Hexalobular socket head cap screws

ISO 14579:2011 specifies the characteristics of hexalobular socket head cap screws, with thread sizes from M2 up to and including M20, of product grade A.

Vis à métaux à tête cylindrique à six lobes internes

L'ISO 14579:2010 spécifie les caractéristiques des vis à métaux à tête cylindrique à six lobes internes, de filetage M2 à M20 inclus et de grade A.

General Information

Status
Published
Publication Date
15-Mar-2011
Current Stage
9093 - International Standard confirmed
Completion Date
29-Jun-2021
Ref Project

Relations

Buy Standard

Standard
ISO 14579:2011 - Hexalobular socket head cap screws
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 14579:2011 - Vis a métaux a tete cylindrique a six lobes internes
French language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 14579
Second edition
2011-03-15
Hexalobular socket head cap screws
Vis à métaux à tête cylindrique à six lobes internes
Reference number
ISO 14579:2011(E)
ISO 2011
---------------------- Page: 1 ----------------------
ISO 14579:2011(E)
PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but

shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In

the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

COPYRIGHT PROTECTED DOCUMENT
© ISO 2011

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 14579:2011(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through ISO

technical committees. Each member body interested in a subject for which a technical committee has been

established has the right to be represented on that committee. International organizations, governmental and

non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the

International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 14579 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 10, Product

standards for fasteners.

This second edition cancels and replaces the first edition (ISO 14579:2001), of which it constitutes a minor

revision.
© ISO 2011 – All rights reserved iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 14579:2011(E)
Hexalobular socket head cap screws
1 Scope

This International Standard specifies the characteristics of hexalobular socket head cap screws, with thread

sizes from M2 up to and including M20, of product grade A.

If, in special cases, specifications other than those listed in this International Standard are required, they can

be selected from existing International Standards, for example ISO 261, ISO 888, ISO 898-1, ISO 965-2,

ISO 965-3, ISO 3506-1 and ISO 4759-1.
2 Normative references

The following referenced documents are indispensable for the application of this document. For dated

references, only the edition cited applies. For undated references, the latest edition of the referenced

document (including any amendments) applies.

ISO 225, Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions

ISO 261, ISO general-purpose metric screw threads — General plan

ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws

and studs with specified property classes — Coarse thread and fine pitch thread

ISO 965-2, ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general

purpose external and internal screw threads — Medium quality

ISO 965-3, ISO general purpose metric screw threads — Tolerances — Part 3: Deviations for constructional

screw threads
ISO 3269, Fasteners — Acceptance inspection

ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1: Bolts, screws and

studs
ISO 4042, Fasteners — Electroplated coatings
ISO 4753, Fasteners — Ends of parts with external ISO metric thread

ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C

ISO 6157-1, Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements

ISO 6157-3, Fasteners — Surface discontinuities — Part 3: Bolts, screws and studs for special requirements

ISO 8839, Mechanical properties of fasteners — Bolts, screws, studs and nuts made of non-ferrous metals

ISO 8992, Fasteners — General requirements for bolts, screws, studs and nuts
ISO 10664, Hexalobular internal driving feature for bolts and screws
ISO 10683, Fasteners — Non-electrolytically applied zinc flake coatings
© ISO 2011 – All rights reserved 1
---------------------- Page: 4 ----------------------
ISO 14579:2011(E)
3 Dimensions

See Figure 1 and Table 1. Symbols and descriptions of dimensions are specified in ISO 225.

Dimensions in millimetres
Maximum underhead fillet, l = 1,7 r
f,max max
dd−
a,max s,max
r =
max
For r , see Table 1.
min
d applies if values of l are specified.
s s,min

The point shall be chamfered or, for threads u M4, may be as-rolled, in accordance with ISO 4753.

Incomplete thread u u 2P.

Top edge of head may be rounded or chamfered, as shown, at the discretion of the manufacturer.

Bottom edge of head may be rounded or chamfered to d but, in every case, shall be free of burrs.

Reference datum for d .
Figure 1
2 © ISO 2011 – All rights reserved
---------------------- Page: 5 ----------------------
ISO 14579:2011(E)
Table 1 — Dimensions
Dimensions in millimetres
M2 M2,5 M3 M4 M5 M6 M8
Thread, d
P 0,4 0,45 0,5 0,7 0,8 1 1,25
b ref. 16 17 18 20 22 24 28
max. 3,80 4,50 5,50 7,00 8,50 10,00 13,00
max. 3,98 4,68 5,68 7,22 8,72 10,22 13,27
min. 3,62 4,32 5,32 6,78 8,28 9,78 12,73
d max. 2,6 3,1 3,6 4,7 5,7 6,8 9,2
max. 2,00 2,50 3,00 4,00 5,00 6,00 8,00
min. 1,86 2,36 2,86 3,82 4,82 5,82 7,78
l max. 0,51 0,51 0,51 0,6 0,6 0,68 1,02
max. 2,00 2,50 3,00 4,00 5,00 6,0 8,00
min. 1,86 2,36 2,86 3,82 4,82 5,7 7,64
r min. 0,1 0,1 0,1 0,2 0,2 0,25 0,4
v max. 0,2 0,25 0,3 0,4 0,5 0,6 0,8
d min. 3,48 4,18 5,07 6,53 8,03 9,38 12,33
w min. 0,55 0,85 1,15 1,4 1,9 2,3 3,3
Socket no. 6 8 10 20 25 30 45
A ref. 1,75 2,4 2,8 3,95 4,5 5,6 7,95
Hexalobular
socket
max. 0,84 1,04 1,27 1,80 2,03 2,42 3,31
min. 0,71 0,91 1,01 1,42 1,65 2,02 2,92
...

NORME ISO
INTERNATIONALE 14579
Deuxième édition
2011-03-15
Vis à métaux à tête cylindrique à six
lobes internes
Hexalobular socket head cap screws
Numéro de référence
ISO 14579:2011(F)
ISO 2011
---------------------- Page: 1 ----------------------
ISO 14579:2011(F)
PDF – Exonération de responsabilité

Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier

peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence

autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées

acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute

responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.

Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info

du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir

l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,

veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2011

Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous

quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit

de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.

ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2011 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 14579:2011(F)
Avant-propos

L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de

normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée

aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du

comité technique créé à cet effet. Les organisations internationales, gouvernementales et non

gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec

la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.

Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,

Partie 2.

La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes

internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur

publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres

votants.

L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de

droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne

pas avoir identifié de tels droits de propriété et averti de leur existence.

L'ISO 14579 a été élaborée par le comité technique ISO/TC 2, Éléments de fixation, sous-comité SC 10,

Normes de produits pour éléments de fixation.

Cette deuxième édition annule et remplace la première édition (ISO 14579:2001), dont elle constitue une

révision mineure.
© ISO 2011 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
NORME INTERNATIONALE ISO 14579:2011(F)
Vis à métaux à tête cylindrique à six lobes internes
1 Domaine d'application

La présente Norme internationale spécifie les caractéristiques des vis à métaux à tête cylindrique à six lobes

internes, de diamètre de filetage M2 à M20 inclus et de grade A.

Si, dans des cas particuliers, des spécifications autres que celles figurant dans la présente Norme

internationale sont requises, elles peuvent être choisies dans les Normes internationales existantes, par

exemple l'ISO 261, l'ISO 888, l'ISO 898-1, l'ISO 965-2, l'ISO 3506-1 et l'ISO 4759-1.

2 Références normatives

Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les

références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du

document de référence s'applique (y compris les éventuels amendements).

ISO 225, Éléments de fixation — Vis, goujons et écrous — Symboles et description des dimensions

ISO 261, Filetages métriques ISO pour usages généraux — Vue d'ensemble

ISO 898-1, Caractéristiques mécaniques des éléments de fixation en acier au carbone et en acier allié —

Partie 1: Vis, goujons et tiges filetés de classes de qualités spécifiées — Filetage à pas gros et filetages à pas fin

ISO 965-2, Filetages métriques ISO pour usages généraux — Tolérances — Partie 2: Dimensions limites pour

filetages intérieurs et extérieurs d'usages généraux — Qualité moyenne

ISO 965-3 Filetages métriques ISO pour usages généraux — Tolérances — Partie 3: Écarts pour filetages de

construction
ISO 3269, Éléments de fixation — Contrôle de réception

ISO 3506-1, Caractéristiques mécaniques des éléments de fixation en acier inoxydable résistant à la

corrosion — Partie 1: Vis et goujons
ISO 4042, Éléments de fixation — Revêtements électrolytiques

ISO 4753, Éléments de fixation — Extrémités des éléments à filetage extérieur métrique ISO

ISO 4759-1, Tolérances des éléments de fixation — Partie 1: Vis, goujons et écrous — Grades A, B et C

ISO 6157-1, Éléments de fixation — Défauts de surface — Partie 1: Vis et goujons d'usage général

ISO 6157-3, Éléments de fixation — Défauts de surface — Partie 3: Vis et goujons pour applications

particulières

ISO 8839, Caractéristiques mécaniques des éléments de fixation — Vis, goujons et écrous en métaux non

ferreux
ISO 8992, Éléments de fixation — Exigences générales pour vis, goujons et écrous
ISO 10664, Empreintes à six lobes internes pour vis

ISO 10683, Éléments de fixation — Revêtements non électrolytiques de lamelles de zinc

© ISO 2011 – Tous droits réservés 1
---------------------- Page: 4 ----------------------
ISO 14579:2011(F)
3 Dimensions

Voir Figure 1 et Tableau 1. Les symboles et la description des dimensions sont spécifiés dans l'ISO 225.

Dimensions en millimètres
Raccordement sous tête maximal, l = 1,7 r
f,max max
dd−
a,max s,max
r =
max
Pour r , voir Tableau 1.
min
d s'applique si les valeurs de l sont spécifiées.
s s, min

Bout chanfreiné ou, pour les filetages inférieurs ou égaux à M4, «brut de roulage», conformément à l'ISO 4753.

Filetage incomplet u u 2P.

L'arête supérieure de la tête peut être arrondie ou chanfreinée comme indiqué, au choix du fabricant.

L'arête inférieure de la tête peut être arrondie ou chanfreinée jusqu'à d mais doit, dans tous les cas, être ébarbée.

Référence pour d .
Figure 1
2 © ISO 2011 – Tous droits réservés
---------------------- Page: 5 ----------------------
ISO 14579:2011(F)
Tableau 1 — Dimensions
Dimensions en millimètres
M2 M2,5 M3 M4 M5 M6 M8
Filetage, d
P 0,4 0,45 0,5 0,7 0,8 1 1,25
b réf. 16 17 18 20 22 24 28
max. 3,80 4,50 5,50 7,00 8,50 10,00 13,00
max. 3,98 4,68 5,68 7,22 8,72 10,22 13,27
min. 3,62 4,32 5,32 6,78 8,28 9,78 12,73
d max. 2,6 3,1 3,6 4,7 5,7 6,8 9,2
max. 2,00 2,50 3,00 4,00 5,00 6,00 8,00
min. 1,86 2,36 2,86 3,82 4,82 5,82 7,78
l max. 0,51 0,51 0,51 0,6 0,6 0,68 1,02
max. 2,00 2,50 3,00 4,00 5,00 6,0 8,00
min. 1,86 2,36 2,86 3,82 4,82 5,7 7,64
r min. 0,1 0,1 0,1 0,2 0,2 0,25 0,4
v max. 0,2 0,25 0,3 0,4 0,5 0,6 0,8
d min. 3,48 4,18 5,07 6,53 8,03 9,38 12,33
w min. 0,55 0,85 1,15 1,4 1,9 2,3 3,3
Empreinte n° 6 8 10 20 25 30 45
Empreinte
A réf. 1,75 2,4 2,8 3,95 4,5 5,6 7,95
à six
lobes
max. 0,84 1,04 1,27
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.