ISO 8124-1:2014/FDAmd 3

Safety of toys — Part 1: Safety aspects related to mechanical and physical properties — Amendment 3: Warnings and fibrous filling materials

Sécurité des jouets — Partie 1: Aspects de sécurité relatifs aux propriétés mécaniques et physiques — Amendement 3: .

General Information

• Status: Withdrawn
• ICS: 97.200.50 - Toys
• Technical Committee: ISO/TC 181 - Safety of toys
• Drafting Committee: ISO/TC 181/WG 1 - Mechanical and physical properties
• Current Stage: 5098 - Project deleted
• Completion Date: 09-Jun-2017

Relations

• Replaced By: ISO 8124-1:2018 - Safety of toys — Part 1: Safety aspects related to mechanical and physical properties
• Effective Date: 07-Oct-2017
• Amends: ISO 8124-1:2014 - Safety of toys — Part 1: Safety aspects related to mechanical and physical properties
• Effective Date: 27-Nov-2021

Standards Content (Sample)

FINAL
ISO
AMENDMENT
DRAFT
8124-1:2014
FDAM 3
ISO/TC 181
Safety of toys —
Secretariat: DS
Voting begins on:
Part 1:
2017-03-20
Safety aspects related to mechanical
Voting terminates on:
and physical properties
2017-05-15
AMENDMENT 3: Warnings and fibrous
filling materials
Sécurité des jouets —
Partie 1: Aspects de sécurité relatifs aux propriétés mécaniques et
physiques
AMENDEMENT 3: .
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO 8124-1:2014/FDAM 3:2017(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2017

---------------------- Page: 1 ----------------------
ISO 8124-1:2014/FDAM 3:2017(E)

COPYRIGHT PROTECTED DOCUMENT
©  ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 8124-1:2014/FDAM 3:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/ iso/ foreword .html
This document was prepared by Technical Committee ISO/TC 181, Safety of toys.
A list of all parts in the ISO 8124 series can be found on the ISO website.
© ISO 2017 – All rights reserved  iii

---------------------- Page: 3 ----------------------
ISO 8124-1:2014/FDAM 3:2017(E)
Safety of toys —
Part 1:
Safety aspects related to mechanical and physical
properties
AMENDMENT 3: Warnings and fibrous filling materials
3 Terms and definitions
Replace the existing terminological entry with the following:
3.11
cord
narrow piece of flexible textile or non-textile material, the length of which is significantly greater than
the thickness and width
EXAMPLE  Cord includes elastic material, monofilament polymeric material, tape, ribbon, rope, strap, chain,
woven and twisted material and string, as well as certain weak and long springs.
Note 1 to entry Electrical cables (see 3.X.9) are not considered to be cords. Accessible electrical wires (for
example between a battery box and a sound source in a soft filled toy) which are not electrical cables are,
however, considered to be cords.
Add the following new terminological entry:
3.XX
elastic
material or item that is stretchable when subjected to an external force and which is able to recover or
nearly recover its original length or shape when the force is removed
Rep
...