ISO 11119-2:2012/Amd 1:2014

Gas cylinders — Refillable composite gas cylinders and tubes — Design, construction and testing — Part 2: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 l with load-sharing metal liners — Amendment 1

Bouteilles à gaz — Bouteilles à gaz rechargeables en matériau composite et tubes — Conception, construction et essais — Partie 2: Bouteilles à gaz composites entièrement bobinées renforcées par des fibres et tubes d'une contenance allant jusqu'à 450 l avec liners métalliques transmettant la charge — Amendement 1

General Information

• Status: Withdrawn
• Publication Date: 10-Aug-2014
• Withdrawal Date: 10-Aug-2014
• ICS: 23.020.30 - Pressure vessels, gas cylinders
• ICS: 23.020.35 - Gas cylinders
• Technical Committee: ISO/TC 58/SC 3 - Cylinder design
• Drafting Committee: ISO/TC 58/SC 3/WG 27 - Composite cylinders
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 23-Nov-2020

Relations

• Revised: ISO 11119-2:2020 - Gas cylinders — Design, construction and testing of refillable composite gas cylinders and tubes — Part 2: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 l with load-sharing metal liners
• Effective Date: 12-May-2018
• Amends: ISO 11119-2:2012 - Gas cylinders — Refillable composite gas cylinders and tubes — Design, construction and testing — Part 2: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 l with load-sharing metal liners
• Effective Date: 04-Sep-2021

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11119-2
Second edition
2012-07-15
AMENDMENT 1
2014-08-15
Gas cylinders — Refillable composite
gas cylinders and tubes — Design,
construction and testing —
Part 2:
Fully wrapped fibre reinforced
composite gas cylinders and tubes up
to 450 l with load-sharing metal liners
AMENDMENT 1
Bouteilles à gaz — Bouteilles à gaz rechargeables en matériau
composite et tubes — Conception, construction et essais —
Partie 2: Bouteilles à gaz composites entièrement bobinées renforcées
par des fibres et tubes d’une contenance allant jusqu’à 450 l avec
liners métalliques transmettant la charge
AMENDEMENT 1
Reference number
ISO 11119-2:2012/Amd.1:2014(E)
©
ISO 2014

---------------------- Page: 1 ----------------------
ISO 11119-2:2012/Amd.1:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11119-2:2012/Amd.1:2014(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 58, Gas cylinders, Subcommittee SC 3, Cylinder
design.
© ISO 2014 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 11119-2:2012/Amd.1:2014(E)
Gas cylinders — Refillable composite gas cylinders and
tubes — Design, construc
...