPI elementary phase interval
etu elementary time unit
ISI inter symbol interference
ISI inter symbol interference angle
d
ISI inter symbol interference magnitude
m
NP nominal phase value
P complex constellation point of the maximum NP
H
P complex constellation point of the minimum NP
L
PNP previous nominal phase
PR phase range
PSK phase shift keying
# number
Page 6, 8.1.1
Replace the subclause with the following:
“The bit rate for the transmission during initialization and anticollision shall b
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.