ISO 15967:2000
(Main)Direct reduced iron — Determination of tumble strength of hot briquetted iron (HBI)
Direct reduced iron — Determination of tumble strength of hot briquetted iron (HBI)
Minerais de fer préréduits — Essai au tambour du fer briqueté à chaud
Neposredno reducirano železo - Ugotavljanje porušitvene trdnosti vroče briketiranega železa
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 15967
First edition
2000-08-15
Direct reduced iron — Determination of
tumble strength of hot briquetted iron (HBI)
Minerais de fer préréduits — Essai au tambour du fer briqueté à chaud
Reference number
ISO 15967:2000(E)
©
ISO 2000
---------------------- Page: 1 ----------------------
ISO 15967:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 15967:2000(E)
Contents Page
Foreword.iv
Introduction.v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Sampling and sample preparation.2
5 Test method.2
5.1 Principle.2
5.2 Apparatus .2
5.3 Preparation of test portions.3
5.4 Procedure .3
5.5 Expression of results .4
5.6 Number of tests and permissible tolerances.5
5.7 Test report .5
6 Verification .5
Annex A (normative) Operating procedure steps for the determination of tumble strength of HBI .6
Annex B (normative) Flowsheet for the procedure for the acceptance of test results.7
© ISO 2000 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 15967:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 15967 was prepared by Technical Committee ISO/TC 102, Iron ore and direct reduced
iron, Subcommittee SC 5, Physical testing of direct reduction feedstock and DRI.
Annexes A and B form a normative part of this International Standard,
iv © ISO 2000 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 15967:2000(E)
Introduction
The international trade of hot briquetted iron (HBI) as a merchant commodity is increasing rapidly and is expected
to grow beyond 10 million tonnes per annum in the twenty-first century. This has led to the need for the
development of test method standards for HBI.
This International Standard specifies a method for the determination of the tumble strength of HBI. The test gives a
relative measure of the resistance of HBI to size degradation by impact and abrasion, following the same principle
as the tumble test for iron ores (see ISO 3271). The level of degradation measured in the test has been found to be
similar to that experienced by HBI during ship loading, transport and bulk materials handling operations.
© ISO 2000 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 15967:2000(E)
Direct reduced iron — Determination of tumble strength of hot
briquetted iron (HBI)
WARNING — This International Standard may involve hazardous materials, operations and equipment. This
International Standard does not purport to address all of the safety problems associated with its use. It is
the responsibility of the user of this International Standard to establish appropriate safety and health
practices and to determine the applicability of regulatory limitations prior to use.
1 Scope
This International Standard specifies a method for the determination of the tumble strength of hot briquetted iron
(HBI).
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 3310-1:2000, Test sieves — Technical requirements and testing — Part 1: Test sieves of metal wire cloth.
ISO 3310-2:1999, Test sieves — Technical requirements and testing — Part 2: Test sieves of perforated metal
plate.
ISO 10835:1995, Direct reduced iron — Sampling and sample preparation — Manual methods for reduced pellets
and lump ores.
ISO 11323:1996, Iron ores — Vocabulary.
3 Terms and definitions
For the purposes of this International Standard, the terms and definitions given in ISO 11323 and the following
apply.
3.1
tumble index of HBI
relative measure of the tumble strength of the HBI expressed as the mass percentage of the � 6,3mm sizefraction
following a tumble test
3.2
abrasion index of HBI
relative measure of the size degradation of the HBI by abrasion expressed as the mass percentage of the
� 500µm size fraction following a tumble test
© ISO 2000 – All rights reserved 1
---------------------- Page: 6
...
SLOVENSKI STANDARD
SIST ISO 15967:2002
01-januar-2002
1HSRVUHGQRUHGXFLUDQRåHOH]R8JRWDYOMDQMHSRUXãLWYHQHWUGQRVWLYURþH
EULNHWLUDQHJDåHOH]D
Direct reduced iron -- Determination of tumble strength of hot briquetted iron (HBI)
Minerais de fer préréduits -- Essai au tambour du fer briqueté à chaud
Ta slovenski standard je istoveten z: ISO 15967:2000
ICS:
73.060.10 Železove rude Iron ores
SIST ISO 15967:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 15967:2002
---------------------- Page: 2 ----------------------
SIST ISO 15967:2002
INTERNATIONAL ISO
STANDARD 15967
First edition
2000-08-15
Direct reduced iron — Determination of
tumble strength of hot briquetted iron (HBI)
Minerais de fer préréduits — Essai au tambour du fer briqueté à chaud
Reference number
ISO 15967:2000(E)
©
ISO 2000
---------------------- Page: 3 ----------------------
SIST ISO 15967:2002
ISO 15967:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 15967:2002
ISO 15967:2000(E)
Contents Page
Foreword.iv
Introduction.v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Sampling and sample preparation.2
5 Test method.2
5.1 Principle.2
5.2 Apparatus .2
5.3 Preparation of test portions.3
5.4 Procedure .3
5.5 Expression of results .4
5.6 Number of tests and permissible tolerances.5
5.7 Test report .5
6 Verification .5
Annex A (normative) Operating procedure steps for the determination of tumble strength of HBI .6
Annex B (normative) Flowsheet for the procedure for the acceptance of test results.7
© ISO 2000 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 15967:2002
ISO 15967:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 15967 was prepared by Technical Committee ISO/TC 102, Iron ore and direct reduced
iron, Subcommittee SC 5, Physical testing of direct reduction feedstock and DRI.
Annexes A and B form a normative part of this International Standard,
iv © ISO 2000 – All rights reserved
---------------------- Page: 6 ----------------------
SIST ISO 15967:2002
ISO 15967:2000(E)
Introduction
The international trade of hot briquetted iron (HBI) as a merchant commodity is increasing rapidly and is expected
to grow beyond 10 million tonnes per annum in the twenty-first century. This has led to the need for the
development of test method standards for HBI.
This International Standard specifies a method for the determination of the tumble strength of HBI. The test gives a
relative measure of the resistance of HBI to size degradation by impact and abrasion, following the same principle
as the tumble test for iron ores (see ISO 3271). The level of degradation measured in the test has been found to be
similar to that experienced by HBI during ship loading, transport and bulk materials handling operations.
© ISO 2000 – All rights reserved v
---------------------- Page: 7 ----------------------
SIST ISO 15967:2002
---------------------- Page: 8 ----------------------
SIST ISO 15967:2002
INTERNATIONAL STANDARD ISO 15967:2000(E)
Direct reduced iron — Determination of tumble strength of hot
briquetted iron (HBI)
WARNING — This International Standard may involve hazardous materials, operations and equipment. This
International Standard does not purport to address all of the safety problems associated with its use. It is
the responsibility of the user of this International Standard to establish appropriate safety and health
practices and to determine the applicability of regulatory limitations prior to use.
1 Scope
This International Standard specifies a method for the determination of the tumble strength of hot briquetted iron
(HBI).
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 3310-1:2000, Test sieves — Technical requirements and testing — Part 1: Test sieves of metal wire cloth.
ISO 3310-2:1999, Test sieves — Technical requirements and testing — Part 2: Test sieves of perforated metal
plate.
ISO 10835:1995, Direct reduced iron — Sampling and sample preparation — Manual methods for reduced pellets
and lump ores.
ISO 11323:1996, Iron ores — Vocabulary.
3 Terms and definitions
For the purposes of this International Standard, the terms and definitions given in ISO 11323 and the following
apply.
3.1
tumble index of HBI
relative measure of the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.