Calculation of load capacity of bevel gears — Part 30: ISO rating system for bevel and hypoid gears — Sample calculations

ISO/TR 10300-30:2017 provides sample calculations for different bevel gear designs, how the load capacity is numerically determined according to the methods and formulae of the ISO 10300 series. The initial geometric gear data necessary for these calculations in accordance with ISO 23509. The term "bevel gear" is used to mean straight, helical (skew), spiral bevel, zerol and hypoid gear designs. Where this document pertains to one or more, but not all, the specific forms are identified. The manufacturing process of forming the desired tooth form is not intended to imply any specific process, but rather to be general in nature and applicable to all calculation methods of the ISO 10300 series. The fact that there are bevel gear designs with tapered teeth and others where the tooth depth remains constant along the face width (uniform depth) does not demand to apply Method B2 for the first and Method B1 for the second tooth configuration. The rating system of the ISO 10300 series is based on virtual cylindrical gears and restricted to bevel gears whose virtual cylindrical gears have transverse contact ratios of εvα

Calcul de la capacité de charge des engrenages coniques — Partie 30: Système d'évaluation ISO pour engrenages conique et hypoïde - Type de calculs

General Information

Status
Published
Publication Date
11-Dec-2017
Current Stage
9092 - International Standard to be revised
Completion Date
10-Nov-2021
Ref Project

Buy Standard

Technical report
ISO/TR 10300-30:2017 - Calculation of load capacity of bevel gears
English language
246 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

TECHNICAL ISO/TR
REPORT 10300-30
First edition
2017-12
Calculation of load capacity of bevel
gears —
Part 30:
ISO rating system for bevel and hypoid
gears — Sample calculations
Calcul de la capacité de charge des engrenages coniques —
Partie 30: Système d'évaluation ISO pour engrenages conique et
hypoïde - Type de calculs
Reference number
ISO/TR 10300-30:2017(E)
ISO 2017
---------------------- Page: 1 ----------------------
ISO/TR 10300-30:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/TR 10300-30:2017(E)
Contents Page
Foreword iv
Introduction v
1 Scope 1
2 Normative references 1
3 Terms and definitions 2
4 Symbols and abbreviated terms 2
5 Application 10
5.1 General 10
5.2 Structure of calculation methods 10

Annex A (informative) Sample 1: Rating of a spiral bevel gear pair without hypoid

offset according to Method B1 and Method B2 12

Annex B (informative) Sample 2: Rating of a hypoid gear set according to Method B1

and Method B2 65
Anne
x C (informative) Sample 3: Rating of a hypoid gear set according to Method B1
and Method B2 125

Annex D (informative) Sample 4: Rating of a hypoid gear set according to Method B1

and Method B2 185
Annex E (informative) Graphical representation of the calculation results for
Sample 1 to Sample 4 243
Bibliography 246
© ISO 2017 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/TR 10300-30:2017(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national

standards bodies (ISO member bodies). The work of preparing International Standards is

normally carried out through ISO technical committees. Each member body interested in a subject

for which a technical committee has been established has the right to be represented on that

committee. International organizations, governmental and non‐governmental, in liaison with ISO,

also take part in the work. ISO collaborates closely with the International Electrotechnical

Commission (IEC) on all matters of electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance

are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria

needed for the different types of ISO documents should be noted. This document was drafted in

accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the

subject of patent rights. ISO shall not be held responsible for identifying any or all such patent

rights. Details of any patent rights identified during the development of the document will be in

the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does

not constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to

the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see the

following URL: www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 60, Gears, Subcommittee SC 2, Gear

capacity calculation.
A list of all parts in the ISO 10300 series can be found on the ISO website.
iv © ISO 2017– All rights reserved
---------------------- Page: 4 ----------------------
ISO/TR 10300-30:2017(E)
Introduction

The ISO 10300 series consists of International Standards, Technical Specifications (TS) and

Technical Reports (TR) under the general title Calculation of load capacity of bevel gears

(see Table 1).

— International Standards contain calculation methods that are based on widely accepted

practices and have been validated.
— TS contain calculation methods that are still subject to further development.
— TR contain data that is informative, such as example calculations.

The procedures specified in ISO 10300‐1 to ISO 10300‐19 cover fatigue analyses for gear rating.

The procedures described in ISO 10300‐20 to ISO 10300‐29 are predominantly related to the

tribological behaviour of the lubricated flank surface contact. ISO 10300‐30 to ISO 10300‐39

include example calculations. The ISO 10300 series allows the addition of new parts under

appropriate numbers to reflect knowledge gained in the future.

Requesting standardized calculations according to ISO 10300 without referring to specific parts

requires the use of only those parts that are currently designated as International Standards (see

Table 1 for listing). When requesting further calculations, the relevant part or parts of ISO 10300

need to be specified. Use of a Technical Specification as acceptance criteria for a specific design

need to be agreed in advance between manufacturer and purchaser.
Table 1 — Overview of ISO 10300
International Technical Technical
Calculation of load capacity of bevel gears
Standard Specification Report
Part 1: Introduction and general influence factors X
Part 2: Calculation of surface durability (pitting) X
Part 3: Calculation of tooth root strength X
Part 4 to 19: to be assigned
Part 20: to be assigned for scuffing of bevel and hypoid
gears
Part 21 to 29: to be assigned
Part 30: ISO rating system for bevel and hypoid gears
— Sample calculations

At the time of publication of this document, some of the parts listed here were under development. Consult the ISO

website.

This document was prepared with sample calculations for different bevel gear designs. They are

intended for users of the ISO 10300 series to follow a whole calculation procedure formula by

formula. Practical experience has shown that this way, to get into a complex subject, is very

helpful.

On the other hand, this document is not intended for use by the average engineer. Rather, it is

aimed at the well‐versed engineer capable of selecting reasonable values for the parameters and

factors in these formulae based on knowledge of similar designs and on awareness of the effects

behind these formulae.
© ISO 2017 – All rights reserved v
---------------------- Page: 5 ----------------------
ISO/TR 10300-30:2017(E)
vi © ISO 2017– All rights reserved
---------------------- Page: 6 ----------------------
TECHNICAL REPORT ISO/TR 10300-30:2017(E)
Calculation of load capacity of bevel gears —
Part 30: ISO rating system for bevel and hypoid
gears — Sample calculations
1 Scope

This document provides sample calculations for different bevel gear designs, how the load

capacity is numerically determined according to the methods and formulae of the

ISO 10300 series. The initial geometric gear data necessary for these calculations in accordance

with ISO 23509.

The term “bevel gear” is used to mean straight, helical (skew), spiral bevel, zerol and hypoid gear

designs. Where this document pertains to one or more, but not all, the specific forms are

identified.

The manufacturing process of forming the desired tooth form is not intended to imply any

specific process, but rather to be general in nature and applicable to all calculation methods of the

ISO 10300 series. The fact that there are bevel gear designs with tapered teeth and others where

the tooth depth remains constant along the face width (uniform depth) does not demand to apply

Method B2 for the first and Method B1 for the second tooth configuration.

The rating system of the ISO 10300 series is based on virtual cylindrical gears and restricted to

bevel gears whose virtual cylindrical gears have transverse contact ratios of ε < 2. Additionally,

the given relations are valid for bevel gears of which the sum of profile shift coefficients of pinion

and wheel is zero (see ISO 23509).

WARNING: The user is cautioned that when the formulae are used for large average mean spiral

angles, (β + β )/2 > 45°, for effective pressure angles, α > 30° and/or for large face widths,

m1 m2 e

b > 13 m , the calculated results of the ISO 10300 series should be confirmed by experience.

2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies.

For undated references, the latest edition of the referenced document (including any

amendments) applies.

ISO 10300‐1:2014, Calculation of load capacity of bevel gears — Part 1: Introduction and general

influence factors

ISO 10300‐2:2014, Calculation of load capacity of bevel gears — Part 2: Calculation of surface

durability (pitting)

ISO 10300‐3:2014, Calculation of load capacity of bevel gears — Part 3: Calculation of tooth root

strength
© ISO 2017 – All rights reserved 1
---------------------- Page: 7 ----------------------
ISO/TR 10300-30:2017(E)
3 Terms and definitions

For the purposes of this document, the terms and definitions given in ISO 10300‐1 and

ISO 10300‐2 apply.

ISO and IEC maintain terminological databases for use in standardization at the following

addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
4 Symbols and abbreviated terms

For the purposes of this document, the symbols and units given in ISO 10300‐1:2014, Table 1 and

Table 2, as well as the abbreviated terms given in ISO 10300‐2:2014, Table 1, apply.

Table 2 — Symbols and units used in ISO 10300 (all parts)
Symbol Description or term Unit
a hypoid offset mm
a relative hypoid offset —
rel
a centre distance of virtual cylindrical gear pair mm
a centre distance of virtual cylindrical gear pair in normal section mm
b face width mm
b related base face width —
b calculated effective face width mm
b effective face width (e.g. measured length of contact pattern) mm
eff
b face width of virtual cylindrical gears mm
b effective face width of virtual cylindrical gears mm
v eff
c mean addendum factor of wheel —
ham
c empirical parameter to determine the dynamic factor —
c mean value of mesh stiffness per unit face width N/(mm · µm)
c mesh stiffness for average conditions N/(mm · µm)
c’ single stiffness N/(mm · µm)
c single stiffness for average conditions N/(mm · µm)
d outer pitch diameter mm
d mean pitch diameter mm
d tolerance diameter according to ISO 17485 mm
d reference diameter of virtual cylindrical gear mm
d tip diameter of virtual cylindrical gear mm
d tip diameter of virtual cylindrical gear in normal section mm
van
d base diameter of virtual cylindrical gear mm
2 © ISO 2017 – All rights reserved
---------------------- Page: 8 ----------------------
ISO/TR 10300-30:2017(E)
Symbol Description or term Unit
d base diameter of virtual cylindrical gear in normal section mm
vbn
d root diameter of virtual cylindrical gear mm
d reference diameter of virtual cylindrical gear in normal section mm
e exponent for the distribution of the load peaks along the —
lines of contact
f distance from the centre of the zone of action to a contact line mm
f maximum distance to middle contact line mm
max
f maximum distance to middle contact line at right side of mm
maxB
the contact pattern
f maximum distance to middle contact line at left side of mm
max0
the contact pattern
f single pitch deviation µm
f effective pitch deviation µm
p eff
f Influence factor of limit pressure angle
αlim
g length of contact line (Method B2) mm
g length of path of contact of virtual cylindrical gear in transverse mm
section
g related length of action in normal section —
vαn
g length of action from mean point to point of load application mm
(Method B2)
g relative length of action within the contact ellipse mm
h mean addendum mm
h tool addendum mm
h mean dedendum mm
h dedendum of the basic rack profile mm
h mean whole depth used for bevel spiral angle factor mm
h relative mean virtual dedendum —
vfm
h bending moment arm for tooth root stress (load application mm
at tooth tip)
h load height from critical section (Method B2) mm
j outer normal backlash mm
′ —
contact shift factor
k clearance factor —
k depth factor —
k basic crown gear addendum factor (related to m ) —
hap mn
k basic crown gear dedendum factor (related to m ) —
hfp mn
k circular thickness factor —
l length of contact line (Method B1) mm
© ISO 2017 – All rights reserved 3
---------------------- Page: 9 ----------------------
ISO/TR 10300-30:2017(E)
Symbol Description or term Unit
l theoretical length of contact line mm
l theoretical length of middle contact line mm
m outer transverse module mm
m mean normal module mm
m mean transverse module mm
m mass per unit face width reduced to the line of action of kg/mm
red
dynamically equivalent cylindrical gears
m* related individual gear mass per unit face width referred to kg/mm
the line of action
n rotational speed min
n resonance speed of pinion min
p peak load N/mm
p transverse base pitch (Method B2) mm
p maximum peak load N/mm
max
p* related peak load for calculating the load sharing factor (Method B1) —
p relative mean normal pitch —
p relative mean normal base pitch —
p transverse base pitch of virtual cylindrical gear (Method B1) mm
vet
q exponent in the formula for lengthwise curvature factor —
q notch parameter —
r cutter radius mm
r tooth fillet radius at the root in mean section mm
r mean pitch radius mm
mpt
r mean transverse radius to point of load application (Method B2) mm
my 0
r relative mean virtual tip radius —
r relative mean virtual pitch radius —
s mean normal circular thickness mm
s amount of protuberance at the tool mm
s tooth root chord in calculation section mm
s one‐half tooth thickness at critical section (Method B2) mm
u gear ratio of bevel gear —
u gear ratio of virtual cylindrical gear —
v tangential speed at outer end (heel) of the reference cone m/s
v maximum pitch line velocity at operating pitch diameter m/s
et max
v sliding velocity in the mean point P m/s
v sliding velocity parallel to the contact line m/s
g par
v sliding velocity vertical to the contact line m/s
g vert
4 © ISO 2017 – All rights reserved
---------------------- Page: 10 ----------------------
ISO/TR 10300-30:2017(E)
Symbol Description or term Unit
v tangential speed at mid face width of the reference cone m/s
v sum of velocities in the mean point P m/s
v sum of velocities in profile direction m/s
v sum of velocities in lengthwise direction m/s
v sum of velocities vertical to the contact line m/s
Σ vert
w angle of contact line relative to the root cone °
x profile shift coefficient —
x thickness modification coefficient (backlash included) —
x thickness modification coefficient (theoretical) —
smn
x tooth strength factor (Method B2) mm
x distance from mean section to point of load application mm
y running‐in allowance for pitch deviation related to the polished µm
test piece
y location of point of load application for maximum bending stress mm
on path of action (Method B2)
y location of point of load application on path of action for mm
maximum root stress
y running‐in allowance for pitch error µm
z number of teeth —
z number of teeth of virtual cylindrical gear —
z number of teeth of virtual cylindrical gear in normal section —
z number of blade groups of the cutter —
A auxiliary factor for calculating the dynamic factor K − —
v C
A* related area for calculating the load sharing factor Z mm
A outer tooth thickness allowance mm
sne
B accuracy grade according to ISO 17485 —
C correction factor of tooth stiffness for non‐average conditions —
C correction factor for the length of contact lines —
C , C , C constants for determining lubricant film factors —
ZL ZR ZV
E modulus of elasticity, Young’s modulus N/mm
E, G, H auxiliary variables for tooth form factor (Method B1) —
F auxiliary variable for mid‐zone factor —
F nominal tangential force at mid face width of the reference cone N
F determinant tangential force at mid face width of the reference cone N
mtH
F nominal normal force N
F nominal tangential force of virtual cylindrical gears N
vmt
HB Brinell hardness —
© ISO 2017 – All rights reserved 5
---------------------- Page: 11 ----------------------
ISO/TR 10300-30:2017(E)
Symbol Description or term Unit
K constant; factor for calculating the dynamic factor K —
v−B
K dynamic factor —
K* preliminary dynamic factor for non‐hypoid gears —
K application factor —
K lengthwise curvature factor for bending stress —
K transverse load factor for bending stress —
K face load factor for bending stress —
K transverse load factor for contact stress —
K * preliminary transverse load factor for contact stress for —
non‐hypoid gears
K face load factor for contact stress —
K mounting factor —
Hβ−be
N reference speed related to resonance speed n —
N number of load cycles —
P nominal power kW
Ra = CLA = AA arithmetic average roughness µm
R outer cone distance mm
R mean cone distance mm
R relative mean back cone distance —
mpt
Rz mean roughness µm
Rz mean roughness for gear pairs with relative curvature radius µm
ρ = 10 mm
rel
S safety factor for bending stress (against breakage) —
S minimum safety factor for bending stress —
F min
S safety factor for contact stress (against pitting) —
S minimum safety factor for contact stress —
H min
T nominal torque of pinion and wheel Nm
1,2
W wheel mean slot width mm
Y tooth form factor of pinion and wheel (Method B2) —
1,2
Y stress concentration and stress correction factor (Method B2) —
Y inertia factor (bending) —
Y root stress adjustment factor (Method B2) —
Y bevel spiral angle factor —
Y tooth form factor for load application at the tooth tip (Method B1) —
Y combined tooth form factor for generated gears —
Y bending strength geometry factor (Method B2) —
Y load sharing factor (bending) —
6 © ISO 2017 – All rights reserved
---------------------- Page: 12 ----------------------
ISO/TR 10300-30:2017(E)
Symbol Description or term Unit
Y life factor (bending) —
Y relative surface condition factor —
R rel T
Y stress correction factor for load application at the tooth tip —
Y stress correction factor for dimensions of the standard test gear —
Y size factor for tooth root stress —
Y relative notch sensitivity factor —
δ rel T
Y contact ratio factor for bending (Method B1) —
Z inertia factor (pitting) —
Z speed factor —
Z contact stress adjustment factor (Method B2) —
Z elasticity factor —
Z face width factor —
Z hypoid factor —
Hyp
Z pitting resistance geometry factor (Method B2) —
Z bevel gear factor (Method B1) —
Z lubricant factor —
Z load sharing factor (Method B1) —
Z mid zone factor —
M‐B
Z life factor (pitting) —
Z roughness factor for contact stress —
Z bevel slip factor —
Z work hardening factor —
Z size factor —
α adjusted pressure angle (Method B2) °
α normal pressure angle at tooth tip °
α  nominal design pressure angle for drive side/coast side °
dD,C
α effective pressure angle in transverse section °
α effective pressure angle for drive side/coast side °
eD,C
α limit pressure angle in wheel root coordinates (Method B2) °
α limit pressure angle °
lim
α generated pressure angle for drive side/coast side °
nD,C
α transverse pressure angle of virtual cylindrical gears °
vet
α load application angle at tooth tip of virtual cylindrical gear °
Fan
(Method B1)
α normal pressure angle at point of load application (Method B2) °
β mean base spiral angle °
β mean spiral angle °
© ISO 2017 – All rights reserved 7
---------------------- Page: 13 ----------------------
ISO/TR 10300-30:2017(E)
Symbol Description or term Unit
β helix angle of virtual gear (Method B1), °
virtual spiral angle (Method B2)
β helix angle at base circle of virtual cylindrical gear °
β inclination angle of contact line °
γ auxiliary angle for length of contact line calculation (Method B1) °
γ ′ projected auxiliary angle for length of contact line °
γ auxiliary angle for tooth form and tooth correction factor °
δ pitch angle of bevel gear °
δ face angle °
δ root angle °
ε transverse contact ratio of virtual cylindrical gears —
ε transverse contact ratio of virtual cylindrical gears in normal section —
vαn
ε face contact ratio of virtual cylindrical gears —
ε virtual contact ratio (Method B1), modified contact ratio (Method B2) —
ε load sharing ratio for bending (Method B2) —
ε load sharing ratio for pitting (Method B2) —
ζ pinion offset angle in axial plane °
ζ pinion offset angle in pitch plane °
ζ pinion offset angle in root plane °
θ auxiliary quantity for tooth form and tooth correction factors —
θ auxiliary angle for virtual face width (Method B1) °
θ  addendum angle of wheel °
θ  dedendum angle of wheel °
θ  angular pitch of virtual cylindrical wheel radiant
ξ assumed angle in locating weakest section °
ξ one half of angle subtended by normal circular tooth thickness °
at point of load application
ρ density of gear material kg/mm
ρ cutter edge radius mm
ρ fillet radius at point of contact of 30° tangent mm
ρ fillet radius at point of contact of 30° tangent in normal section mm
ρ root fillet radius of basic rack for cylindrical gears mm
ρ radius of relative curvature vertical to contact line at mm
rel
virtual cylindrical gears
ρ radius of relative profile curvature (Method B2) mm
ρ  relative edge radius of tool —
va0
ρ′ slip layer thickness mm
8 © ISO 2017 – All rights reserved
---------------------- Page: 14 ----------------------
ISO/TR 10300-30:2017(E)
Symbol Description or term Unit
σ tooth root stress N/mm
σ  nominal tooth root stress N/mm
σ nominal stress number (bending) N/mm
F lim
σ allowable stress number (bending) N/mm
σ permissible tooth root stress N/mm
σ contact stress N/mm
σ allowable stress number for contact stress N/mm
H lim
σ permissible contact stress N/mm
τ angle between tangent of root fillet at weakest point and °
centreline of tooth
ν Poisson’s ratio —
ν lead angle of face hobbing cutter °

ν , ν nominal kinematic viscosity of the oil at 40 °C and 50 °C, respectively mm/s

40 50
ϕ auxiliary angle to determine the position of the pitch point °
ω angular velocity rad/s
ω angle between the sum of velocities vector and the trace of pitch cone °
X −1
χ relative stress drop in notch root mm
X −1
χ mm
relative stress drop in notch root of standardized test gear
Σ shaft angle °
Table 3 — Generally used subscripts in ISO 10300 (all parts)
Subscripts Description
0 tool
1 pinion
2 wheel
A, B, B1, B2, C value according to Method A, B, B1, B2 or C
D drive flank
C coast flank
T relative to standardized test gear dimensions
(1), (2) trials of interpolation
© ISO 2017 – All rights reserved 9
---------------------- Page: 15 ----------------------
ISO/TR 10300-30:2017(E)
5 Application
5.1 General
This document provides four sample calculations:

— Sample 1 is a rating of a spiral bevel gear pair without hypoid offset according to Method B1

and Method B2 (see Annex A);

— Sample 2 is a rating of a hypoid gear set according to Method B1 and Method B2 (see

Annex B);

— Sample 3 is a rating of a hypoid gear set according to Method B1 and Method B2 (see

Annex C);

— Sample 4 is a rating of a hypoid gear set according to Method B1 and Method B2 (see

Annex D).
5.2 Structure of calculation methods

Figure 1 shows three boxes that represent the individual three parts of ISO 10300. However,

these boxes are subdivided into a left side where influence factors are determined on the basis of

mainly operational data according to Methods A, B or C (see ISO 10300‐1:2014, 5.1) and a right

side where separate calculation procedures are provided according to Method B1 and Method B2

which are assumed to have the same level B but different approaches. These two methods refer to

the determination of virtual cylindrical gears in ISO 10300‐1, the gear flank rating formulae in

ISO 10300‐2 and the gear tooth rating formulae in ISO 10300‐3.
10 © ISO 2017 – All rights reserved
---------------------- Page: 16 ----------------------
ISO/TR 10300-30:2017(E)
One set of formulae for both, bevel and hypoid gears.
Separate sets of formulae for bevel and for hypoid gears.
Figure 1 — Structure of calculation methods in ISO 10300 (all parts)
© ISO 2017 – All rights reserved 11
---------------------- Page: 17 ----------------------
ISO/TR 10300-30:2017(E)
Annex A
(informative)
Sample 1: Rating of a spiral bevel gear pair without hypoid offset
according to Method B1 and Method B2
A.1 Initial data

Sample 1 is for a spiral bevel gear pair without hypoid offset which uses Method 0 according to

ISO 23509.
Table A.1 — Initial data for pitch cone parameters
Symbol Description Method 0 Method 1 Method 2 Method 3
Σ  shaft angle 90° X X X
a  hypoid offset 0 mm X X X
z number of teeth 14/39 X X X
1,2
d mean pitch diameter of wheel — — X —
d outer pitch diameter of wheel 176,893 mm X — X
b wheel face width 25,4 mm X X X
β mean spiral angle of pinion 35° X — —
β mean spiral angle of wheel 35° — X X
r cutter radius 114,3 mm X X X
number of blade groups
z — — X X
(only face hobbing)
12 © ISO 2017 – All rights reserved
---------------------- Page: 18 ----------------------
ISO/TR 10300-30:2017(E)
Table A.2 — Input data for tooth profile parameters
Data type I Data type II
Symbol Description Symbol Description
α 20°
α 20°
f 0
αlim
x — c 0,247 37
hm1 ham
k — k 2,000
hap d
k — k 0,125
hfp c
k 0,091 5
x —
smn
W —
j 0,127 mm
θ 2,134 2°
θ 6,493 4°
ρ  0,8 mm/0,8 mm
a01D,C
ρ  1,2 mm/1,2 mm
a02D,C
s 0 mm/0 mm
pr1D,C
s 0 mm/0 mm
pr2D,C
© ISO 2017 – All rights reserved 13
---------------------- Page: 19 ----------------------
ISO/TR 10300-30:2017(E)

Table A.3 and Table A.4 show geometric and operational data and text for explanation.

Table A.3 — Geometric data from calculation according to ISO 23509
Symbol Description Values Symbol Description Value
mean pitch diameter 54,918 mm/ offset angle
d ζ 0°
m1,2 mp
of pinion/wheel 152,987 mm on pitch plane
mean addendum 4,836 mm/ pinion offset angle
h ζ 0°
am1,2 R
of pinion/wheel 1,591 mm on root plane
mean dedendum 2,394 mm/ outer cone distance
h R 93,973 mm
fm1,2 e1,2
of pinion/wheel 5,639 mm on pinion and wheel
effective pressure angle mean cone distance
α 20°/20° R 81,273 mm
eD,C m1,2
for drive side/coast side on pinion and wheel
generated pressure angle pitch angle 19,747°/
α 20°/20° δ
nD,C 1,2
for drive side/coast side on pinion/wheel 70,253°
face angle 26,240°/
α limit pressure angle 0° δ
lim a1,2
on pinion/wheel 72,387°
root angle 17,613°/
m mean normal module 3,213 mm δ
mn f1,2
on pinion/wheel 63,760°
thickness modification
basic crown gear 0,037/
k 1,25 x coefficient on
hfp sm1,2
dedendum factor −0,055
pinion/wheel
pinion offset angle
ζ 0,000° m outer transverse module 4,536 mm
m et2
on axial plane
mean normal circular
6,465 mm/
s  tooth thickness
mn1,2
3,511 mm
of pinion/wheel
14 © ISO 2017 – All rights reserved
---------------------- Page: 20 ----------------------
ISO/TR 10300-30:2017(E)
Table A.4 — Operation parameters and additional considerations
Symbol Description Value
Additional data
wheel profile generated
roughing/finishing method face milling
b effective face width on wheel 0,85 · b
2eff 2
profile crowning low
verification of contact pattern checked under light test load for each gear
mounting conditions of pinion and wheel one member cantilever‐mounted
Operation parameters
T pinion torque 300 Nm
n pinion rotational speed 1 200 min
K application factor 1,1
active flank drive
Material data for pinion and wheel (case hardened steel)
σ allowable stress number (contact) 1 500 N/mm
H lim
σ nominal stress number (bending) 480 N/mm
F lim
surface hardness same for pinion and wheel
Quality par
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.